Need to find computer name from MAC address


Recommended Posts

Ok so here at the company i work for we have determined that someone has been doing things they should not with the computers and all i had was an ip address and a MAC address and i have tried ARP and NBTSTAT and i am unable to get the computer name from either of the numbers is there another way that i can find the computer name from either the IP address or MAC address.

Depending on your network setup you could also Browse the computer using a domain admin account etc.

Just go to any computer and type \\ipadd\c$ in the address bar of explorer.

This should let you browse the mydocuments folder which should give you enough information to figure out where they are.

http://www.coffer.com/mac_find/ may help you at least determine what kind of device it is.

You really have no WINS, DNS, or DHCP servers? most logs here are small and will often tell hostname requesting the info.

Do you have managed switches to set up port mirroring or if connected to a hub or at least if managed. Disconnect them or thier lan segment as last resort.

You can sniff the traffic.

If you can't get the Hostname using a NBTSTAT -a xxx.xxx.xxx.xxx (replaces x with ip) then the box is either firewalled. Does not respond to because it isnt a PC might be like a router, switch , printer etc.

try http or https to the hosts IP

attempt to telnet to it

try SSH to it.

lastly GO look for strange devices or PC

is your dhcp server a box (computer, windows, linux) or a router (cisco, netgear, etc.)?

If its a windows or linux box, you can look up the host name in the dhcp scope. If you have absolutely no idea what the box is, or who it is, then run nmap on it to see what ports the machine has open and what the make of the network card is. usually that might point you in the right direction.

if all else fails, kick them from the network or quarantine them, and first person who comes and bitches about it, is the culprit.

We know that it is a Dell computer, We know that it has to be wired in (our wireless network has a different IP set) and we know what the MAC address is. Also we know there is no current computer on the network that has the ip address that it had when it was causing problems. I think i might just have to go from computer to computer and check their mac addresses.

  littleneutrino said:
We know that it is a Dell computer, We know that it has to be wired in (our wireless network has a different IP set) and we know what the MAC address is. Also we know there is no current computer on the network that has the ip address that it had when it was causing problems. I think i might just have to go from computer to computer and check their mac addresses.

Block the MAC and see who complains they can't access the network.

"to go from computer to computer and check their mac addresses. "

Why is that? And why do you need the name? Are you switches not managed? On a managed switch you can always track down what port a mac address is connected too.. Even if the cheapest smart switches support this.

For example from $80 my home gig switch!

post-14624-1247153123_thumb.jpg

Ports with more than one mac address on them have downstream switches connected, etc.

finding what port a mac is connect to on cisco swith is as easy as

show mac-address-table | inc partofmacaddress

Once you no the port -- go to that port and follow the wire and you have your computer ;)

  fAlCoNNiAn said:
...

if all else fails, kick them from the network or quarantine them, and first person who comes and bitches about it, is the culprit.

  GreyWolfSC said:
Block the MAC and see who complains they can't access the network.

Great minds think alike.

This topic is now closed to further replies.
  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Posts

    • Hmm, I'll give it a go
    • Is Samsung teasing a Galaxy Z Fold7 Ultra? An official press release suggests so by Sagar Naresh Bhavsar We are inching closer to the launch of this year's premium foldables from Samsung: the Galaxy Z Fold7 and the Galaxy Z Flip7. Recently, a certification revealed that the affordable Galaxy Z Flip7 FE, could also debut alongside the other two foldables. The device is expected to take on the standard Moto Razr 2025. While we were getting excited about the trio, Samsung has put out a press release to create some hype around the upcoming foldables. Interestingly, the company has put great emphasis on the "Ultra" branding, which it usually uses for its Galaxy S-series phone and previously for Note-series phones. So, does this mean, we are getting a Galaxy Z Fold7 Ultra? Time will only tell. As for the press release, it is titled "Meet the Next Chapter of Ultra" and the first line highlights how Samsung has been listening to fans that have demanded "bigger screens, better cameras and new ways to connect and create." To churn up up the hype, Samsung added, "That’s why Galaxy’s next chapter is to provide an experience that seamlessly blends artistry and engineering to elevate everyday interactions." The GIF inside the press-release reveals what looks like the Galaxy Z Fold7 (or the Galaxy Z Fold7 Ultra, if that exists). Rumors have indicated that this year's Galaxy Z Fold7 is getting taller and wider than last year's model, thanks to a bigger display. The Z Fold7 could also feature a titanium backplate to not only reduce its thickness and make it stronger but to shed some weight as well. The company then directs the attention to its AI features such as voice controls for finding the perfect eatery or shopping place, using powerful AI-powered camera features, and so on. We will get to know more about the devices in the coming weeks. By that time, let us know your thoughts, on whether you would like an Ultra foldable or want Samsung to tweak the existing model and keep the space less-crowded.
    • A couple of friends of mine have been building Gunpla for years and got me interested, so I asked and they recommended this as a fairly good quality, very affordable, starting point. https://www.amazon.co.uk/dp/B0BGN9K1MV It was fun to build, didn't take too long, and helped me decide if I wanted to go further with the hobby, which I did.  Still only got this one built, but that's only due to time availability!
    • I've had an original, a Lite, and an OLED and I have just one question for you.  How big are your hands? I got rid of all three because, simply put, they're sized for kids hands more than anything, especially the Lite.  The Switch 2 is a fair bit larger but I'm not agreeing to Ninty's new EULA for the thing.
    • Where does he say that he'll give 99% to Africa? I agree that he said that he'll give 99% of his wealth, and you quote him saying that the majority will go to Africa. The majority of 99% does not mean all of the 99%. It could mean that he'll give just above half of that.
  • Recent Achievements

    • Week One Done
      Leonard grant earned a badge
      Week One Done
    • One Month Later
      portacnb1 earned a badge
      One Month Later
    • Week One Done
      portacnb1 earned a badge
      Week One Done
    • First Post
      m10d earned a badge
      First Post
    • Conversation Starter
      DarkShrunken earned a badge
      Conversation Starter
  • Popular Contributors

    1. 1
      +primortal
      260
    2. 2
      snowy owl
      158
    3. 3
      +FloatingFatMan
      145
    4. 4
      ATLien_0
      140
    5. 5
      Xenon
      131
  • Tell a friend

    Love Neowin? Tell a friend!