Need some help setting my access point to repeater mode


Recommended Posts

OK i've been searching around the net for some time now and this site pops up in many of my search terms so i thought i'd try asking here

I have a Linksys WAG300N router connected to my pc via ethernet. I have set it to broadcast wirelessly and everything is working fine but the thing is that the signal reception is bad in the living room resulting in unstable connection when i try to use my laptop in the living room. I think the main reason for that is that between my room and the living room interfere a lot of walls (two of which are outer walls so they are thicker). I bought a netgear wireless-N access point the model is WN802T v2. In its setup there is a wireless bridge option with two submenus. One is "wireless point to multipoint bridge" while the other is "repeater without wireless client association". However i can't seem to find a way to make it work. Both the router and the access point have their default firmwares installed i haven't messed with anything there.

Thanks in advance for your time any help will be apreciated ^^

Well for starters I would surely update the firmware to the latest, I show 3.11 out for that access point and Ver.1.01.07 for the router -- are you running these latest firmwares?

For wireless repeating to work you will have to make setting on both your router and your accesspoint. SSID will match, security settings will match, etc..

On your router under WDS you would setup repeating with client access, and you would put in the mac address of your accesspoint.

On your repeater/accesspoint you would put in point to point bridge and also enable client associations.

I would highly suggest you go over this guide from netgear and repeating with your accesspoint.

http://kb.netgear.com/app/answers/detail/a_id/12848

Now its using a different router (netgear one) But the details of what you have to do will be the same, just on your router the setting might called something slightly different or in a different section of the UI, etc.

OK i have two questions about that. First of all i don't know if my linksys router supports WDS and i can't seem to find something about that in the net.

Secondly i can't seem to find where i can download the latest firmware and i think the 07 version is still in beta.

Well for your linksys the firmware is here.

http://www.linksysbycisco.com/UK/en/support/WAG300N/download

firmware

* Ver.1.01.07 (ETSI) Annex A

Download 7.46 MB

(Firmware)

Release Notes

Firmware

* Ver.1.01.05

Download 4.66 MB

(Firmware)

Not sure if the 1.01.07 is your model? Not sure what (ETSI) Annex A means exactly.. But they newer than initial firmware from the release notes, and do have bug fixes. As to WDS support, yeah just looked at the manual -- and did not see any mention of it either.. If your wireless router does not support this mode - it might not be possible to use your accesspoint as a repeater? Which is why is always a good idea to use same manufacturer when wanting to do stuff like this.. And from my personal experience the Gateway models seem to be more limited in features than the stand alone routers. And they really limit your ability to run 3rd party firmware that will add features, like WDS for example.

If your router does not support WDS mode - then you would need to use your accespoint as jut a wireless client in bridge mode.. Sometimes you can only use wired clients this way.. Depends on the firmware feature set.. I just looked and does not look like dd-wrt is supported on either of these devices.. Too bad since it does support WDS for starters and does have a wireless bridge with wireless client support.

http://www.dd-wrt.com/wiki/index.php/Repeater_Bridge

The limitation with standard bridging is that it only allows wired clients to connect to your secondary router. Wireless clients cannot connect to your secondary router configured as a standard bridge.

New in DD-WRT v24 is Repeater Bridge mode. This extends your primary LAN via secondary router (bridge router) and also allows wireless clients to connect to your secondary router. This extends the range of your wireless network while simultaneously allowing wired clients to connect to your secondary router.

From the quick look I did at your accesspoint this feature did not jump out at me - maybe it supports it, maybe it doesnt. According to the doc I linked to seems to show only WDS mode to allow you use wireless clients with the accesspoint and also maintain a wireless connection to the main router.

You might want to look into getting the netgear gateway (modem/router) listed in the doc I listed - as this clearly supports the mode your after. Your other option would be to run a wire to the accesspoint and use it as a normal accesspoint.

Good Luck!

This topic is now closed to further replies.
  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Posts

    • Was sort of sceptical about the unload page feature , just tried it and it does actually drop memory usage. 22 tabs open(1.65gb Ram) and after unloading Facebook as a test it dropped to 1.2gb
    • Elon Musk doesn't want you to know Tesla's response to the NHTSA's Robotaxi questions by David Uzondu Recently, Tesla's Robotaxi service began operating in Austin, and almost immediately, the company decided it would prefer you didn't see its homework. Before the launch, the National Highway Traffic Safety Administration (NHTSA) sent Tesla a letter with a deadline of June 19th to answer some questions. Now that Tesla has replied, it has requested that the NHTSA withhold the entire response from the public, classifying it as confidential business information. This isn't too surprising, as the company is notoriously secretive about its performance data, especially in areas like Autopilot and Full Self-Driving. Here are a few paraphrased versions of the questions Tesla faced: How will the system handle bad weather or poor visibility? What happens if the system detects that it cannot drive safely? Does it pull over? Will a human be monitoring the cars remotely or in person? Does the system follow any existing industry standards for autonomous driving? When does Tesla plan to let other people operate their own cars as robotaxis? The feds have good reason to ask. On its first day, Tesla's Robotaxi service was caught on video making some questionable moves, including driving in the wrong lane against traffic, as seen below (full video here). The clip was also shared in our community forums, though you'll need a free membership to access the off-topic section. Here's another showing a Robotaxi dropping passengers in the middle of an intersection. For now, the service runs with a human safety driver (likely a Tesla employee) in the passenger seat. Billionaire Dan O'Dowd, a persistent critic of Tesla's software, felt the company's launch was lackluster, and the videos circulating online demonstrate that the technology is years behind competitors like Waymo, which has operated without in-car supervisors since 2019. For its part, NHTSA acknowledged being aware of the widely reported incidents and is in contact with Tesla to get more information. The agency's statement reminded the public that manufacturers self-certify their vehicles' safety, and NHTSA's role is to investigate and act on safety problems after they are on the road: This situation gets even more interesting when you look at the bigger picture. Musk has already been criticized for his role in the Department of Government Efficiency (DOGE), which has led to job cuts at agencies that oversee his companies, including the Federal Aviation Administration (FAA) for SpaceX, the Food and Drug Administration (FDA) for Neuralink, and, of course, NHTSA. This has led some to worry about regulatory capture. As one cynical comment on Electrek's article notes, the official who signed the letter to Tesla, Tanya Topka, Director of NHTSA's Office of Defects Investigation, may have put a target on her back just for trying to hold the company accountable.
    • Have you ever developed a game for Xbox and Windows at the same time? To say that they are not the same operating system and the same DirecTx by chance?? It's obvious that it isn't, right? So what if Xbox uses HyperV? What difference does that make to a game developer? The PS4 is more different than the PS5, different operating systems and different APIs. The games are not backwards compatible However, a game made in Windows can be transferred to Xbox SX in a few weeks with little programming costs because they are the same API and the same Windows
    • Idiot, FH5 sold more on Xbox and Windows than on PS5. You tell lies like that and think no one will check, right? There are a lot of FIFA and CoD hacks on PS4 and PS5 being used every day and Sony doesn't do anything. You can also buy a game's Platinum achievement without having bought the game and Sony doesn't do anything.
  • Recent Achievements

    • First Post
      956400 earned a badge
      First Post
    • Week One Done
      davidfegan earned a badge
      Week One Done
    • First Post
      Ainajohn earned a badge
      First Post
    • Conversation Starter
      sophiaisabella32 earned a badge
      Conversation Starter
    • First Post
      Brett76 earned a badge
      First Post
  • Popular Contributors

    1. 1
      +primortal
      590
    2. 2
      ATLien_0
      225
    3. 3
      Michael Scrip
      172
    4. 4
      +FloatingFatMan
      148
    5. 5
      Xenon
      133
  • Tell a friend

    Love Neowin? Tell a friend!