running a generator non stop - will it hurt anything?


Recommended Posts

been living on a 6.5kW generator for the last three days now up here in middle New York

the generator - a Yamaha gasoline engine on a Homelite portable wheeled chassis - has been running almost nonstop for about 60 hours now, with only about 10 minutes of downtime this morning when it ran out of fuel. other than that we have been refueling it live. it was bought a year ago and prior to Tuesday it had maybe 12 hours on it since new. as far as we know, the load is well within the continuous output capacity of 6500 watts.

what i would like to know is, will it hurt or put excessive wear on anything to have this run for another 72 hours? 96 hours? should the machine be allowed an hour or few hour break? how often?

the electric utility company says its going to be at least a few days longer due to the weather getting worse as the week goes on.

When I was in the Army and we had to run off generators in the Field- It was customary for us to shut off power every 6 hours to check the oil and air filter as well as to fuel them up. (these were diesel though) ,

But you should probably read the manual... and occasionally shut it down to check the oil and air filter as well as to refuel. ( I would say every 4 - 6 hours to check the fluids then let it sit for at least 10 min ) not to mention if the belts are visible then check them. (some have chains and those you have to make sure are lubed) . Not to mention you should see if there are any lube points- though probably you are snowed in and don't have a grease gun.

If not then look online for a manual- usually they have a general maintenance section.

Also to note make sure that it is in a well ventilated area.

Though after this period of use you may want to consider getting the oil changed in the generator as soon as the weather clears.

is it a premium series or an inverter series of their generators? If your generator says it's 6500W then that is PEAK, NOT CONTINUOUS. Do not operate at a maximum power for more than 30 minutes. For continuous operations, do not exceed the rated power.

For example their E6600DE is 6600 watts peak, but 6000 continuous (which is still quite high because normally continuous is 50-60% of peak) with a running time of 7.4 hours at rated load.

Check out the current ones here: http://www.yamaha-motor.ca/products/index.php?group=G

i'm positive its 6500 continuous watts. no worries there, i know the difference between peak and continuous output. by the sound of the gen outside, we aren't even getting close to the continuous max for more than a little while at a time.

i am more worried about the engine really, but at least its cold, not hot, out there right now being the middle of winter so it won't overheat or anything. i will see about checking the oil tomorrow, something we forgot about really. as for shutting it down every few hours, its not going to happen with my family. dad dumps gas into it while its running as it is.

the manual is long hidden away and i'm not going outside to find out the model. it seems to be holding up well.

the power definitely isn't clean, the blower in the furnace is a tad quieter (and slower) and the incandescent lamp in our fridge has a noticeable flicker depending on the load. but it seems to be holding up well. it powers enough of this household to keep all 4 of us happy. energy efficient integrated florescent light bulbs (the 15w kind that screw in to replace regular 60w bulbs) are used in all other light sources and they operate just fine.

its connected to our mains box with a cable that provides two leg power (2x120 or 240 volts). we are careful as to what is running. so far its lighting, two small televisions, a 3 month old fridge, a trailer-sized oil burnig furnace from the 70s that is running about 60% of the time, cable modem and router, three laptops plugged in and powered on, a water pump hooked to an underground well, and for a short time this afternoon, my Oki LED page printer. if we kill the heat, the water heater can be run, usually for 30 minutes or so at a time we give it.same with the clothes dryer. no light dimming here, though i wish i had a P3 Kill-a-Watt handy

thanks for the replies, im going to sleep now :)

Do you really need power 24 hours a day?

Why not just run it for a few hours every once in a while to have the furnace run? I hope you don't have neighbors.. Power went out here a couple weeks ago at midnight and some ******* a door down fired up his generator at 1am and ran it all night. Needless to say that's the closest I've ever come to committing a crime (vandalization / sabotage of a generator).

Do you really need power 24 hours a day?

Why not just run it for a few hours every once in a while to have the furnace run? I hope you don't have neighbors.. Power went out here a couple weeks ago at midnight and some ******* a door down fired up his generator at 1am and ran it all night. Needless to say that's the closest I've ever come to committing a crime (vandalization / sabotage of a generator).

If you have a fridge/freezer... yes you do need power 24 hours a day.

If you have a fridge/freezer... yes you do need power 24 hours a day.

a Decent fridge and freezer should keep the cold for a considerable amount of time before they need power.

Freezers also last up to 3 days. fridges not so long but still depending on how often you open it it should last 12-24 hours.

Not sure what a gen like that can handle but whole home ones are great

http://www.amazon.com/Generac-5505-Air-Cooled-Automatic-Generator/dp/B001DZLKIW

connect right to your power and it auto switches on when the power goes out... nice to have them and they run off natural gas so no refilling

Not sure what a gen like that can handle but whole home ones are great

http://www.amazon.com/Generac-5505-Air-Cooled-Automatic-Generator/dp/B001DZLKIW

connect right to your power and it auto switches on when the power goes out... nice to have them and they run off natural gas so no refilling

dad is thinking of a 12000 watt diesel for a future upgrade, as it would be more than enough to power *everything* we normally use. natural gas would be nice, but i think he'd go for diesel because it could easily be hooked into our heating oil tank and would burn slightly cleaner for a cheaper price per gallon than standard road vehicle diesel fuel.

all else: turning off the heat for an hour makes the place pretty chilly, but the fridge temp creeps up to 50 degrees which isn't good for our food. tomorrow we plan for a two to three hour break.

and about the noise? there are at least 5 generators running on our road at any given moment, although i think we might be the only ones running one constant.

First off why do you need to run a freezer 24 hours per day? It is winter outside and you could put the stuff in a cooler and leave it outside unless of course the temperature is above freezing. Second of all that is why it is always good to have a wood burning stove in situations like that where power could be out for days. Luckily during the ice storm about 12 years ago it was only for a stretch of 8 hours that we were out but had constant loss of electricity.

Turning the heat off for an hour makes the place chilly? You probably have lousy insulation if that is the case and to save energy should put on more clothes. Sheesh talk about panzies.

When our power went out because of the wind storm in the Midwest, we ran our generator 12 at a time, and never had any issues except the noise. I used good quality fuel and Castrol oil, with some Jacobs added to the gas and oil. It worked great. We had 2 freezers, and a refrigerator, and they were fine with only 12 hours a day. The trick is to keep the freezers covered to keep the cold in. We had no power for 6 1/2 days.

We are planning to get a whole house generator, Costco has a 10k NG/PG unit (12k PG) that comes with auto 100 amp switch box (it will cover up to 150 if you upgrade), which is more then enough to power my house. It can handle most homes, and only cost $1997.99. It is a little larger then an air conditioner, but something that i plan to get, (the batteries for my UPS are getting to costly).

You don't need a fridge or freezer at a time like this, just pack your food in bins, and then bury the bins in the snow to keep it cold. I've worked with generators before, run it twelve hours on, then three hours down.

aren't your powerlines underground or something? I know a lot of snow has fallen, but really, a few days without power? There would be riots if something like that happened here, no one even has a generator over here :D

nah over here in America our power grid is old and unreliable. very newly built areas usually have utility lines underground and inner city areas of course have all wiring, fuel, and water lines buried

but not out in the woods where i live, here everything is suspended in open air on poles.

147000 customers in the dark is the power co's estimate as of last night

Not had a proper power failure here in years. When we do get a failure they last an hour or two at the most. I suppose we're lucky with underground utilities in much of the UK. I suppose it's worse out in the country with the traditional suspended lines.

I hope you get your power back soon.

This topic is now closed to further replies.
  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Posts

    • Now comes with a money back guarantee instead of a replacement! Hah
    • Rufus 4.15.2391 Beta by Razvan Serea Rufus is a small utility that helps format and create bootable USB flash drives, such as USB keys/pendrives, memory sticks, etc. Despite its small size, Rufus provides everything you need! Oh, and Rufus is fast. For instance it's about twice as fast as UNetbootin, Universal USB Installer or Windows 7 USB download tool, on the creation of a Windows 7 USB installation drive from an ISO (with honorable mention to WiNToBootic for managing to keep up). It is also marginally faster on the creation of Linux bootable USBs from ISOs. A non-exhaustive list of Rufus supported ISOs is available here. It can be especially useful for cases where: you need to create USB installation media from bootable ISOs (Windows, Linux, UEFI, etc.) you need to work on a system that doesn't have an OS installed you need to flash a BIOS or other firmware from DOS you want to run a low-level utility Rufus 4.15.2391 Beta changelog: Improve the guards for using the "silent" option Improve the ability to cancel during write retries Fix unrestricted XML entity expansion and integer overflow in ezxml parser (courtesy of @esadowski4) [GHSA-55r2-34wg-8mv9] Fix "silent" Windows installation failing at 75% in most cases [#2960] Fix a crash during boot when using UEFI:NTFS on Snapdragon X based ARM64 platforms [#2934] Fix the first WUE option always being checked by default [#2965] Fix an infinite loop when using Windows ISOs that contain multiple WIMs Fix "Enable runtime UEFI media validation" checkbox not always being properly enabled Other WUE improvements/fixes for OneDrive removal and username validation (with thanks to @christian8641) [#2984, #2991] Download: Rufus 4.15 Beta | 1.9 MB (Open Source) Links: Rufus Home Page | Project Page @GitHub | Screenshot Get alerted to all of our Software updates on Twitter at @NeowinSoftware
    • Media Player Classic - Home Cinema 2.7.3 by Razvan Serea Media Player Classic - Home Cinema (MPC-HC) is a free and open-source video and audio player for Windows. MPC-HC is based on the original Guliverkli project (which is no longer maintained) and contains many additional features and bug fixes. As the continuation of the original Media Player Classic, MPC-HC isn’t flashy but it works with nearly any media format. MPC-HC uses DXVA technology to pass decoding operations to your modern video card, enhancing your viewing experience. And MPC-HC supports both physical and software DVDs with menus, chapter navigation, and subtitles. Overview of features A lot of people seem to be unaware of some of the awesome features that have been added to MPC-HC in the past years. Here is a list of useful options and features that everyone should know about: Dark interface Menu > View > Dark Theme When using dark theme it is also possible to change the height of the seekbar and size of the toolbar buttons. Options > Advanced Video preview on the seekbar Options > Tweaks > Show preview on seek bar Adjust playback speed Menu > Play > Playback rate The buttons in the player that control playback rate take a 2x step by default. This can be customized to smaller values (like 10%): Options > Playback > Speed step Adjusting playback speed works best with the internal audio renderer. This also has automatic pitch correction. Options > Playback > Output > Audio Renderer MPC-HC can remember playback position, so you can resume from that point later Options > Player > History You can quickly seek through a video with Ctrl + Mouse Scrollwheel. You can jump to next/previous file in a folder by pressing PageUp/PageDown. You can perform automatic actions at end of file. For example to go to next file or close player. Options > Playback > After Playback (permanent setting) Menu > Play > After Playback (for current file only) A-B repeat - You can loop a segment of a video. Press [ and ] to set start and stop markers. You can rotate/flip/mirror/stretch/zoom the video Menu > View > Pan&Scan This is also easily done with hotkeys (see below). There are lots of keyboard hotkeys and mouse actions to control the player. They can be customized as well. Options > Player > Keys Tip: there is a search box above the table. You can stream videos directly from Youtube and many other video websites You can stream videos directly from Youtube and many other video websites Put yt-dlp.exe or youtube-dl.exe in the MPC-HC installation folder. Then you can open website URLs in the player: Menu > File > Open File/URL You can even download those videos: Menu > File > Save a copy Tip: to be able to download in best quality with yt-dlp/youtube-dl, it is recommended to also put ffmpeg.exe in the MPC-HC folder. Several YDL configuration options are found here: Options > Advanced This includes an option to specify the location of the .exe in case you don't want to put it in MPC-HC folder. Play HDR video This requires using madVR or MPC Video Renderer. After installation these renderers can be selected here: Options > Playback > Output Ability to search for and download subtitles, either automatically or manually (press D): Options > Subtitles > Misc Besides all these (new) features, there have also been many bugfixes and internal improvements in the player in the past years that give better performance and stability. It also has updated internal codecs. Support was added for CUE sheets, WebVTT subtitles, etc. Media Player Classic - Home Cinema 2.7.3 changelog: Updated LAV Filters to version 0.82 Updated MPC Video Renderer to version 0.10.4.2550 Updated MPC Audio Renderer A few crash fixes, bug fixes and small improvements. Download: MPC-HC 2.7.3 (x64) | Standalone | ~20.0 MB (Open Source) Download: MPC-HC 2.7.3 (x86) | Standalone Links: MPC-HC Home Page | Screenshot Get alerted to all of our Software updates on Twitter at @NeowinSoftware
    • Microsoft will finally let you sign in to Edge with a Google account by Usama Jawad As things currently stand, Microsoft Edge only allows you to sign in to the browser with a Microsoft Account (MSA). This allows you to sync your browser settings and other data across other devices, as long as you sign in with the same account. However, Microsoft is now modifying this mechanism in a way that will likely please many users. In an update to its Microsoft 365 Roadmap, Microsoft has indicated that it will soon let users sign into Edge using a Google account from the profile menu and the Edge sign-in screen. This will be in addition to the MSA login option, and it opens up new doors for people who prefer using Edge, but cannot be bothered to configure a Microsoft account. This brings several advantages such as the ability to sync your data across devices using just a Google account. It may even facilitate flexible single sign-on (SSO) experiences where you can quickly login to websites and services through a single Google account that is presented as the preferred sign-in option. Up until now, Microsoft allowed customers to indirectly use a Google account, by configuring a Google account as a Microsoft account, or by setting up a one-way sync option between Edge and Chrome. This is a rather interesting development, especially considering that Google Chrome still limits you to a Google account sign-in, but it will be interesting to see if the company reciprocates Microsoft's gesture in the future. This is not the only recent instance in which Microsoft has extended a handshake to Google via Edge. In April 2026, it began tracking the development of a work search banner for Google Search queries, just like the one present in Edge. However, if we go back almost seven years, to January 2020, Microsoft had emphasized that it had no plans to "integrate Google services into Microsoft Edge by default", in response to people requesting Google sign-in services on Edge. Fast-forward to today, and Microsoft is planning to release this feature in July 2026, with IT admins having the option to control its availability on Windows and macOS through the NonMicrosoftAccountSignInEnabled policy.
    • If they ever come out and say the AI is no longer accessible to the gen pop people aren't going to know how to tie their own shoelaces.
  • Recent Achievements

    • One Month Later
      Vincian earned a badge
      One Month Later
    • First Post
      Jocimo earned a badge
      First Post
    • Week One Done
      suprememobiles48 earned a badge
      Week One Done
    • One Month Later
      Windows Guy earned a badge
      One Month Later
    • One Month Later
      Prasann earned a badge
      One Month Later
  • Popular Contributors

    1. 1
      +primortal
      509
    2. 2
      +Edouard
      172
    3. 3
      PsYcHoKiLLa
      89
    4. 4
      Steven P.
      76
    5. 5
      neufuse
      69
  • Tell a friend

    Love Neowin? Tell a friend!