Project: Macbook Tablet


Recommended Posts

@ulfses

Welcome to join the discussion here :) . I haven't try to make use of the internal usb ports yet...due to its final exam period right here.

But I planned to do that during the Christmas, where I got time and proper tools for it. Just because I hate the fact that the connection for the touch panel is sticky out.

thank you, thank you :)

It should be possible right? I was thinking about buying a keyboard cable, and split the leads off the cable, so if i mess it up - i wont destroy the logic board.

If it wont work, I will try to solder the touch panel to a very short usb plug i pulled of a non working flash drive and keep all the cables in the inside.

I also noticed two leads on the logic board next to the internal usb input, i tried to short circuit them - and it powered up. They seem a bit easier to reach if you just want a power button.

Just bought a G4 powerbook powerbutton from ebay that i will use. :)

I also plan to continue after Christmas due to exams - good luck!

Wow ulfses, very very nice work man. Keep us updated on the progress I cannot wait to see the finished product. I like the way you're retaining the LCD back case and building up from there, you might be able to use a particle board covering to finish up that edging if the CF overlay proves to hard to handle (like the covering they put on desks and benches). An added tip I can add is that while testing your power button, activate the "restart on power failure" or "wake on lan" feature just in case something doesn't work and you need to restart it.

I'm certainly interested in how hot it ends up getting in full use, as in high use I end up hitting about 80c.

I surly will keep you updated.

Regarding the CF skinning, I'm not sure how it would look if i skinned the whole case and then cut all the holes for the I/O, apple on the back and such. I imagine that i will risk that the white from the plastic or the wood will be visible and ruin the whole thing. I intend to enlarge every little opening with about 1mm (they say the carbon fiber add 1mm) and do some serious tailoring to fit the fiber through all the small kinks.

I just had some quality time with the keyboard ribbon to figure out the leads on it. Not sure if it will be easier to manipulate - but i made a simple schematic.

IMG_2171.jpg

my soldering skills is far from perfect - so the idea was that maybe isolating the leads from the ribbon would be easier. At least as i mentioned earlier - i wont bork my logic board.

I also thought about using some very small wires - position them in the socket on the logic board and stuff it with some molding paste to keep them from moving, but i guess it would compromise the connectivity.

I also have a sleep switch on paper that i will try to make later - i will keep you posted. I would never have thought about it if you haven't mentioned it earlier in the thread, thanks for that!

Its all the small things that count ;)

for a macbook, hitting 80c during normal operation is actually is "normal" range. I have been thinking about how to reduce the heat of it though, apparent unclocking the cpu would help a bit.

i have also notice the wifi card gets up to 7xc when its at full load.

And for ulfses, the power pins on the board, i have found them earlier but never took the time and risk to solder a new button on it.

but i dont know if its just my hands are not stable enough or what ever, i cant use those pins for a power reset after the "4 language" message board comes up saying i have to restart my laptop.

i tried a lot but it just wont work.

by the way, are you keeping your dvd drive on your tablet there? and what is that small battery pack you have at the lower right side of the tablet ?

And for ulfses, the power pins on the board, i have found them earlier but never took the time and risk to solder a new button on it.

but i dont know if its just my hands are not stable enough or what ever, i cant use those pins for a power reset after the "4 language" message board comes up saying i have to restart my laptop.

i tried a lot but it just wont work.

by the way, are you keeping your dvd drive on your tablet there? and what is that small battery pack you have at the lower right side of the tablet ?

I did see your post a bit to late :) Have you tried to use the reset pins that are next to the ram-slot on the edge? Its probably safer to figure out a way to connect cables to the internal usb.

The battery pack is one one out of three thats in the macbook battery. The battery i had was long gone, so i pulled it apart to get an impression of how much space i needed. I will pull the packs out of the new battery as well.

I save some space and I can make room for the more easily.

I'm not keeping the dvd drive. No space and I never really use it.

Yesterday i made a switch for the sleep mechanism as well. It turned out great. :D

  • 2 weeks later...

Can't remember who gave the 3M link (and of course I'm too lazy to go back and figure it out), but that capactive screen looks promising. On 3M's touch screen drivers page, the Mac OS X link takes you offsite to a company called "Touch Base". The driver has been updated as recently as this November, which is also promising...

I've got a Mid '09 Macbook Air that I plan to tablet-ize, and all the info from this thread is much appreciated!

Can't remember who gave the 3M link (and of course I'm too lazy to go back and figure it out), but that capactive screen looks promising. On 3M's touch screen drivers page, the Mac OS X link takes you offsite to a company called "Touch Base". The driver has been updated as recently as this November, which is also promising...

I've got a Mid '09 Macbook Air that I plan to tablet-ize, and all the info from this thread is much appreciated!

yeah, it looked really nice. The only problem is the price really, i think its 200$+

found this - capacitive panels - but they dont have the 13" in stock.

yeah, it looked really nice. The only problem is the price really, i think its 200$+

found this - capacitive panels - but they dont have the 13" in stock.

LG has a 13.3" touch screen in development with sensors actually "built into the display" (I can't find anywhere that specifies what exactly that means, other than they're not using a film overlay). Note that the press release is from February and touts a 2nd half of 2010 release - but it's still in development. Saw a more recent LG press release that touted the technology, but no firm release date. I'll be keeping my eyes peeled for a date & driver availability.

Speaking of price - I'm just in this for the fun. If the panel alone costs $200-$300, so be it...

I have been looking for news about 13.3" capacitive panels every other week since this summer, and it seems like there is not a very big market - yet.

I agree that a price over 200$ dont justify such a project. Maybe a 8wire resistive screen would be cheaper - I believe they support multitouch with the correct drivers. Im gonna try ubuntu's new netbook edition with the resistive panel i bought and see if it will recognize gestures. That would be nice.

I have used the 3m touch screen been having some issues getting the calibration right. I am going to try a new driver today hopefully that fixes the problem.

I also need to figure out a little problem I am having with charging. I think it might be my charger but no way to know for sure...

solved all the issues my capacitive touch screen and the charging ones. It is now in perfect working condition and highly highly responsive. Now I just need a driver set that is a full version and not restricted to a 100 mouse clicks or finger touches...

touch screen was $150

let me know if you guys want to know where to get the screen

  • 3 months later...
  • 1 month later...

I think I'm going to toy with the idea again of doing this to either a MacBook or Mac Book Air ..... anyone see any articles of someone attempting this with a MacBook Air .... so far still can't find anything.

Thanks again "enigma-penguin", this was an awesome project to read up on!!

:cool:

  • 3 months later...

Don't know if there's any interest left in this thread, but thanks a million to Matt for posting all the information and photos, it helped me immensely with my project: a touchscreen MacBook. My version is not a tablet, (yet) but simply an A1181 type white MacBook with a resistive touchscreen overlay incorporated into the screen. I found the best way to do this was to take the plastic bezel cover and cut out the material to exactly fit around the glass. This way the overlay does not add any thickness.

The donor MacBook is a collection of parts. I repair MacBooks as a side job so parts are always available to me. The heart is an early 2009 MacBook. 2.0 GHz Core 2 Duo with a 1066 MHz bus. Altough the RAM is only 667 MHz, there is 4 GB. The HDD is only 80 GB for now (7200 RPM), although an SSD may be in the future. I do have room for a second HDD (keep reading) and this Logic Board has a second SATA connector on it which can be adapted to fit a HDD. Besides that it has all the stuff a MacBook should, plus the stuff Apple doesn't give you anymore like optical audio in/out, FW400, and ethernet.

The MacBook doesn't look that different on the outside, apart from the visible green border around the touchscreen. The weight is about the same, the DVD drive was removed to make room for some other stuff, but the overlay has a substantial piece of glass. I could not find a thin version in the right size.

It's not without some bugs right now, The removal of the DVD drive was not by choice, although I won't miss it. I needed the extra space to fit the touchscreen controller. I tried fitting it every other place but there wasn't room. With the DVD drive gone I had a lot of extra space to work with, so I decided to put in a USB hub. This would compensate for the loss of one USB port on the left for the touchscreen. (For the tablet version I will probably use the keyboard bus.) Now the MacBook has one USB port on the left, and 3 on the right. I discovered that the USB ports on the left are not the same. The back port next to the FW400 is actually connected to a hub internally. Connecting this to another hub just doesn't work. Currently the front USB port is connected to wires running under the logic board to the 4 port hub on the right. One port is used by the touchscreen and three are available. Power for the hub is provided only by the USB port, and the power for the touchscreen is borrowed from the fan. I did this because I want all the power possible available to devices on those ports. This project required throwing out all the included connectors and soldering everything to save space.

The next step is finding an elegant way to disconnect or deactivate the internal keyboard on command, so as to eliminate accidental trackpad input when drawing. Also, cleaning it up cosmetically on the left side USB ports. If I build another version it will be a full tablet.

post-410626-0-85706300-1314780435.jpg

post-410626-0-56948300-1314780475.jpg

post-410626-0-33111800-1314780484.jpg

post-410626-0-85463800-1314780496.jpg

post-410626-0-05554900-1314780507.jpg

post-410626-0-49316200-1314780517.jpg

I honestly don't see the appeal in having a vertical touch screen; there's just nothing practical about it, not to mention it's pretty much pointless for any serious amount of work you'd be doing on a Wacom tablet for example. It's still neat you took the time to make your own mod, although it would have been much cooler if you invested more in the overall fit-'n'-finish.

I honestly don't see the appeal in having a vertical touch screen; there's just nothing practical about it, not to mention it's pretty much pointless for any serious amount of work you'd be doing on a Wacom tablet for example. It's still neat you took the time to make your own mod, although it would have been much cooler if you invested more in the overall fit-'n'-finish.

Its a pet project. It's not done either. If it stays a laptop I'll clean up the USB or find a different solution. If it evolves to a tablet, I won't need them anyway and I'll replace the bottom case.

Excellent to see how far you have gone with the project so far, I know it's probably going to be a long road to making it a tablet if you ever really do want that in the end. I must admit that it's nice to see people doing projects and doing more with their macs, keep us up to date on what you decide on!

Honestly man, keep up the good work :)

  • 3 months later...
This topic is now closed to further replies.
  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Posts

    • They thought value of their goods would forever only drop like it used to and didn't account for sudden increase in price because of all the Ai hype. Tough luck Samsung, don't try to weasel this one out. Also American customer protection laws are a**. In Europe, you need to be compensated for a functioning product of same or better characteristics (not same price point as when it was originally bought!) if it can't be repaired and when you receive a replacement product your warranty starts from scratch because you received a different item than you previously had and old warranty thus cannot apply to it anymore. If your actual item was successfully repaired, warranty gets extended for the period the item was in service. If item is repaired to a significant extent, warranty also starts over from scratch because major part of it was replaced. Americans need to fight to get this kind of consumer protections because they are constantly getting screwed over.
    • Microsoft releases new Windows 11 Media Creation Tool with the latest updates by Taras Buria Patch Tuesday updates arrive every month, bringing users new features and security updates. To make sure customers have access to the most recent images, Microsoft also releases updates to the Media Creation Tool app, its official utility for Windows 11 installation. Today, the company pushed new ISOs to Media Creation Tool, allowing you to create images with the June 2026 Patch Tuesday updates. With the latest update, the Media Creation Tool now downloads KB5094126. It is Windows 11 version 25H2, build 26200.8655, which is also available via Windows Update. Note that the app itself remains on the previous version, which you can check in Properties > Details. The only change is that it now downloads a more recent Windows 11 build, so the only way to check is to download an ISO. The June 2026 Patch Tuesday update is a special release for Windows 11, as it brings a new performance profile to make the operating system more responsive and snappier when rendering various user interface surfaces, including the Start menu, quick settings, and more. It does so by spiking processor speeds for a brief moment, resulting in higher loads for a second or two. The so-called “Low latency profile” is rolling out gradually, but you can force-enable it with the ViVeTool app. Other changes include webcam improvements, Task Manager updates, shared audio support, and more. You can download the Media Creation Tool app from the official Microsoft website using this link. Besides MCT, Microsoft lets you download Windows 11 ISO as a file directly from the official Windows 11 website. However, you will need a third-party app to write it to your USB drive. Check out this guide if you want to know how to do that.
    • Louis Rossmann suing Samsung over "990 Pro SSD warranty scam" by Sayan Sen Back in 2023, if you recall, Neowin reviewer Robbie Khan had a dispute with Samsung over his 990 Pro SSD, which was rapidly losing its health. After significant back and forth, the tech giant had finally released firmware to "stop" the issue. Interestingly, its previous flagship at the time, the 980 Pro was also facing problems leading to two consecutive sets of firmware fixes. Three years later, it looks like a similar conflict has now broken out between tech repair entrepreneur YouTuber Louis Rossmann and Samsung, as it has escalated into a threatened lawsuit after the company allegedly refused to appropriately replace a failing 990 Pro SSD that remained under warranty. According to Rossmann, a 4TB Samsung 990 Pro NVMe SSD purchased for approximately $330 less than two years ago, began experiencing major hiccups and issues, even though he claims it had been operated under ideal cooling conditions. It was installed in a RAID 1 array and cooled by a heatsink and dual high-speed fans. However the drive reportedly started dropping out of the array, exhibiting controller-level failures that eventually became not useable in any meaningful way. Rossmann said Samsung’s support process was marked by delays and confusion from the very start. After initially contacting the wrong regional support channel, he was redirected to Samsung’s memory support division where he submitted detailed diagnostics, logs, and proof of purchase. Rossmann runs a repair company and owns an ACE Lab PC-3000 machine, which is a professional-grade data recovery equipment. As such, he had been confident in his diagnostics. Samsung even seemingly acknowledged that later. Regardless, Rossmann claims that his initial support ticket was automatically closed before a full 24-hour response window had elapsed, forcing him to reopen the case and resubmit documentation. The controversy however intensified further from here after Samsung accepted the drive for warranty evaluation but later returned it with a repair report stating that the drive had passed its testing and that the SSD had been verified as functional. Rossmann strongly disputed those claims citing that his own independent testing on PC-3000 showed write speeds reducing to as low as 40–60 MB/s before the drive failed entirely. Samsung subsequently informed him that the SSD had been reset and reflashed, passing internal stress tests. However, the company also stated that replacement units were unavailable due to an industry-wide memory shortage and suggested that a refund process could be initiated if further testing confirmed the fault. Thus, to settle, the company offered a refund of $330, the amount that was initially paid by him to make the purchase. Here, Rossmann pointed out the seeming hypocrisy of the tech giant as in how no Samsung drive was apparently allocated for warranty replacements, but they were abundantly available for retail sales especially when using business accounts. As you can see, Rossmann is indeed right, there are Samsung 990 Pro 4TB SSDs on Amazon currently for $950 (shipped and sold by first-party Amazon US itself), and they are also available on Samsung's own store too, albeit for an even higher price of $1100. Thus Rossmann argues that Samsung’s inability or unwillingness to provide a replacement while the same model remains available for purchase at significantly higher market prices reflects a failure to honor its warranty obligations. He has issued a formal 60-day notice and says he intends to file suit in Texas small claims court, asserting that companies should face greater costs for denying legitimate warranty claims than for fulfilling them. You can check out the full video titled "Samsung's 990 Pro SSD warranty policy is a scam; I'm taking them to court," at the link below. Source and image: Louis Rossmann (YouTube) As an Amazon Associate we earn from qualifying purchases
    • Was it too much to ask to show the icon in this article?
  • Recent Achievements

    • Week One Done
      davidbazooked earned a badge
      Week One Done
    • One Month Later
      Jamswaz earned a badge
      One Month Later
    • Week One Done
      Jamswaz earned a badge
      Week One Done
    • Rookie
      Marzoid went up a rank
      Rookie
    • Community Regular
      coch went up a rank
      Community Regular
  • Popular Contributors

    1. 1
      +primortal
      509
    2. 2
      PsYcHoKiLLa
      184
    3. 3
      +Edouard
      158
    4. 4
      Steven P.
      83
    5. 5
      ATLien_0
      75
  • Tell a friend

    Love Neowin? Tell a friend!