(FIX) Windows 7 SP1 not waking from sleep mode


Recommended Posts

Before I installed Windows 7 Service Pack 1, my sleep mode was working fine with no problems. When SP1 was installed I could put the computer into sleep mode, but it wouldn?t wake up. It would also not wake up if the computer went into sleep mode as per the power settings of 20 minutes of non-usage.

I had to play around with the power options and came up with the following that appears to now be working:

Open control panel and go to

Power Options > change plan settings in the preferred plan options > Advanced Power Settings

+Sleep

Allow hybrid Sleep > OFF

Allow wake timers > enable

+USB

USB selective suspend > ENABLE

+Multimedia Settings

+When Sharing media [This is the critical one]

Set to allow the computer to sleep.

Click apply and ok and that should do it.

It worked for me I hope it works for you.

Ok just set up my power plan as guided..... fingers crossed this works, before doing this, I would get full fan speeds only, and no waking up when I tried.

Here goes...

EDIT - I guess the fact I just had to turn the PSU off at the back because the power buttons didn't work and the system fans were at full speed shows this didn't fix it for me

Before I installed Windows 7 Service Pack 1, my sleep mode was working fine with no problems. When SP1 was installed I could put the computer into sleep mode, but it wouldn�t wake up. It would also not wake up if the computer went into sleep mode as per the power settings of 20 minutes of non-usage.

I had to play around with the power options and came up with the following that appears to now be working:

Open control panel and go to

Power Options > change plan settings in the preferred plan options > Advanced Power Settings

+Sleep

Allow hybrid Sleep > OFF

Allow wake timers > enable

+USB

USB selective suspend > ENABLE

+Multimedia Settings

+When Sharing media [This is the critical one]

Set to allow the computer to sleep.

Click apply and ok and that should do it.

It worked for me I hope it works for you.

Just wanted to bump this and mention that I had the same problem, and the suggestion to disable hybrid sleep is what fixed it. As a bonus, the system also goes into sleep MUCH faster.

I never needed hybrid sleep anyway, it was just a default. Thanks for the tip!

This actually happens to me, before SP1 my PC use to be able to go to sleep and return from sleep. After SP1 it may go to sleep but everything is still wuring and the monitors just turn off (you have to hold down the power button to turn it off).

I will try this when I get home, thanks!

My sleep works the same as it did pre-SP1...I hate when the computer wakes up automatically because of scheduled tasks (namely Window Media Center update related). Granted it does go back to sleep when it's done (usually around 4-5 minutes).

  • 2 weeks later...

got same issue but the above is not fixing it for me, now considering uninstalling SP1, as the machine in question is a media center operated from an armchair, i'm way too lazy to get up, open a cupboard and push the power button to wake my machine

anyone any other ideas?

  • 3 months later...

Just wanted to say that for me and many other people, the above mentioned solution did not work.

It turns out that for many users, the problem is actually a compatibility issue between Internet Explorer 9, and Skype versions 5+.

Problem: After installing Windows 7 SP1, entering sleep/hibernate mode causes PC to hang for an extended period, and then bluescreen.

I tried all of the following, and NOTHING worked:

- Installed Win7 Hotfix KB2495523

- Disabled "Allow hybrid sleep" in power options

- Installed newest version of real-tek ethernet driver

- Disabled "Allow Wake Timers" in power options

- Set JavaScript Timer Frequency -> Maximum Power Savings in IE power options

SOLUTION

There are currently 2 solutions:

1. Uninstall Skype v5, and roll back to version 4. (Version 4.2.0.187 confirmed working)

or

2. Uninstall Internet Explorer 9 (Windows Update --> Installed Updates --> IE9, Uninstall)

Skype Bug Report: https://jira.skype.com/browse/SCW-2796

NOTE:

Another option is to simply close Skype before entering sleep mode.

Confirmed that the newest version of Skype that does not lead to the crash when IE9 is installed is Version 5.0.0.156. Reverting back to 5.0.0.156 fixes the issue.

http://www.oldapps.com/skype.php

I think my issue stems from when Windows tries to switch automatically from sleep mode to hibernate mode. My power light is steady/on (it blinks when it's in sleep mode), the fan is running, but whenever I try to do something, it just sits there.

  • 1 month later...

Before I installed Windows 7 Service Pack 1, my sleep mode was working fine with no problems. When SP1 was installed I could put the computer into sleep mode, but it wouldn?t wake up. It would also not wake up if the computer went into sleep mode as per the power settings of 20 minutes of non-usage.

On my Toshiba Satellite L655D-S5050, not only did SP 1 make it impossible to put the computer to sleep, or hibernate, but when it shut off I couldn't get it to wake up. There were not even any indicator lights on the front panel when plugged into the power supply. I finally figured out that if I disconnected the power supply, removed the battery, then re-connected the power supply, I could get it to come back to life. I was so relieved to get the computer to come back to life, that I didn't want to even try to get it to work with SP1 that I simply uninstalled SP 1. I saw no particular benefit, only problems, so I'll live without it until the good people at Microsoft re-issue it without the rather serious bugs. I looked for a solution with Toshiba, but, typically, there was none.

This topic is now closed to further replies.
  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Posts

    • FotoSketcher Studio 4.30 by Razvan Serea FotoSketcher Studio is a free creative tool that instantly turns your photos into artwork. With just a few clicks, you can apply styles like pencil sketches, watercolor, oil painting, ink drawings, cartoons, and abstract effects. Powerful yet simple sliders let you adjust every detail to match your vision, from subtle enhancements to bold artistic transformations. You can also improve your images with tools for contrast, sharpness, color, and brightness, plus add frames and text. It supports JPEG, PNG (including transparency), BMP, and WebP formats for both opening and exporting. Available for Windows (64-bit) and macOS (Apple Silicon and Intel), FotoSketcher also offers batch processing, manual retouching, and custom effects for advanced users. Completely free, including commercial use, with no ads or spyware. FotoSketcher Studio 4.30 changelog: New LUTs effect In the Photo Lab category you will find a new LUTs (Lookup Tables) effect for custom colour grading. It comes with 18 presets built right into the application (Cinematic, Kodachrome, Golden hour, Portrait and more), each with a live preview so you can see the look before applying it. Right-click the preview to compare with your original image. And if you have your own .cube files, you can load those from disk too. New "Stylize" category Added a brand-new Stylize category with four new effects. Three of them (Mosaic, Circles and Triangles) are built on the same space-filling idea, turning your photo into tiled mosaics, clusters of circles, or a low-poly triangle look. The fourth, Cartoon, is a bit different: it gives a clean graphic style with defined lines and solid colours. A little tip - set the colour intensity to 0 and Cartoon draws a pure outline drawing with no fill. Combined with the "Do not erase background" option, you can run it on top of any other effect to add crisp contours in two quick steps. Auto-Enhance and Full Reset Two small but handy additions. Auto-Enhance (just press E) tries to optimise your source photo - exposure, white balance, local contrast - for a 'dehazed', natural-looking starting point. And Full Reset clears everything back to a clean slate in one step (working image, history, LUT, script, brushes and sliders) without having to close and reopen the program. Press Ctrl+Shift+N, or right-click the exit button. Scripts The script engine has been updated to support all the new effects, with a few new commands and improved help. If you would like some inspiration, the recent scripting tutorial on this blog walks through several ready-made example scripts. The usual improvements The interface now uses new colour accents for better readability, the history gallery has had a few tweaks, and you can now open .webp images directly. On top of that, this release includes some performance improvements and a good number of bug fixes. Download: FotoSketcher Studio 4.30 | 55.9 MB (Freeware) Download: FotoSketcher Studio for macOS | 119.0 MB View: FotoSketcher Website | Screenshot Get alerted to all of our Software updates on Twitter at @NeowinSoftware
    • I have a Motorola, one of the lower end ones, it works fine. It is possible to get rid of the Gemini app and also to disable googles assistant , but A.i is still apps. I try to avoid all LLM A.I, is i can, I use no Ai duck duck go.
  • Recent Achievements

    • Conversation Starter
      sumytbe earned a badge
      Conversation Starter
    • One Year In
      B4dM1k3 earned a badge
      One Year In
    • One Year In
      DarkWun earned a badge
      One Year In
    • Dedicated
      Almohandis earned a badge
      Dedicated
    • Dedicated
      JuvenileDelinquent earned a badge
      Dedicated
  • Popular Contributors

    1. 1
      +primortal
      519
    2. 2
      +Edouard
      189
    3. 3
      PsYcHoKiLLa
      87
    4. 4
      Michael Scrip
      81
    5. 5
      Steven P.
      72
  • Tell a friend

    Love Neowin? Tell a friend!