BASED ON EXPERIENCE which is more comfortable X360 controller or DualShock


BASED ON EXPERIENCE, which is more comfortable?  

203 members have voted

  1. 1. BASED ON EXPERIENCE, which is more comfortable: Xbox 360 controller or DualShock 3?



Recommended Posts

i have two of those with the docking station and they have been going for 5 years strong and work as good as the day i bought them...

That's what I was told: they charge if you buy a dock or charge station, but I find that to be inconvenient. They were charging OK for a whole year just connecting the controller with the usb cable, after that they would seem to be charging but even while the light went green they died in a couple of seconds after unplugging the cable.

The play and charge kit is a NiMH battery pack, so most people who have issues with them most likely do because the charge them wrong.

What do I have to do to charge them right?

Looks like there are too many MS fanboys here. IMO Sony controller is much more accurate and sensitive. I hate the R2 L2 in the 360 controller and the lack of USB rechargeable battery. MS might be the leader in software but Sony rules in Hardware..

The play and charge kit is a NiMH battery pack, so most people who have issues with them most likely do because the charge them wrong.

What do I have to do to charge them right?

Yeah, most NiMH batts have issues if you don't run then to flat/near flat (under 20%ish) and then charge them fully in one go to 100%...if you do small charges for say an hour or charge it when its still got a decent ammount of charge left, they'll lose the ability to hold charge over time.

Best bet (and what I do) is to run it flat...or at least until the 1st controller auto shutoff, then plug it into my PC or a USB mains adapter (iPhone charger or similar) as these are left on...this way the controller gets a 100% charge rather than a semi-chrage from the hour or 2 I'm playing my xbox...I've had my play and charges for 3 years both still work fine...I'd guess I get at least 10 hours from 1 charge.

Yeah, most NiMH batts have issues if you don't run then to flat/near flat (under 20%ish) and then charge them fully in one go to 100%...if you do small charges for say an hour or charge it when its still got a decent ammount of charge left, they'll lose the ability to hold charge over time.

Best bet (and what I do) is to run it flat...or at least until the 1st controller auto shutoff, then plug it into my PC or a USB mains adapter (iPhone charger or similar) as these are left on...this way the controller gets a 100% charge rather than a semi-chrage from the hour or 2 I'm playing my xbox...I've had my play and charges for 3 years both still work fine...I'd guess I get at least 10 hours from 1 charge.

See, at that rate, you may as well buy a charger with batteries, charge all 4, use 2, have 2 on hand to change over when the other 2 die and then charge the dead ones.

A charger with 4 rechargeable batteries is also probably cheaper than that kit. And less of a hassle.

i have two of those with the docking station and they have been going for 5 years strong and work as good as the day i bought them...

Cool story. Sorry, I am all out of Gold Stars.

The play and charge kit is a NiMH battery pack, so most people who have issues with them most likely do because the charge them wrong.

Every single time I charged them because they were dead/almost dead. Would let it go until I got the message from the console about my battery being low.

How else is one supposed to charge batteries?

Because if that is wrong, then I have to say NiMH are not very good, as I do the same thing with the DS3 controllers, wait until they blink, and I am on my same controllers since launch.

I literally have 4 of them. 2 are useless. Even purchased the charging dock hoping it would help.

And let me add, since I have owned the 360, I have also owned no less than 5 other devices that have rechargable batteries.

DS3 being one of those items, iPad, iPhone, 2 Macbook Pros, 1 HP Laptop, countless iPods, 2 Droid phones, a PSP, now a Vita, a DS, and none of these other devices ever had the same issues I have had with the 360 plug and play batteries. If somehow these fancy NiMH batteries operate in a different one than all of these other devices, then not sure what to say other than perhaps they should have incorporated batteries like these other devices. If some of these devices do operate the same way, then not sure what to say other than the ones used for the 360 plug and play must not be the greatest.

Personally I prefer the DS3 controller because of the joysticks' position and convex nature (I use the flatter parts of my thumbs to control the joysticks rather than the tips). Also, I find the controller more comfortable due to it's symmetrical design and ease of d-pad use.

The advantages of the DS3 controller are the easy-to-control d-pad, primary buttons (cross, square, triangle, and circle) being on a flat plane, and the light, symmetrical design.. The drawbacks of using the DS3 controller are the convex triggers and it's small handle architecture making it a bit of a jump from holding an xbox controller. The advantages of the xbox controller are it's ergonomic design and the trigger buttons (joysticks and d-pad positions are personal preference); disadvantages include primary button positions (a, b, x, and y) and how they wrap around the controller and the sloppy d-pad.

I own both an xbox 360 and a ps3 and use both frequently. Remember to take all of these opinions with a grain of salt. Might I suggest you hold one of each controller (either at a friend's house or best buy, etc.) so that you can get a feel for each?

Looks like there are too many MS fanboys here. IMO Sony controller is much more accurate and sensitive. I hate the R2 L2 in the 360 controller and the lack of USB rechargeable battery. MS might be the leader in software but Sony rules in Hardware..

Fanboys because we think the Xbox controller is better? All of my mates who have PS3s prefer the Xbox controller over it, are they fanboys too champ?

Fanboys because we think the Xbox controller is better? All of my mates who have PS3s prefer the Xbox controller over it, are they fanboys too champ?

Did you admit to being a fanboy earlier?

Cool story. Sorry, I am all out of Gold Stars.

or you can sound like a butt hurt child because i added my personal experience with said gaming accessories the OP is asking about... :cry:

If somehow these fancy NiMH batteries operate in a different one than all of these other devices, then not sure what to say other than perhaps they should have incorporated batteries like these other devices.

They do, since all those other devices use lithiun( io to be exact) batteries.

And lithium batteries would have been preferable, but then they'd probably have to make them non removable for safety. Which is a crap design and against regulations.

And lithium has its own problems, like limite charge cycles (about 300), dying if they go flat, not to mention the explosive power.

Did you admit to being a fanboy earlier?

Massive XBOX, Android and Windows fanboy.

I admit it though. What I don't get is others being labelled fanboys just because of their opinion.

Massive XBOX, Android and Windows fanboy.

I admit it though. What I don't get is others being labelled fanboys just because of their opinion.

I think there is a difference between being a hopeless fanboy who would side with their preferred device regardless of any alternatives or info and someone who honestly prefers something. I guess sometimes it is just hard to differentiate the two. And, let's be honest, most people wouldn't try. Labels are much easier.

Yeah, most NiMH batts have issues if you don't run then to flat/near flat (under 20%ish) and then charge them fully in one go to 100%...if you do small charges for say an hour or charge it when its still got a decent ammount of charge left, they'll lose the ability to hold charge over time.

Best bet (and what I do) is to run it flat...or at least until the 1st controller auto shutoff, then plug it into my PC or a USB mains adapter (iPhone charger or similar) as these are left on...this way the controller gets a 100% charge rather than a semi-chrage from the hour or 2 I'm playing my xbox...I've had my play and charges for 3 years both still work fine...I'd guess I get at least 10 hours from 1 charge.

Hmm then it's weird. I've always plugged them when the controller stopped working, and kept them plugged until the light went green.

Also I didn't even plug them to the Xbox but to the usb port of my desktop PC so they kept getting juice even if I wasn't playing (and because the front xbox usb ports are annoying to plug to). I do the same with both of my DS3.

I don't know if it might be relevant, but they stopped recharging after I got my Xbox back from MS technical service. The DVD tray wasn't reading any media so I sent the console to get that repaired, and after getting it back I kept the console in the box unused for several months.

Do those batteries go bad if you don't use them for a long while?

See, at that rate, you may as well buy a charger with batteries, charge all 4, use 2, have 2 on hand to change over when the other 2 die and then charge the dead ones.

A charger with 4 rechargeable batteries is also probably cheaper than that kit. And less of a hassle.

Yeah but I find the Play and Charge kits last longer that AA's for me...even If I use NiMH AA's

They do, since all those other devices use lithiun( io to be exact) batteries.

And lithium batteries would have been preferable, but then they'd probably have to make them non removable for safety. Which is a crap design and against regulations.

And lithium has its own problems, like limite charge cycles (about 300), dying if they go flat, not to mention the explosive power.

Exactly, Nickel Metal Hydride (NiMH) batteries work differently to Li-ION batteries (what's in most laptops and iDevices)...

Li-ION also provides a lot more power...this is why its used in high consumption devices like laptops smartphones and tablets...an xbox controller doesn't need that much power so they opted for NiMH

Also Li-ION is also a lot more expensive than NiMH.

Do those batteries go bad if you don't use them for a long while?

Yeah NiMH will lose about 30% charge per month, Li-ION about 2-3% per month.

Did a bit more reading, and the method for charging batteries that I said earlier is best for Li-ION

NiMH idealy should be fully discharged before charging, and a lot of the NiMH chargers you buy will have a discharge function...(my Uniross one does)

source:http://batterydata.com/

Controller S for Xbox 1 :D. Nah, in all seriousness, I've had a PS1, PS2 and used a DS3 before. Xbox 360 is hands-down without a shred of doubt, better. But my first statement still stands true, that was the best during xbox 1 era.

Wow, then I think I won't be buying a xbox battery pack ever again :s

I think he's mis quoting quite bad, or you're misunderstanding his quote.

If you charge the battery fully and then leave it alone it will lose 30% of it's "charge" every month. However, a NiMH battery is very little affected by age, whereas age and charge cycles is the primary reason for capacity reduction on Lithium. NiMH batteries primarily lose capacity from wrong usage. And even when they've gone bad, they can often be revived to higher capacity by cycling. though it's hard on these kind of batteries or without a special charger,

I've got both a PS3 and a 360 and have no allegiance to either.

360 controller is far, far superior to the old fashioned dual shock. Both in terms of comfort and responsiveness.

Oh and NimH batteries all the way. Those battery packs are rubbish - not only do they last only a few hours after a few months of heavy uses, but I've had to replace two of them because they would no longer charge.

I think he's mis quoting quite bad, or you're misunderstanding his quote.

If you charge the battery fully and then leave it alone it will lose 30% of it's "charge" every month. However, a NiMH battery is very little affected by age, whereas age and charge cycles is the primary reason for capacity reduction on Lithium. NiMH batteries primarily lose capacity from wrong usage. And even when they've gone bad, they can often be revived to higher capacity by cycling. though it's hard on these kind of batteries or without a special charger,

Ah ok, that's far more reasonable :D

What was I doing wrong? I always charged them fully (through the usb cable, with the battery attached to the controller) and used them until the controller stopped working.

I think I'll rather keep playing with the usb cable instead of spending money on new batteries or trying to fix these ones, but learning how to do things right never hurts :blush:

This topic is now closed to further replies.
  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Posts

    • Ocenaudio 3.19.3 by Razvan Serea  Ocenaudio is a full featured, fast and easy to use audio and music editor. It is the ideal software for people who need to edit and analyze audio files without complications. Ocenaudio also has powerful features that will please more advanced users. To assist ocenaudio development, a powerful toolset of audio editing, analysis and manipulation called Ocen Framework was created. ocenaudio is also based on Qt framework, a well known library for cross-platform development. Cross-platform support ocenaudio is available for all major operating systems: Microsoft Windows, Mac OS X and Linux. Native applications are generated for each platform from a common source, in order to achieve excelent performance and seamless integration with the operating system. All versions of ocenaudio have a uniform set of features and the same graphical interface, so the skills you learn in one platform can be used in the others. VST plugins support Ocenaudio supports VST (Virtual Studio Technology) plugins, giving its users access to numerous effects. Like the native effects, VST effects can use real-time preview to aide configuration. Real-time preview of effects Applying effects such as EQ, gain and filtering is an important part of audio editing. However, it is very tricky to get the desired result by adjusting the controls configuration alone: you must listen the processed audio. To ease the configuration of audio effects, ocenaudio has a real time preview feature: you hear the processed signal while adjusting the controls. The effect configuration window also includes a miniature view of the selected audio signal. You can navigate on this miniature view in the same way as you do on the main interface, selecting parts that interest you and listening to the effect result in real time. Multiselection for delicate editions To speed up complex audio files editing, ocenaudio includes multi-selection. With this amazing tool, you can simultaneously select different portions of an audio file and listen, edit or even apply an effect to them. For example, if you want to normalize only the excerpts of an interview where the interviewee is talking, just select them and apply the effect. Eficient edition of large files With ocenaudio, there is no limit to the length or the quantity of the audio files you can edit. Using an advanced memory management system, the application keeps your files open without wasting any of your computer's memory. Even in files several hours long, common editing operations such as copy, cut or paste happen almost instantly. Fully featured spectrogram Besides offering an incredible waveform view of your audio files, ocenaudio has a powerful and complete spectrogram view. In this view, you can analyze the spectral content of your audio signal with maximum clarity. Advanced users will be surprised to find that the spectrogram settings are applied in real time. The display is updated immediately when altering features such as the number of frequency bands, window type and size and dynamic range of the display. Ocenaudio 3.19.3 changelog: Fixes issues with MP4 files with more than 8 channels Fixes incorrect VBR detection for some CBR MP3 files Other bug fixes and improvements Download: Ocenaudio 64-bit | Portable | ~40.0 MB (Freeware) Download: Ocenaudio for Linux and Mac OS View: Ocenaudio Homepage | Screenshot Get alerted to all of our Software updates on Twitter at @NeowinSoftware
    • DiskGenius 6.2.0.1829 - All Versions: Free, Lite & Portable by Razvan Serea DiskGenius is a full-featured partition manager, which is designed to optimize disk usage for Windows users. It will efficiently help you recover lost data, resize/split partition, backup files, edit hex data, check bad sectors, manage virtual disks, erase data, etc.. Create a system image backup for current Windows with simple clicks to keep the operating system under protection. DiskGenius key features: Partition Management - It can create format, resize, extend, backup, split, hide and clone partition, both MBR and GPT are supported. Disk and partition conversion - Convert dynamic disk to basic, convert virtual disk format and convert MBR to GPT, convert primary partition to logical. File recovery - It can recover files deleted or emptied form recycle bin, recover files from damaged partition or disk and recover files by file type and supports file preview and file filter. Partition recovery - It is the best partition recovery program in that it can recover files from damaged, corrupted and RAW partitions, search for lost partition and recover files from it, besides, it can fix partition table. RAID recovery - It can reconstruct Virtual RAID and recover files from it, and all RAID types are supported. Sector Editor - A Hex editor is embedded to help users edit raw hex data and recover data manually. Backup and Restore - It can backup and restore partition including system partition, hard disk and partition table. Bad Tracks - It can check and repair bad sectors for all storage devices; check hard disk S.M.A.R.T. information. Delete files permanently - It can delete files permanently so that they can't be recovered by any data recovery software. Virtual Disk - It supports virtual disks, including VMware, Virtual PC and Virtual Box. Create WinPE bootable disk and you can manage disk partition when system crashes or there is no operating system on your computer. Support FAT12/FAT16/FAt32/exFAT/NTFS/EXT2/EXT3/EXT4 file system format. DiskGenius 6.2.0.1829 changelog: Add the "Disk Speed Test" feature. Add the "Windows Boot Repair and Conversion" feature. Add the BMB21-2019 erase standard to the "Erase Sectors" feature. Add support for restoring an individual partition from a PMFX disk image file. Enhanced The "Verify Or Repair Bad Sectors/Blocks" feature displays disk read speed in the detection window during scanning. The "Quick Partition" dialog box allows users to quickly select the number of partitions by pressing the numeric keys 1, 2, 7, 8, or 9. The "Set Volume Name" dialog box supports selecting preset volume labels provided by the software. The "Copy Sectors" feature supports resuming copy tasks after modifying the number of skipped bad sectors. Add the "TRIM Optimization" option to the format dialog box. The "Clone Partition" and "Clone Disk" features perform TRIM optimization on target partitions or disks before cloning. Add support for Not Equal To search conditions (prefixed with "!") when searching hexadecimal data in the sector editor. Optimize the display of capacity values in the program interface to show two decimal places. Add a minimize button to dialogs that may require long processing time. Enhance support for the ReFS file system. Enhance support for newer HIF and MP4 formats when recovering files by type. Enhance support for the EXT4 file system. Enhance compatibility of the "File Recovery" feature with special data structures. Fixed Fixed the issue that the selected file system type automatically reverted to NTFS after changing it to exFAT or EXT4 in the "Quick Partition" dialog box. Fixed inaccurate Unicode string search results in the "Sector Editor" feature. Fixed the issue that exceptions might occur when adding multiple disks in the "Erase Sectors" feature. Fixed the issue that insufficient target disk space was incorrectly reported in some cases when cloning, backing up, or restoring disks. Fixed the issue that folder modification timestamps were not preserved when copying files from ReFS partitions. Fixed the issue that Excel-format reports generated by features such as file copying or bad sector checking could not be opened when the report contained more than one million rows. Fixed the issue that folders were not displayed in the exclude-folder dialog box when backing up partitions to image files. Fixed the issue that the "Erase Sectors" feature could not be executed in some cases. Download: DiskGenius 6.2.0.1829 | 63.9 MB (Freeware, paid upgrade available) Download: DiskGenius Portable 64-bit | 40.0 MB Download: DiskGenius Portable 32-bit | 36.0 MB Download: DiskGenius Lite 64-bit | 13.4 MB Download: DiskGenius Lite 32-bit | 11.6 MB View: DiskGenius Home Page | DiskGenius Screenshot Get alerted to all of our Software updates on Twitter at @NeowinSoftware
    • Really? Use a better search engine https://www.google.com/search?...ourceid=chrome&ie=UTF-8
  • Recent Achievements

    • Week One Done
      agatameier earned a badge
      Week One Done
    • One Month Later
      agatameier earned a badge
      One Month Later
    • Week One Done
      ssd21345 earned a badge
      Week One Done
    • Contributor
      MarkHughes4096 went up a rank
      Contributor
    • Dedicated
      jordanspringer earned a badge
      Dedicated
  • Popular Contributors

    1. 1
      +primortal
      513
    2. 2
      +Edouard
      183
    3. 3
      PsYcHoKiLLa
      143
    4. 4
      ATLien_0
      95
    5. 5
      Steven P.
      75
  • Tell a friend

    Love Neowin? Tell a friend!