Help - Hard Drive Randomly Clicking and Disappearing from Windows Explorer


Recommended Posts

Hi all,

I'm experiencing a strange issue with my PC where one of my 1TB Hard Drives randomly clicks and disappears from Windows Explorer. I can read and write data to it without issues until it disappears from Explorer and the only way to get the Hard Drive to reappear it to reboot the computer.

I am at a loss as to what is causing the issue, but i don't think the hard drive is about to fail as i dont get any issues within Windows when acessing my data. I have used SeaTools to scan the drive for issues and it seems fine.

Could it be a faulty SATA or Power Cable that is casuing the issue?

Well, I can say from experience that if you hear clicking from your hard drive, it's probably on the verge of mechanical failure. As soon as you get access to it, move your files off of it onto another drive. My 2 TB did something similar and at first I could read and write, but after a few weeks, I started having errors on it and the clicking got more frequent. Your best bet is move stuff off of it and then test your theories with different cables and connections on your motherboard. Best bet is to use the same cable on that drive on other drives and the same port on your board to see if that is the problem. But almost always if you hear a drive clicking, it's on the verge of death.

The clicking started a few days ago but it's not constant, it could happen one minute and stop the next, from late last night until the early hours i was streaming movies from it to another computer to watch and it was fine, as i have said its random.

What i have done at the moment is swap the SATA cable with the one from my BluRay Drive and removed a fan molex connecter that i had placed between the PSU and the HDD and all seems fine just now, i will monitor the situation for a few hours to see if this helps.

What everyone else said.

Clicking is the devil's play thing >.>

EDIT::

It's unlikely that the cable is the issue. The most likely outcome if that were the case is the drive just disappears from explorer and gets parked by the drive firmware.

There should be no clicking in this scenario. Clicking = mechanical fault as a rule of thumb.

Nope. Not the SATA Cable. Two thing could happen: the hard drive will die, or you can re-partition it and maybe it will work nicely. I have an old harddrive that clicked and dissapeared many times, I bought a new one then re-partitioned the old harddrive, and the old one works even now. I'm using osx on that old harddrive and it works perfectly, no clicking, not any problems at all.

So try to re-partition it.

Nope. Not the SATA Cable. Two thing could happen: the hard drive will die, or you can re-partition it and maybe it will work nicely. I have an old harddrive that clicked and dissapeared many times, I bought a new one then re-partitioned the old harddrive, and the old one works even now. I'm using osx on that old harddrive and it works perfectly, no clicking, not any problems at all.

So try to re-partition it.

My objection to this is you have no idea which outcome will be the answer.

I take a very black and white approach to this. Once a drive starts clicking, it's out.

You were running a fan off a SATA power cable?

WUT!?

it was set up like this

PSU 4-Pin Molex (female) > Fan 4-Pin Twin Molex (male and female) > Sata 4-Pin Molex (male)

Oh.. Well in that case it's possible there was a power supply issue.

When you say SATA cable, people are always going to think of the data cable.

The clicking could be caused by insufficient voltage reaching components.

Oh.. Well in that case it's possible there was a power supply issue.

When you say SATA cable, people are always going to think of the data cable.

The clicking could be caused by insufficient voltage reaching components.

Yeah thats what i was thinking i removed the fan from between the PSU and HDD and changed the Sata (data) cable.

My objection to this is you have no idea which outcome will be the answer.

I take a very black and white approach to this. Once a drive starts clicking, it's out.

It started to clicking for me... It clicked everyday, the whole pc hanged, I needed to reset, turn off etc... And when I re-partitioned it, it became perfect, and not a single clicking happened from that. This happened 2 years ago, and the hd works perfectly everyday from then. I'm using it right now too. So no, it's not out. Atleast for me.

Baha.. I like that people are all still saying the same thing :p

Clicking = Death. First rule of harddrives :p I'd be backing that drive up regularly I think >.>

let me clarify something the clicking is NOT constant but random and usually stops even if data is being read or written to it. Let me also say that the last time i hear it click was on Monday and it started again about an hour ago.

If it were about to fail the clicking would be constant, i would also experience system freezing, data erros and a whole host of other things.

It started to clicking for me... It clicked everyday, the whole pc hanged, I needed to reset, turn off etc... And when I re-partitioned it, it became perfect, and not a single clicking happened from that. This happened 2 years ago, and the hd works perfectly everyday from then. I'm using it right now too. So no, it's not out. Atleast for me.

Since i have changed the cable there have been no clicks at all, even now that i am transfering around 300GB of data from it. I don't think a randomly clicking drive means its on its way out the door to a tearful goodbye, and i think the issue was the SATA cable, i would love to be proved wrong but i cant see it happening.

are you still under warranty ? i had the same problem you are having & i ended up getting a replacement. from the time i placed the request to the day i got the replaced hd was 4 days

i live in the united states they sent the replacement drive out first & as soon as i got the replacement i sent the failing drive out

it only cost me $10.67

try hirens and use dos tool HDD Regenerator 2011

I will give it a try after my data is backed up

are you still under warranty ? i had the same problem you are having & i ended up getting a replacement. from the time i placed the request to the day i got the replaced hd was 4 days

i live in the united states they sent the replacement drive out first & as soon as i got the replacement i sent the failing drive out

it only cost me $10.67

Yeah i think i am still under warranty, i will try a few suggestions if those fail i will RMA the drive

try hirens and use dos tool HDD Regenerator 2011

All that does is try to recover data from damaged sectors and then marks them as bad. It can be helpful in file recovery but it won't save your drive. Back up everything and pull its life support plug, it's done. Even if it works for a while after running that utility, bad sectors have a tendency to spread. The drive should never be trusted again.

This topic is now closed to further replies.
  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Posts

    • Opinion. All you did was blame Democrats for everything. You offered nothing but a hit piece to support your pro Trump, anti union right wing ideology.
    • Excuse me for having an opinion, fella'... (Why am I not surprised?...) Congrats on your very informative post however...
    • By the sounds of that wall of Fox News propaganda gibberish attacking the Democratic Party you've already had plenty of "juices" flowing this morning. You've ruined what could have been a productive comment thread.
    • (Topic to get the juices flowing this Sunday morning!...) Actually, the situation has almost nothing to do with "lack of skills", especially since assembly-line skills can be taught to anyone, including Americans, certainly. Rather, the inadequacy-to-impossibility of large-scale tech manufacturing in America today, and the reasons why America finds tech manufacturing completely onerous in the 21st century, has to do with politically driven laws amid a plethora of non-scientific, utterly politicized "science-fact" that is patently false, punitive business taxation at every turn, an array of judicial fines of unimaginable scope and complexity, and, last but not least, American unionization strictures that serve to actually slay job creation and hobble all such manufacturing endeavors in America before they can get off the ground. Globalism emerged, they tell us, as the needed answer to American hubris and an unholy American drive to excel. Unless one is buried under mounds of political propaganda, it's easy to see the absurdity of labeling the employees of SpaceX, for instance, as "unskilled labor"... Etc. ad infinitum. At one time in the recent past, American manufacturing prowess was the envy of the world in a wide variety of technical fields! The current federal and state government roadblocks against America becoming competitive globally in tech manufacturing are considerable, it's true, as anyone with a working brain knows. But remarkably, that is only half the story! The other half of the story is, of course, the corporations themselves... Chinese tech manufacturing is simply unassailable in terms of profits, because the Chinese government wants to see its tech manufacturing second-to-none globally so that no companies/nations can compete in terms of ROI, and China has completely succeeded in that goal. Let's tic-off a few things: *Chinese tariff policies are set according to what is considered best for Chinese business, Chinese employees, and the Chinese people. Huge difference with how things are done with tariffs in the US--as the US government (SCOTUS in this case, Congress in others) plainly feels that tariffs are "unfair" for the limited number of citizens who may pay them, whereas nothing is "unfair" when Congress considers the Personal Income Tax rates to be infinitely hike-able, along with infinitely enlarging annual budget deficits. *The Chinese government boldly subsidizes Chinese companies to artificially amplify their profits. *The Chinese government deliberately refuses to avidly demonize Chinese businesses and does not consider Chinese businesses "the enemy", so very unlike American (D)s these days. *Chinese labor laws and businesses are allowed to set their own labor policies according to what Chinese companies consider is best for companies and their employees... Simply put, American workers in tech manufacturing are not allowed to set their own labor policies! * One additional problem corporations have that I also do not sympathize with is they don't want to pay to train their American employees. They could easily do so, but would rather not have to pay for it. I find that pathetic, actually. It is the height of hypocrisy for Americans to decry working conditions in China while simultaneously ensuring that American products are manufactured in China, not in the US, simply to maximize profits. There is nothing wrong with making a profit, of course, absolutely nothing. But there is plenty wrong with attempts to normalize hypocrisy of this kind! But rank hypocrisy and the (D) party in the US are longtime bedfellows... The current government in Washington is working overtime to see if it can toss out the horribly poor, failed economic policies of the past, while the (D)s still in Washington work very hard to bring back the stupidity whenever possible. With the right policies in place, America can be an infinitely competitive manufacturer.
  • Recent Achievements

    • Conversation Starter
      jessse3334 earned a badge
      Conversation Starter
    • Reacting Well
      JuvenileDelinquent earned a badge
      Reacting Well
    • One Month Later
      Excellence2025 earned a badge
      One Month Later
    • Week One Done
      Excellence2025 earned a badge
      Week One Done
    • Week One Done
      flexorcist earned a badge
      Week One Done
  • Popular Contributors

    1. 1
      +primortal
      508
    2. 2
      +Edouard
      198
    3. 3
      PsYcHoKiLLa
      152
    4. 4
      Steven P.
      73
    5. 5
      FloatingFatMan
      62
  • Tell a friend

    Love Neowin? Tell a friend!