Delay in Remote Desktop Connection. What are possible solutions?


Recommended Posts

I am experiencing delays and reconnecting issues when connecting to RDP. Both wired and wireless.

I have purchased a new router - Linksys EA3500 - and still these issues occur.

Ping tests stated around 18ms for my connection.

My internet speeds/subscription are 120 MB down, 10 MB up. I have tested with different "Experience / Performance" settings within RDP, from low-speed broadband to high-speed broadband; all without success.

I have KIS2013 installed with default settings on both computers (wired and wireless).

What can be the issues for these delays/secs of 'hickups' during the RDP-connection?

RDP connections to where? Some box on the internet, or between boxes on your own network - wired to wireless, wireless to wireless, wired to wired?

Also what do you consider delay, 2 seconds, 5 seconds, 10, 20, 3 minutes?

RDP to some box (server) on the internet - our server 80 km away.

The server is wired to its backbone/Internet, I make a RDP-connection via my computer (wired) or notebook (wireless) from home (or elsewhere) - I use its name/alias and not the IP.

The delay is a couple of seconds (mostly 2-5 sec); screen 'freezes', reconnecting popups appears, connection is back again and I can start working again...

And this once every 2-5 minutes.

EDIT:

adjusted delay time to real circumstances

well there could always be a slight delay in resolving to its FQDN, I think that is what you meant by name/alias because those are not resolvable on the internet but a fully qualified domain name is ;) something.something.tld

so you its not really a delay in connection, but a loss of connection and reconnect

"this once every 2-5 minutes."

Are you connecting via a VPN to this server, or just the normal RDP 3389 just over the internet? Is there any firewall on the other end limiting connections to this port to only where your coming from?

You put 3389 open on the public internet and its going to get hit quite often with people attempting to log in.

If your saying it happens every few minutes I would look at logs on server side for any hints, and also would sniff the traffic from your connection. This will show you if your getting a lot of retransmission on lost packets, etc.

lagging could be upstream not fast enough to handle request, could be dns not fast enough to handle name resolution...you mention your upstream, is your upstream the upstream at home or your upstream at the office. The upstream at the office needs to be ~1Mb/s for optimal response...your down stream at home needs to be at least that. Also the dns plays quite a bit into speed, try connecting to the ip to negate dns being an issue. if it is fast connecting to the outside ip, then the issue is dns related.

it's kinda strange... when I use my cell phone with tethering (wayyy slower connection, everything is ok) on the same notebook, I have a good connection and no delay/lag.

It seems that either my modem or router is the "bad kid in town".

I just got a new router today - default settings - so that should not be the issue.

I might just check a direct cable connection from my modem to my computer (thus cancelling out the router) and see what happens...

I'll come back to this latter thing.

@ +Chris13NT, how can I prevent this? Or is this ISP-related?

Just tested it "quick and dirty" and the delay/lag is not present when connecting directly to the modem.

When I put my router in between the lag is there yet again.

There is a power/surge adapter to prevent over-voltage, but this hasn't been an issue ever since.

Might it be cable related? And that one of the UTP-cables has been damaged/is broken?

Replacing might help, but that I need to get myself some new cables....

By the way, the current cable-setup is:

ISP-entrance in my home - cable to modem, provided bij ISP - modem - cable to surge-adapter - cable to router, from there the standard 4 GBit ports of this EA3500 to computer and other periphicals + router wireless to notebook and other periphicals.

What is your dns configuration when connection directly to the modem?

start, run, cmd

ipconfig/all

What is your dns configuration when connected to the router?

start, run, cmp

ipconfig/all

change the dns on your adapter to the dns that you are getting when you are on the modem. does the same problem exist?

dns could be the problem on initial delay, or just failure to resolve - but once the connection is established and having freezes every few minutes does not seem like a dns related problem to me.

What kind of router is it? Some routers have trouble with connections over 50mbit, I had a Linksys E3000 and it couldn't cope with my 85mbit FiOS line, it would crap out every time I pegged the download.

It could be cable related but I doubt it.

I have a brand new Linksys EA3500. It should get "Transfer rates up to 300 + 450 Mbps".

The DNS I get when connect to the router is 1 IP: 192.168.1.1

When directly connected to the modem DNS server is 2 IP's: 213.48. .... and 62.179. ...

yeah those are from your ISP when connected to modem, and when connected to router your using it as your dns forwarder. This is a common setup, your router would then forward dns to those handed to your router via your ISP 213.48 and 62.179

But again if your having the issues once your connected, it seems highly unlikely that it would be dns related.

  On 26/09/2012 at 16:23, BudMan said:

yeah those are from your ISP when connected to modem, and when connected to router your using it as your dns forwarder. This is a common setup, your router would then forward dns to those handed to your router via your ISP 213.48 and 62.179

But again if your having the issues once your connected, it seems highly unlikely that it would be dns related.

Thx. So what can it be?

unlikely sure, test it, verify it, make sure. be sure, not be somewhat sure....perhaps the router is being retarded when forwarding, it is a link in the chain....remove the link.

I thought it was initial connection....if it is not initial connection, then it is not dns related. something is happening with the traffic when it goes from router to modem.

Can you to a trace route to the IP of the RDC server? This might give a clue if you have a hop with unusually high ping.

do tracert <ip (or dns name)> in cmd

The fact that the lag only happens when the router is in the link is making me almost positive it's the router botching things.

  On 26/09/2012 at 16:29, Chris123NT said:

Can you to a trace route to the IP of the RDC server? This might give a clue if you have a hop with unusually high ping.

do tracert <ip (or dns name)> in cmd

In which setup and from where?

From my computer, connected via router, to the RDC server?

Or from the RDC server to my computer? (and also here via router or directly connected to modem?)

  On 26/09/2012 at 17:01, hjf288 said:

Off topic but in reply to Chris, my e2000 handles my 120mbit line with ease and it has a slower CPU than your e3000..

So something is up there..

It could have just been going bad, or it could have been DD-WRT's fault.

  On 26/09/2012 at 16:29, Chris123NT said:

Can you to a trace route to the IP of the RDC server? This might give a clue if you have a hop with unusually high ping.

do tracert <ip (or dns name)> in cmd

The fact that the lag only happens when the router is in the link is making me almost positive it's the router botching things.

What kind of info do you need from this trace?

From which hop# there is a time out? or else?

There has been some less delays (but still annoying) with the new FW... although I had to wrestle myself through the Cisco Cloud Connect.

Still some delays.

Question remains....

EDIT:

I guess I was over-enthusiastic... delays still remain as strong as before :(

This topic is now closed to further replies.
  • Posts

    • Hi all, I've got a Pioneer VSX 815-k receiver. Love this thing, however, my cat did his business on top of it and kinda recked it... Only analog works (5.1 surround RCA inputs). Normally I'd use toslink from mobo to digital in on the receiver, but the result is a ton of loud white noise over the music. Analog works just fine, so I'm forced to use the 3.5mm jacks on the rear of the mobo to the RCA inputs on the receiver. The issue I face is that there is no DTS or anything fun.. Originally, I could play all my MP3s or watch YouTube etc, and the subwoofer would be booming as I like because of the mixing from the DAC. Now with the analog, none of that is happening  I'm wondering if there's some kind of software solution for Windows to get the subwoofer to play as it did when I had it hooked up through toslink, but for analog out instead. As of now, only audio files that were encoded specifically to produce sound to the sub, will work, but nothing else. As to which onboard sound solution my mobo has, this from the website's description: 121dB SNR AMP-UP Audio with ALC1220 & High-End ESS SABRE 9018 DAC with WIMA audio capacitors Sound BlasterX 720°, the top-of-the-line audio engine solution for 4K gaming and entertainment  yea it uses that wonky SBx 720 app to change the audio effects n stuff.. but doesn't help with my issue Eventually yea, I wanna buy a new one. They're about $80 on ebay after shipping, but that will have to wait.
    • Serious question here. Why is the start menu such a heated topic? I can't remember the last time that I used the start menu for anything at all other than it pops up when I hit the WIN key on my keyboard before I type for the program I want to run and then hit Enter or to restart my machine. I honestly wish it would just go away, and it just be replaced with the PowerToys Run menu. Am I missing something with the Start menu? I see people always talking about installing third party replacements and such, but I just wonder what some are actually using the Start menu for that I might be missing out on. Genuine question. Hopefully not offending anyone as I know everyone has their own way to work and access things in the OS.
    • These are the Apple Watch models that support watchOS 26 by Aditya Tiwari Apple has announced the latest operating system upgrade for its smartwatch lineup, called watchOS 26, not watchOS 12, as many expected a while ago. The Cupertino giant has unified the software experience across its platforms by introducing the "Liquid Glass" software design and renaming all the operating systems to version 26. That said, the next question is which Apple Watch models will support watchOS 26. Apple has shared the official list of devices: Apple Watch Ultra 2 Apple Watch Ultra Apple Watch Series 10 Apple Watch Series 9 Apple Watch Series 8 Apple Watch Series 7 Apple Watch Series 6 Apple Watch SE (2nd Generation) The upcoming Apple Watch update brings several new features to your wrist. Liquid Glass design gives a fresh look to the UI with updated Control Center and translucent buttons within apps. It's new Workout Buddy feature can use an Apple Intelligence-enabled iPhone nearby to provide personalized, spoken motivation during workouts. Building on the Double Tap feature, you can now flick your wrist to perform actions like muting incoming calls, silencing timers, and dismissing notifications when your hands are full. It is available on Apple Watch Ultra 2 and Apple Watch Series 9 (or later). watchOS 26 is currently available for testing through the Apple Developer Program. It will roll out to general users during the fall season, when Apple is expected to refresh the Ultra and SE models. Note that your Apple Watch must be paired with an iPhone 11 (or later) or iPhone SE (2nd generation or later) running iOS 26. While the list of Apple Watch models that support watchOS 26 remains the same, it won't work with iPhone Xs/Xs Max and iPhone Xr, which were previously supported on watchOS 11. You can check out the respective lists of supported devices for iOS 26, iPadOS 26, and macOS 26 Tahoe.
  • Recent Achievements

    • Explorer
      MusicLover2112 went up a rank
      Explorer
    • Dedicated
      MadMung0 earned a badge
      Dedicated
    • Rookie
      CHUNWEI went up a rank
      Rookie
    • Enthusiast
      the420kid went up a rank
      Enthusiast
    • Conversation Starter
      NeoToad777 earned a badge
      Conversation Starter
  • Popular Contributors

    1. 1
      +primortal
      501
    2. 2
      ATLien_0
      268
    3. 3
      +FloatingFatMan
      257
    4. 4
      Edouard
      201
    5. 5
      snowy owl
      170
  • Tell a friend

    Love Neowin? Tell a friend!