Fans going crazy, CPU 100% idle


Recommended Posts

I'm going insane over the behavior of my 27-inch, medio 2010 iMac. The CPU fan continues to spin up even though the iMac doesn't do a thing. I've reinstalled OS X Lion multiple times, I reinstalled OS X Mountain Lion several times. I did PRAM-resets more times I can count, same goes for SMC resets. Today I even disconnected the iMac, laid it down on my bed and cleared all the vents with the vacuum cleaner on the weakest setting. The other day a friend of mine walked in and immediately asked why my iMac was making so much noise.

The first picture shows the CPU Fan right after startup. The second less than two hours later. I haven't done a thing with the iMac except play music and browse the web a bit.

How on Earth is it possible the fans spin up, sometimes over 4000 rpm, when the CPU sits next to idle most of the time? The worst part is they won't power down once the iMac cooled off. There are no optical drives in the SuperDrive either.

The measurements are in Celsius. The room temperature averaging at 20,5 degrees throughout my apartment. It's only 14 degrees here in Amsterdam.

post-128385-0-15321200-1348764232_thumb.

post-128385-0-38335300-1348764664_thumb.

post-128385-0-02210400-1348765019.png

Link to comment
https://www.neowin.net/forum/topic/1108523-fans-going-crazy-cpu-100-idle/
Share on other sites

assuming your temps are in Celsius it is spinning up because the chip is hot. Is there anything to justify the chip being hot? Dust on the HSF, high ambient temp, etc?

I can't really say for sure how much dust has accumulated inside the iMac itself, but judging by how little there was directly underneath the grill I seriously doubt it's a lot. I tried looking inside with a flashlight but everything seemed clear.

If I leave my iMac on for long periods of time the fans will gradually get faster and faster until they are 100% on, and they will not go back to normal speeds unless I shut down and power back on. Rebooting just keeps them running at full tilt.

It's strange. It's like the driver/sensor controlling it has failed to do it's job properly. :/

Yeah if it's THAT hot at idle, you have a problem on your hands.... either your system has absolutely 0 airflow or the heatsink aint applied correctly, if so I'd take the computer and bring it to a store.

Did you recently install an SSD?

http://forums.macrum...d.php?t=1235234

That actually affects the hard drive fan, not the CPU fan (at least it did in my Late 2010 iMac). Also, it happens a lot sooner than 2 hours after boot. :p

Maybe your GPU is being taxed by something? The CPU fan cools both, so...

Yeah if it's THAT hot at idle, you have a problem on your hands.... either your system has absolutely 0 airflow or the heatsink aint applied correctly, if so I'd take the computer and bring it to a store.

It's an iMac. It's normal for things to run a little bit hotter.

Did you recently install an SSD?

Everything is stock. No modifications whatsoever have been made to the iMac after I unpacked it. Also, the SSD issue wouldn't affect the CPU fan, rather the HDD fan.

Maybe your GPU is being taxed by something? The CPU fan cools both, so...

Okay, this is something I can work with. Is there any way of checking what the GPU load is?

If I leave my iMac on for long periods of time the fans will gradually get faster and faster until they are 100% on, and they will not go back to normal speeds unless I shut down and power back on. Rebooting just keeps them running at full tilt.

It's strange. It's like the driver/sensor controlling it has failed to do it's job properly. :/

That's EXACTLY what ****es me off. The fans won't slow down once things are cooling off.

UPDATE:

Okay this is incredibly interesting. I'm now 100% sure this is indeed a software issue, rather than a hardware related one. For whatever reason OS X Mountain Lion is telling my iMac to increase CPU fan speed in order to cool off. But apparently this is a one-way street. As time progresses the fan speed just continues to go up until it hits a maximum of about 4150 rpm. Like jamesyfx noticed they it will continue running at its maximum until I do a full shutdown. So for whatever reason OS X Mountain Lion won't tell my iMac to reduce fan speeds once it cooled off.

After a lot of Googling I noticed other people having the same issue with OS X Mountain Lion. Not just iMacs but MacBook Pros too. One person came with the suggestion to temporarily download and install iStat Menus 2, set Fan speed control to "Medium" (it's on of the default "rules") and then return to "Default". In literally an instant my iMac's CPU fan would drop from its maximum of ?4150 to a quiet 1940 and then continued to drop.

Check out the below screen shot and note the uptime: Over 6 hours and a regular CPU fan speed of 1885 (it's still dropping as I type).

So what's going on here people?

post-128385-0-90926700-1348790216_thumb.

It does a similar thing on my system, CPU fan speed drops down to a steady 1190rpm when I set to default.

Seems like it kicks the default behaviour back in once you set it as such.

My iMac is a completely different model to yours, so the issue must be software related.. and I think using this utility has proven that.

Yeah that's exactly what seems to happen. iStat basically slaps OS X on the wrist telling it do proper fan control. After a while CPU fans would indeed drop to an average of 1190 rpm on my model as well. Here I was thinking my CPU/GPU fan was constantly triggered because it couldn't handle the new OS X Lion/Mountain Lion graphics effects. But that's not it either.

Anyway, it seems like you can uninstall iStats Menu from your system until you do a SMC reset.

I'm not familiar with Mac since i never owned one but why does OSX has to control the fan ?

I would never ever trust any OS to control the fan speed of my computer. Right now i have a fan controller but if i would not have one i would let my Motherboard control the fan speed or at worst install my MB software (or a 3rd party alternative like speedfan) to control them.

Here's an interesting blog post about the issue. You probably have already read it since it was in the first 10 results of a google search but i still post it just in case.

http://gigaom.com/ap...lion-heres-why/

Spotlight reindexing doesn't take days or weeks.

  • 2 weeks later...

Maybe this helps:

http://www.hddfancontrol.com/

OR:

Symptoms

After plugging in the iMac and turning it on, the fans (blowers) may be noisy and appear to run at full speed. In this event, shutting the iMac off and turning it on again wouldn't fix the issue.

Resolution

If you press the iMac power button while you are inserting the power cord, the iMac will enter a mode in which the fans (blowers) run at full speed. In order to correct the issue, reset the SMC and then start the computer by pressing the power button after the power cord has been fully inserted.

The iMac should now start up and operate as expected.

http://support.apple.com/kb/TS1433

AND:

First download and install smcFanControl 2.2.2. Set it up to provide (still quiet) minimum fan speeds of 2200 rpm for the HD and 2800 rpm for the CPU, leave the Optical Drive fan at 600 rpm to minimize dust accumulation (or just tweak it up if/when you will be using it much) ....

http://hints.macworl...110606033134359

UPDATE:

Okay this is incredibly interesting. I'm now 100% sure this is indeed a software issue, rather than a hardware related one. For whatever reason OS X Mountain Lion is telling my iMac to increase CPU fan speed in order to cool off. But apparently this is a one-way street. As time progresses the fan speed just continues to go up until it hits a maximum of about 4150 rpm. Like jamesyfx noticed they it will continue running at its maximum until I do a full shutdown. So for whatever reason OS X Mountain Lion won't tell my iMac to reduce fan speeds once it cooled off.

After a lot of Googling I noticed other people having the same issue with OS X Mountain Lion. Not just iMacs but MacBook Pros too. One person came with the suggestion to temporarily download and install iStat Menus 2, set Fan speed control to "Medium" (it's on of the default "rules") and then return to "Default". In literally an instant my iMac's CPU fan would drop from its maximum of ?4150 to a quiet 1940 and then continued to drop.

Check out the below screen shot and note the uptime: Over 6 hours and a regular CPU fan speed of 1885 (it's still dropping as I type).

So what's going on here people?

I'm confused. Did that software package end up solving the problem for you or is it still an issue?

Off hand I would say the temp gauges are wrong, without touching the cpu or the motherboard touch the bottom of the heat sink(while the computer is on) and see if its hot. That feels like the CPU is over heating(which would cause the 100% cpu usage).

I have no idea what you're talking about or why you think there is 100% CPU usage. :/

  • 2 weeks later...
  • 2 years later...

Hi there, old thread, but hopefully someone is still around.

I have an iMac 27 late-2009, 3.06 Ghz, 8gb RAM, running OS 10.8.5, and all the hardware is original (no HD swap...). So, it has a similar problem: it takes about an hour for the CPU fan to gradually speed up from the initial approx 1200 RPM to around 4000 RPM. Then, all I have to do is to put it to sleep for enough time to let the fans stop spinning (that's not even 5 seconds) and then wake it up to see the CPU fan at normal speeds. And here it goes for another hour of gradual increase... See the screenshot of the iStats Menu, the graph shows the increase in the last hour, and the three previous increase/sleep patterns... The other two fans are just fine. All of that time, the iMac is at idle, nothing running at all. My iMac isn't my main computer, so i kinda left the problem as it was, spending an hour or so every couple of months trying to solve the issue, but after these 5 years of fruitless efforts, I can't believe I haven't solve it yet! Even though I get answers a lot from forums, here's my first post in one of them (ever!), in hope it will help.

 

Here are the solutions I tried already: smcFanControl, HDD Fan Control, iStats Fan Rules... Nothing seems to be able to override the fan speeds, nothing at all! I vacuumed the air input and output... And of course, I did the SMC reset. I try to remember all the other things I tried to do, but it gets confusing after those years of diverse problem solving. I did many upgrades (and even downgrades) too but I doubt it has anything to do.

 

Even though I never opened the iMac's case (I DID open the bottom latch to replace RAM memory at some point, comes to my mind... but that's not the back case) I wonder if it has anything to do with some hardware that would just be misplaced at the factory of because of a shock while moving the computer around... 

 

Anyone has any idea? Anything I could try?

 

Screenshot:

https://www.dropbox.com/s/vfvkr1zordrbznb/Screen%20Shot%202015-01-14%20at%2011.59.57%20PM.png?dl=0

This topic is now closed to further replies.
  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Posts

    • Microsoft confirms Windows 11 26H2, urges IT admins to prepare for release by Usama Jawad Windows 11 typically follows an annual update cycle, but Microsoft recently broke that tradition a bit by releasing a "26H1" version in the first half of this year as a "scoped" build for select new silicon PCs only. This version was not available for customers using 24H2 and 25H2 builds, as Microsoft is busy preparing version 26H2 for them, confirmed officially for the first time. In a Windows IT Pro blog, Microsoft has urged IT admins to prepare for the upcoming release of Windows 11 version 26H2. The company has confirmed that this will be a small enablement package (eKB) that will simply light up certain disabled features that are already present in the operating system's code base. This means that the "refined" Windows update and deployment experience will be simpler and quicker, with minimal disruptions, as the feature update will simply toggle a few flags rather than performing a complete replacement. Microsoft has explained that this is all possible because the standard Windows 11 releases share the same servicing branch and hence, the same source code. However, this also means that Windows 11 26H1 users won't be able to upgrade to 26H2 as that is a different branch, but this is something we have known for a while now. Similar to previous annual feature updates, Windows 11 26H2 will offer the following support cycles: 24 months of support for Home, Pro, Pro EDU, and Pro for Workstations editions 36 months of support for Enterprise, Education, IoT Enterprise, and Enterprise Multi-session editions Microsoft has not confirmed a concrete release date for Windows 11 26H2, but noted that it is "coming soon". If we go by the ongoing release cadence, we can expect it to begin rolling out in early October 2026. As such, IT admins have been encouraged to begin validating Windows Insider releases in the Experimental Channel, plan rollout rings, and strategize the utilization of their existing deployment tools.
    • Windows 11 gets new audio improvements in the latest builds by Taras Buria Today's Experimental builds (26H1 and Future Platforms, formerly Canary) pack several audio-related improvements. If your device is enrolled in the Experimental Channel (26H1), you can download build 28120.2315, while those in the Future Platforms version have build 29613.1000 to try. Here is what is new in build 29613.1000: [Audio] Following up on our previous improvements, we’re making some more adjustments to Settings > System > Sounds based on your feedback. Namely, we’ve updated the “All sound devices” page so: You now have the ability to change default devices from this page. Each of the devices displayed on this page now has a little volume meter next to it to show if there is audio actively playing. We’ve adjusted the page design slightly so now you can filter whether you’re viewing input or output devices. We’ve added toggles so you can choose if you want to hide or show disabled, disconnected, and unplugged devices on this page. We’ve also updated the input and output audio properties page for devices in Settings to now include jack information for those that need it. And here is the changelog for build 28120.2315: This update includes a small number of minor bug fixes and improvements. [Accessibility] This update improves caption style responsiveness by redrawing captions immediately for caption style changes. If no current caption is visible, a sample caption string is displayed. [Audio] This update improves the reliability of the inbox HD Audio driver. You can find the official release notes for build 28120.2315 here and for build 29613.1000 here.
    • I agree with what I think you are saying, just not in the way you are saying it. Like any tool, the amount it represents your work is perorational to the effort you put into it. It is similar to why 2nd grade math students learning to add and subtract are not allowed to use calculators, but a high-school calculous student is. For the 2nd grader, that tool would completely replace the work they are doing, for the calculous student the same tool allows them to work far more effectively while in no way replacing their effort or knowable. If you spend 30 seconds writing a prompt, then the image that comes out is no more "yours" than if you found the same image with a Google Image search. However, many of these generative tools also support highly iterative processes that allow back and forth, and merging generated images with photos or human created images. I am sure you would agree that a human spending hours of time working on a project, even if AI was involved in the process, still reflects that human's work.
    • Windows 11 version 26H2 is now available for testing in the latest preview build by Taras Buria Friday Windows 11 preview builds are here. Insiders in the Experimental (formerly Dev) and Beta Channel can download builds 26300.8697 and 26220.8690. There are no new features, but Microsoft is officially moving the Experimental Channel to version 26H2. In addition, Microsoft is improving the copy dialog in File Explorer, the Start menu reliability, and fixing virtualization issues. Here is the changelog: [General] With today’s build, Windows Insiders in the Experimental channel will see the versioning updated under Settings > System > About (and winver) to version 26H2. For more information, see the Windows Insiders blog. [File Explorer] We’ve improved the visual consistency and reliability of the Copy dialog in Dark mode, including its launch experience and the expanded progress view. [Start menu] - Also available in Beta Improved reliability of Start menu reflecting newly installed or removed apps without requiring sign-out or restart. [Taskbar] Fixed an issue for Insiders using the new smaller taskbar option, where the system tray might get cut off or pushed off screen. [Settings] - Also available in Beta Improved reliability of Settings > Apps > Startup. [Virtualization] - Also available in Beta This update addresses an issue that could result in bugchecks citing HYPERVISOR_ERROR (0x20001) and KMODE_EXCEPTION_NOT_HANDLED (0x1E) errors after installing the latest flights on some devices during system restarts, virtual machine operations, or while running some gaming applications. You can find the official changelog for the Experimental build here and for the Beta build here.
    • I've always preferred this possibility. There is something that feels good about the idea that all matter in the universe will eventually come back together and maybe even result in another big bang. The idea that the universe would fizzle out over the eons and forever drift apart is a little depressing. I realize it is not logical to let a basic human desire for life to have a grand everlasting meaning change the way I feel about a scientific theory, but I am human, so that is how I feel :-).
  • Recent Achievements

    • Collaborator
      ryansurfer98 went up a rank
      Collaborator
    • Week One Done
      Eurosoft10 earned a badge
      Week One Done
    • One Month Later
      Eurosoft10 earned a badge
      One Month Later
    • One Year In
      Skeet Campbell earned a badge
      One Year In
    • One Month Later
      Sharbel earned a badge
      One Month Later
  • Popular Contributors

    1. 1
      +primortal
      574
    2. 2
      +Edouard
      188
    3. 3
      Michael Scrip
      77
    4. 4
      PsYcHoKiLLa
      76
    5. 5
      neufuse
      71
  • Tell a friend

    Love Neowin? Tell a friend!