Intel Core 2 E8400 too hot?


Recommended Posts

Hello,

Since I cleared my computer of dust earlier, I've been looking at the CPU temp and it's currently running at 90+C on both cores...one is at 95C.

It keeps going back down after a while. CPU is under high load as I've got a few tabs open in Chrome and I'm installing updates from Windows Update.

Never noticed what it ran at before, but can anyone say if this is too high? The temps are coming from an app called "Speccy."

Cheers

Link to comment
https://www.neowin.net/forum/topic/1123544-intel-core-2-e8400-too-hot/
Share on other sites

Yeah, thats too hot. If you're using the stock Intel heatsink it should be around 40c - 55c - idle, and around 65c under load.

Is it the stock Intel heatsink you're using? If so check to make sure the plastic retention clips are all pressed in to secure the heatsink to the cpu.

Yeah, thats too hot. If you're using the stock Intel heatsink it should be around 40c - 55c - idle, and around 65c under load.

Is it the stock Intel heatsink you're using? If so check to make sure the plastic retention clips are all pressed in to secure the heatsink to the cpu.

Not really sure what I'm looking for, I don't know much about PC internals. I'll do some googling then see if I can figure it out :p

Cheers

What kind of cleaning? Is it possible you disconnected the CPU fan?

Also, did you check the temps before cleaning the PC? It's possible that program is giving you bad information.

FYI, 90? is near the point where that CPU will shut itself down, so if it's really getting that hot, don't keep using it.

What kind of cleaning? Is it possible you disconnected the CPU fan?

Also, did you check the temps before cleaning the PC? It's possible that program is giving you bad information.

FYI, 90? is near the point where that CPU will shut itself down, so if it's really getting that hot, don't keep using it.

Sprayed it with compressed air. I disconnected a fan on the side of the case but connected it again when I was done.

How many fans should typically be running? I downloaded "SpeedFan" and it says this:

Sys Fan: 0 RPM

CPU0 Fan: 902 RPM

Aux0 Fan: 0 RPM

CPU1 Fan: 0 RPM

Aux1 Fan: 0 RPM

:s

I stupidly didn't check the temps before I cleaned it.

What does SpeedFan tell you your temps are?

SpeedFan will report the RPMs of any fans connected to the motherboard fan headers. If they're just wired to the CPU, they won't show up. That said, if it's really 90?C, the CPU fan should be going much faster, somewhere in the 3000 - 4000 RPM range.

I got an E6750, OC'd to 3,00Ghz and temps are 35-65C (it was OC'd to 3,2 before, and temps was same), and I'm using the stock Intel cooler. So 90C is HOT.

Btw, my Intel stock cooler runs on 1300-2200RPM (~1350 rpm on idle).

What does SpeedFan tell you your temps are?

SpeedFan will report the RPMs of any fans connected to the motherboard fan headers. If they're just wired to the CPU, they won't show up. That said, if it's really 90?C, the CPU fan should be going much faster, somewhere in the 3000 - 4000 RPM range.

Currently says CPU 63C / Core 0 70C / Core 1 69C. PC is under less load now though.

All three of those temps have a flame icon next to them, which I'm guessing is bad :p

Could be that the fan won't spin fast enough maybe?

Currently says CPU 63C / Core 0 70C / Core 1 69C. PC is under less load now though.

All three of those temps have a flame icon next to them, which I'm guessing is bad :p

Could be that the fan won't spin fast enough maybe?

Is it spinning at all? :)

I would expect the temps to be lower at idle even if just connected to the heatsink, without a fan, assuming your room isn't somewhere in the desert.

First off, never mind what people are saying and do one thing FIRST !

double check wether your reading the temp as FARENHEIT or CELCIUS !

If its is Farenheit then don't worry about it and carry on about your business / everything is fine !

If it is Celcius your reading ? ..then start worrying !

Your CPU will shut itself off at about 100 degrees Celcius so it is not possible to damage the cpu that way

but if you were to run it close to the limit all the time it would suffer damage i'm sure (shorter life span)

grab something like CoreTemp or RealTemp and see what it sets for your TJ max

ansd see what your getting reported for TCase and your 2 T Junction sensors.

My similar C2D runs some what idle at about 38 c (Tcase) and 38/36 for the two Tjunction's

and that is about 105/100/97 in farenheit.

So to put that into persepctive for you.. i have done TONS of case mods and used many fans etc

And my temps under NO circumstances will read lower that ! approx 36/38 is teh lowest possible temp.

And one last piece of trivia for you too

The internal Core temps (TJ1 and TJ2) are designed on purpose to have a sliding slope on teh accuracy..

the higher the temp the more accurate the temp is. So what the lowest temp is would be the least accurate.

ANd that doesn't matter who or what reads it either.. it is how the chips are manufactured and calibrated at the factory.

edit:

sorry about the poor spelling. i can't type anymore lol

and i'd fix it but my damn browser seems stuck showing the edit window with a black background

on dark grey lettering with font sizes i think 2 or 3 (on my 1080p desktop screen rez)

..gonna need bonoculars if they make screens any bigger lol

Is it spinning at all? :)

I would expect the temps to be lower at idle even if just connected to the heatsink, without a fan, assuming your room isn't somewhere in the desert.

Yeah the damn thing makes a right racket, that's why I cleaned it out to begin with, because I thought it was the dust making it noisy.

I live in rainy England, no danger of overheating from the weather :p

Hyper 212 EVO is only 25 bucks.... get it if you want a cheap air cooler.

under stress the CPU or GPU shouldn't get any higher then 70C... even under full load...

mine at semi-idle with lots of browser activity:

Intel Core i5 3570K @ 3.40GHz 34 ?C

Ivy Bridge 22nm Technology

on Skyrim mine both never exceed 55C even on max settings... the 3D mark software didn't even push it past 60C

First off, never mind what people are saying and do one thing FIRST !

double check wether your reading the temp as FARENHEIT or CELCIUS !

I'd be impressed if he's managed to cool an Intel Core Duo to below room temperature on a shoddy fan. :laugh:

If you're at 60-odd at idle, or near it, I'd guess your heatsink is either unseated or the thermal paste has worn off.

you'd be surprised what you can do on air with a well designed air flow system..

most people i see on the net BUY crap and brag period.

few actually put any thought into airflow and fewer yet do any case modding.

I know myself i have used the same deluxe case i got in '04 ish

and i have refined teh airflow in continually and i find it hard to believe

many other people would have put their system under such a large variety of tests

and the volume of them too. I have used almost evey testing method and material i want

to test and mod my airflow / efficiency.

I have got it to where if you put anything near the openeing it would suck it in with extreme force. lol

I have found the most usefull thing in case modding to be a length of thread from my sewing kit (for obvious reasons ?)

This rambble is in response to people talking about air cooling a cpu.. let me put it this way

i've never seen any bragging hot shots do better with their water pumps than i can do case modding on air.

Kids + money + bragging don't make you any good at anything.

Person xyz buys random crap from egg and adds them to his/her Rig specs and some how that equals

uber leet "dah bomb" case. It gets old watching kids brag by model number about what case they have

when they *should be able to take ANY case on earth and make it awesome. aka. a REAL computer nerd

will be acase modder and not a case BUYER lol

8 years ago the novelty of all my case LED's wore off and teh black ligh made for pc cases i bought at the same time

hasn't been on since either.. i've even gone to the trouble of disabling my power button so i don't have to see

the blue led power button on at night or my front case led lights strips.. all that crap is disabled.

But if i wanted more i would pull out my collection of mini controller and led multi colored lights collection and my soldering iron

and maybe even the Dremel ;) ..but all that is crap if your machine is on fire lol

For a lot a years now the only thing of value to me is the temperatures of my hardware components

and what i can do to lower them even more.. you'd be surprised what persistence and experimentation can come up with.

even on air !

This guy never did respond back what the problem was afterwards so maybe he was reading Farenheit ? then there was no problem..

Temperatures on my PC I would say is a passion but that would be a lie.. I would have to call it an obsession lol

ANd I tell ya people bashing stock C2D coolers are fools. If i can bottom out the sensor reading on three different stock style coolers

on air then they arn't that bad..In other words i mean bottom out as in i can not get the sensor to read lower it will NOT go lower !

and THAT is for damn sure cold *enough and definatly not worth of bashing so called crappy air cooled cpu fans !

Like most things in life its what you make of it.

Also I'd be more worried about Noobs putting too much paste on a cpu then "it wearing off"

The manufacturers instructions are usually too much. and i use probably even less cause i lapped my C2D ;

Rethink the concept as to why it is supose to be there in teh first place.. its not there to be a 2 mm padding of goop

block the two parts.. its supose to be there to complement the parts and aid them in joining together as one piece.

to work unified. (fill in the cracks etc on a sub micro level)

I have done many tests in the past proving less is better than more.. trying experimenting and logging temps and you'll see..

too much of it is a BAD thing and I think most people add to much. I've pulled off probably close to a thousand cpu's off mobo's

in teh last decade and people plaster that crap on like insane lunatics.

While that rant was all well and good, most people don't put thermal paste on their stock heatsinks (there's no indication here that he built this, and he mentioned not even knowing where the heatsink was...), so there's a better chance it wore off.

Also, no Core 2 would sensor would read accurately (if at all) if the CPU was running at room temperature (~20? C).

you'd be surprised what you can do on air with a well designed air flow system..

most people i see on the net BUY crap and brag period.

few actually put any thought into airflow and fewer yet do any case modding.

I know myself i have used the same deluxe case i got in '04 ish

and i have refined teh airflow in continually and i find it hard to believe

many other people would have put their system under such a large variety of tests

and the volume of them too. I have used almost evey testing method and material i want

to test and mod my airflow / efficiency.

I have got it to where if you put anything near the openeing it would suck it in with extreme force. lol

I have found the most usefull thing in case modding to be a length of thread from my sewing kit (for obvious reasons ?)

This rambble is in response to people talking about air cooling a cpu.. let me put it this way

i've never seen any bragging hot shots do better with their water pumps than i can do case modding on air.

Kids + money + bragging don't make you any good at anything.

Person xyz buys random crap from egg and adds them to his/her Rig specs and some how that equals

uber leet "dah bomb" case. It gets old watching kids brag by model number about what case they have

when they *should be able to take ANY case on earth and make it awesome. aka. a REAL computer nerd

will be acase modder and not a case BUYER lol

8 years ago the novelty of all my case LED's wore off and teh black ligh made for pc cases i bought at the same time

hasn't been on since either.. i've even gone to the trouble of disabling my power button so i don't have to see

the blue led power button on at night or my front case led lights strips.. all that crap is disabled.

But if i wanted more i would pull out my collection of mini controller and led multi colored lights collection and my soldering iron

and maybe even the Dremel ;) ..but all that is crap if your machine is on fire lol

For a lot a years now the only thing of value to me is the temperatures of my hardware components

and what i can do to lower them even more.. you'd be surprised what persistence and experimentation can come up with.

even on air !

This guy never did respond back what the problem was afterwards so maybe he was reading Farenheit ? then there was no problem..

Temperatures on my PC I would say is a passion but that would be a lie.. I would have to call it an obsession lol

ANd I tell ya people bashing stock C2D coolers are fools. If i can bottom out the sensor reading on three different stock style coolers

on air then they arn't that bad..In other words i mean bottom out as in i can not get the sensor to read lower it will NOT go lower !

and THAT is for damn sure cold *enough and definatly not worth of bashing so called crappy air cooled cpu fans !

Like most things in life its what you make of it.

Also I'd be more worried about Noobs putting too much paste on a cpu then "it wearing off"

The manufacturers instructions are usually too much. and i use probably even less cause i lapped my C2D ;

Rethink the concept as to why it is supose to be there in teh first place.. its not there to be a 2 mm padding of goop

block the two parts.. its supose to be there to complement the parts and aid them in joining together as one piece.

to work unified. (fill in the cracks etc on a sub micro level)

I have done many tests in the past proving less is better than more.. trying experimenting and logging temps and you'll see..

too much of it is a BAD thing and I think most people add to much. I've pulled off probably close to a thousand cpu's off mobo's

in teh last decade and people plaster that crap on like insane lunatics.

Sorry I must've missed your earlier post, but I indicated the temperatures were Celsius in the original post :p They're definitely Celsius, not Fahrenheit.

While that rant was all well and good, most people don't put thermal paste on their stock heatsinks (there's no indication here that he built this, and he mentioned not even knowing where the heatsink was...), so there's a better chance it wore off.

Also, no Core 2 would sensor would read accurately (if at all) if the CPU was running at room temperature (~20? C).

Yeah I bought the PC off eBay about five years ago. I know what most PC parts do and often thought about building my own, but I haven't really messed about with hardware much yet.

If I get an anti-static wristband, should I buy a mat as well? Some people say you just need to attach a wristband to a non-painted part of the PC case, but others say you need to get a mat as well!

Thanks

Yeah I bought the PC off eBay about five years ago. I know what most PC parts do and often thought about building my own, but I haven't really messed about with hardware much yet.

If I get an anti-static wristband, should I buy a mat as well? Some people say you just need to attach a wristband to a non-painted part of the PC case, but others say you need to get a mat as well!

Thanks

I've never used one myself, and I've built a few PCs. Heck, the last one I built, I turned away for a second and my cat jumped in the case and sat down on the motherboard. :laugh:

That said, static electricity = bad, but a wristband should be good enough.

I've never used one myself, and I've built a few PCs. Heck, the last one I built, I turned away for a second and my cat jumped in the case and sat down on the motherboard. :laugh:

That said, static electricity = bad, but a wristband should be good enough.

I got impatient and just touched a tap/radiator before touching anything :p

Removed the heatsink, cleaned all the dust off it (didn't think to check there when I cleaned it before) and put it back. Made no difference to the temps but the PC seems quieter.

You think I might need a new heatsink?

Thanks for all the help :)

Was there any thermal paste on the heatsink?

Ideally if you pull it off you clean the heatsink and CPU with rubbing alcohol, reapply a thin layer of thermal paste, then reinstall. If you're going to do all that, I'd suggest getting a better one while you're there, like the Cooler Master 212 or a similar large fin push/pull design. They can be found relatively cheap (~$25, plus a few dollars for paste), plus you can reuse them since they fit almost every CPU design out there.

Was there any thermal paste on the heatsink?

Ideally if you pull it off you clean the heatsink and CPU with rubbing alcohol, reapply a thin layer of thermal paste, then reinstall. If you're going to do all that, I'd suggest getting a better one while you're there, like the Cooler Master 212 or a similar large fin push/pull design. They can be found relatively cheap (~$25, plus a few dollars for paste), plus you can reuse them since they fit almost every CPU design out there.

There was some on it but it looked spotty, like it was missing from parts.

I'm not too bothered about this PC, it's quite old now and I have an iPhone and iPad that I can use if it dies, mainly wanted to stop the noise and it seems to have done so for now!

I'll probably replace the whole thing soon :p

Thanks

Hyper 212 EVO is only 25 bucks.... get it if you want a cheap air cooler.

under stress the CPU or GPU shouldn't get any higher then 70C... even under full load...

mine at semi-idle with lots of browser activity:

Intel Core i5 3570K @ 3.40GHz 34 ?C

Ivy Bridge 22nm Technology

on Skyrim mine both never exceed 55C even on max settings... the 3D mark software didn't even push it past 60C

Got the 212 too, it's a big heatsink but it does the job.

This topic is now closed to further replies.
  • Posts

    • Trailer park trash “sport “, fits the current White House
    • KataLib 5.3.0.0 by Razvan Serea KataLib is more than just a music player — it's a complete audio suite designed for music lovers and creators alike. It combines a powerful audio player, a flexible metadata editor, a capable audio converter, and a music library manager into one streamlined application. Core Features: Audio Player Enjoy seamless playback of virtually any audio format or even streaming video files. DJ Mode lets you mix tracks with manual or automatic crossfades. You can also load and save WinAmp-style playlists for quick access to your favorite sets. Audio Converter Convert between a wide range of audio formats effortlessly. Trim or normalize your output automatically, and even extract audio from streaming video sources. Ideal for preparing files for different devices or platforms. Metadata Editor View and edit ID3v2 tags and other metadata. Batch edit multiple files at once, and fetch missing information directly from the MusicBrainz database. You can also apply or update album art with ease. Music Library Manager Organize your entire audio collection, search across tracks instantly, and download cover images from the internet — or use your own custom artwork. KataLib makes it easy to keep your library tidy and enriched with useful info. Supported Formats: KataLib supports a wide range of both lossy and lossless audio formats: Input: OPUS, AAC, FLAC, M4A, MP3, MP4, MPC, APE, AIF, MKV, AVI, MOV, FLV, WEBM, Ogg Vorbis, WAV, WAVPack, WMA, AC3, OGA, MP2, MPGA, MPEG, DTS, M4B, DSD (DFS) Output: OPUS, FLAC, M4A, MP3, Ogg Vorbis, WAV Under the hood, KataLib uses the trusted FFmpeg engine for audio conversion and media playback, ensuring compatibility with virtually all mainstream media formats. KataLib 5.3.0.0 changelog: Added Option to select the Zoom level of the Oscilloscope visualizer. The taskbar button of the app now displays the progress of its processing tasks. The metadata text of the Visualization Video can now be aligned by the user. We can now reorder the order of the Visualizers and Metadata, in the Visualization Video Setup dialog, by removing any item and adding it again. It will be added at the end. Changed The font size of the Visualization Video can now be more than 30 points. Updated yt-dlp library to version 2026... Fixed Opening the Visualization Video Setup dialog could fail if the settings were wrong. Sometimes there were false duplicates in the Rename Tracks dialog. Tracks without metadata appeared without title in the Recent menu. Download: KataLib 5.3.0.0 | 90.0 MB (Open Source) Links: KataLib Home Page | Github | Screenshot Get alerted to all of our Software updates on Twitter at @NeowinSoftware
    • EA Sports UFC 6 review: Brutal, satisfying, and surprisingly accessible to newcomers by Pulasthi Ariyasinghe EA’s UFC series of fighting games has been putting out games for over 10 years now, but it’s a series I have never spent any time with. As a PC guy, the series being console-exclusive is the primary reason for that. The latest entry to the series, EA Sports UFC 6, is still not coming to PC, but I have an Xbox now. When EA reached out to see if I could have a crack at the game and give my opinion about it, I finally got the chance to see what this franchise is about. I have spent about a week playing UFC 6 on the Xbox Series X. Despite my lackluster skill with fighting games, I still have fun with entries like Street Fighter and Tekken. I quickly came to realize this is a different kind of fighting game, not the arcade titles I am usually dabbling with. Most of the week that I spent playing UFC 6 was in the career mode, trying not to get knocked out while slowly improving my combos and reactions. The review below will be from the perspective of a newcomer to the series and an amateur fighting game fan, so please forgive any mistyped lingo or series-staple mechanics I am not comprehending. In the Ring Getting a solid hit in UFC 6 is satisfying. It’s probably the most satisfying impact reaction I have seen in a fighting game. The ripples in the muscles, the spray of sweat (and blood), the meaty sound, and the subsequent stumble all carry a lot of weight. If I miss a heavy swing like that, though, I already know that I'm in for a world of hurt from the incoming counters. The fighting is a real treat. The actions aren’t as snappy as arcade titles, so a miss feels like a much bigger mistake here. This slowness did take some getting used to, but I felt the improvement in my abilities even after a few drills with basic punch and kick combos. If I’m not deliberate with my actions in the ring, whether it be a hasty retreat or a flying punch, the possibility of getting instantly knocked out is always there. The head, chest, and legs all come with their own health bars, so guarding just one area is just asking for trouble. A few hits to the head, and it's game over. Meanwhile, you won’t even be able to stay on your feet if they get damaged enough, drastically lowering the total amount of stamina available for the rest of the match. I was also encountering a large range of fighting styles to customize my own fighter with. There are a huge number of real-life superstars here from multiple eras. It’s not as exaggerated as Street Fighter or Tekken, but the way they move, evade, throw punches, or even take steps is based on their real-life counterparts. I can see this being a big draw for any mixed martial arts fan. One feature I was surprised to see here was the 'Flow State' ability. As rounds progress, a power-up meter can give a temporary boost to the unique fighting style of the selected fighter, essentially boosting what they are good at. There is an entire visual effect that kicks in when activating this, too. The surprising part was seeing something like this in a game that feels like it’s aiming to be more of a simulator than an arcade fighter. My skill level is too low to use this exactly how the game wants me to, so I ended up triggering it whenever the opponent did it as well. Streamlined vs Authentic When I first started it up, UFC 6 asked me about my experience with the series. Being genuinely new, I took its advice and opted for a lowered difficulty level and 'Streamlined' controls. Quickly, I realized that this wasn’t for me. My chosen fighters were throwing random attacks, no matter what combination the game was trying to teach me. Win streaks were happening, and I was already getting bored out of my mind just a few matches in. Turning off this mode and switching to 'Authentic' controls fixed everything right up. I was now able to control my fighter with more precision than I expected. I could control each arm and leg, which body part my attacks would aim at, and the fully customizable controls for setting up unorthodox moves were a cherry on top. None of these made me an expert at the game, but at least I was being beaten up fairly. This is not a point against UFC 6, though. Giving the option for anyone to enjoy the game is always a good thing in my eyes. There is a lot of customizability in the difficulty, with everything from slow-motion reactions to specific assists being offered as toggles. If I had a friend coming over and wanted to try a quick 1v1, the streamlined controls option is one I’d consider to make it a light and fun fight. The one part of the fighting that did not click with me was the grappling. Being taken to the ground brings in an entirely new control mechanism involving mounts and submissions that feel more like quick-time events than the heavy, tactical fighting I had seen so far while standing. The game wants me to hold sticks in certain directions to change the position or pull off submissions, trying to do the opposite actions of the opponent. Even though I tried to get used to this gameplay, it just felt like a momentum killer, and I eventually just wanted to get back on my feet to get back into the action. Legacy and Career It was UFC 6’s career mode that I wanted to play the most when I started it up. I grew up with EA Sports games, and taking my team from the ground to the top has always been my favorite task. UFC 6 has that same option but also offers a more cinematic entrance to the career experience than I expected with ‘The Legacy’ mode. This mini-campaign follows an up-and-coming fighter, Chris Carter, who is attempting to reach the heights his father had reached in the sport. Starting with a small-time gym and coach, the story follows both his growth in the space as well as the growing rivalry with a friend and fighter, Danny Lopez. The fights in this mode are very good at introducing a newcomer like me to the sport and its varying techniques. Cinematics land between the major fights, showing the growing tension between the two fighters as the years go by, feeling the pressure to not miss out on the hard-earned chances. The dialogue can be a little corny at times, especially when the bar fights kick off, but I largely enjoyed the storyline. At the end of it, I was pretty much familiar with all the mechanics of the career mode, unlocking new skills and moves, and how I needed to approach fights, both outside and inside the ring. This story mode isn’t a very lengthy one, so don’t expect an hour-long campaign. Once the conclusion is reached, Carter’s journey continues as if it’s a normal career playthrough, though I decided to start over from scratch now that I have some know-how about the basics. The career mode is very streamlined, which is to be expected considering there isn’t a team to manage like in other EA Sports games. It’s the journey of one fighter. When a fight comes up in the calendar, I could choose how many weeks I dedicate to preparing for it at the gym. A longer prep time gives the opportunity to get my fighter’s fitness up (giving a bonus during fights), earn more money and points for unlocking new skills, and gain more fans to fast-track the rise to stardom. While that sounds like a lot of things to manage, it’s more like a few clicks. There is a social media menu that sometimes pops up with canned replies I can send to fans, and the sponsors are once again a single click away from being assigned as finished. It’s the training aspect that adds a gameplay angle. Using the money from winnings and sponsorships, I was hiring different types of trainers and learning fancier moves to use in the ring. One small thing I appreciated was that it was possible to injure each other during these training sessions. If a trainer goes down in a bad way while sparring, they won’t be available for the remainder of training. If my fighter is injured, it takes valuable time and resources to heal and recuperate. Just like in real life, it makes sense not to go so hard during training sessions and save that energy for the main event. Every training or sponsorship activity I took part in used up the days and weeks I had before the next fight, bringing a balancing element to the whole ordeal. There were times I simulated most of these to just get to the next fight, but the grind for gaining even the slightest bit of advantage while trying not to overdo it is an enjoyable one. Outside of quick fights and career modes, UFC 6 also introduces an almost museum-like mode to explore a trio of fighters considered to be legends of the sport: Max Holloway, Alex Pereira, and Zhang Weili. The aptly named Hall of Legends mode is unlike everything else seen in the game. Each of these fighters has entire levels dedicated to them that I could walk around in and explore their journey into the UFC. This includes footage from real-life fights and interviews about their original inspirations and training methods. Each of these spaces is almost like an interactive documentary. Once the highlights are done, the mode offers the opportunity to take over a deciding fight from the superstars. It’s an impressive transition. Going from the real-life televised event with crowds and commentary to immediately taking over in the game has some real hype behind it. Performance and visuals It’s clear to see that UFC 6 is going for a photo-realism look with its visuals compared to any other fighting game. The fighters don’t look great in selection screens. But inside the arenas, under the flood lights, surrounded by crowds, and facing an opponent, the visuals are more than impressive. As ghastly as it is to witness, things like blood spraying into the mat and muscles reddening as they get pummeled keep improving the immersion. The fluid animations help sell the illusion even further. A missed kick carries the momentum to require a corrective step. Hard punches that glance off blocks give off the air of a hit that still took some wind off the opponent’s guard. The special moves with flips and spins look mega awkward when missing, just as they do in real life. Suffice to say, the Frostbite Engine powering this game is one of the biggest strengths of EA development studios. Playing on the Xbox Series X, the 60 FPS gameplay did not miss the mark or cause any slowdowns that I could detect. I still wish this series were on PC to see just how far the developer can push the engine. One area I continue to have issues with, surprisingly enough, is the menus. The game has fast loading screens, but almost every menu I click through has a large amount of noticeable lag before it registers. This is immensely painful in the career mode, since I have to go through multiple menus between fights to train and do sponsorships, and having a 3-second pause when selecting a simple move between pages is the only time that made me quit the game. Thanks to Xbox’s quick resume, though, I was able to instantly jump back in the next day to the same point (and wade through more laggy menus). Conclusion My primary mission going into this EA Sports UFC 6 review as a newcomer to the series was to find out if this is a good jumping-in point for someone like me. Suffice it to say, the game passed that test with flying colors. Despite the high skill ceiling, the legacy mode introduction campaign, multiple types of accessible controls, and streamlined career had me picking up the basics and fighting styles much faster than I expected. I wish I had gotten to try out competitive multiplayer during my time with the game, too, but the lack of players in the pre-release version prevented this. The impressive visuals and animations, coupled with the impact physics that let me feel every punch and kick easily, made this the most immersive fighting game I have played. The only part that gave me pause was the grappling gameplay, which killed the momentum in most fights. The Flow State amplifying system didn’t hamper the experience, but I also felt like it made more sense for an arcade fighter, not this. Easily the most annoying thing about UFC 6 was its laggy menus, which I hope get some sort of fix later. Returning series veterans might have a completely different experience from me. But for a new fan like me looking to climb ranks and see fighters get floored in spectacular ways, UFC 6 doesn’t miss a step. EA Sports UFC 6 is releasing on June 19 across Xbox Series X|S and PlayStation 5 for $69.99. Ultimate Edition owners can already jump in via advanced access. This review was conducted on the Xbox Series X version of the game provided by EA.
    • No, Microsoft is obviously just spending money on maintaining a product with 0 users.
  • Recent Achievements

    • Week One Done
      ssd21345 earned a badge
      Week One Done
    • Contributor
      MarkHughes4096 went up a rank
      Contributor
    • Dedicated
      jordanspringer earned a badge
      Dedicated
    • Rookie
      Rimplesnort went up a rank
      Rookie
    • One Year In
      Markus94287 earned a badge
      One Year In
  • Popular Contributors

    1. 1
      +primortal
      486
    2. 2
      +Edouard
      173
    3. 3
      PsYcHoKiLLa
      138
    4. 4
      ATLien_0
      94
    5. 5
      Steven P.
      79
  • Tell a friend

    Love Neowin? Tell a friend!