Show us your Workstations! - 2013 Edition

By Chasethebase
in Hardware Hangout

 Share

Recommended Posts

Grand Master

Arceles

Posted
Posted

@Aceles - With a little work, it can be done, even in a small case as that.

 

@LogicalApex - Exactly what I meant.

 

?hm... while I do agree that wire management would look better, the truth is that no air flow is interrupted, in fact, while I do have more fans the noise produced by them is far lower than with my previous case, also temperatures are far improved, here is a photo of the little cable management done (the wires that stand out in the previous photo correspond mainly to only fan connectors)

 

eytu.jpg

 

Also note how the graphics card fits quite precisely and without effort even with the aluminium shroud 

 

tod4.jpg

 

.... and just another pick showing how this motterboard also lets little space for the sound card to fit... and yet it's perfect:

 

fwi7.jpg

 

The sound card in question, creative z OEM version and the GPU:

 

yon9.jpg

 

g9b1.jpg

Grand Master

Mindovermaster Global Moderator

Posted
  • Global Moderator
Posted

Seeing your first picture, you have wires going every which way on and around the board. AFAIK, you are distrupting a lot of air from the front fans.

Grand Master

Arceles

Posted
Posted

Seeing your first picture, you have wires going every which way on and around the board. AFAIK, you are distrupting a lot of air from the front fans.

There is just one front fan, the one shown in the second picture.

Grand Master

Mindovermaster Global Moderator

Posted
  • Global Moderator
Posted

My V2... since the other case didn't have enough fans:

 

7f5z.jpg

 

Do tell me, how do you call that wite managed, look on the right side. Wires are going every which way.

Grand Master

Arceles

Posted
Posted

Do tell me, how do you call that wite managed, look on the right side. Wires are going every which way.

 

I never say that there were cable management, I said however that while the cables look like that they don't obstruct the fans flow, I also make sure that the side panel fans are not obstructed by the cables when I close the case. Air enters from the front panel almost exclusively for the GPU, then the two side panel fans supply air for the CPU, the back fan plus the two upper fans send away the hot air, the fan that it's most obstructed is the second upper fan in the top right, but that's because the whole bd drive is obstructing it.

Grand Master

Jamushroom Veteran

Posted
  • Veteran
Posted

I never say that there were cable management, I said however that while the cables look like that they don't obstruct the fans flow, I also make sure that the side panel fans are not obstructed by the cables when I close the case. Air enters from the front panel almost exclusively for the GPU, then the two side panel fans supply air for the CPU, the back fan plus the two upper fans send away the hot air, the fan that it's most obstructed is the second upper fan in the top right, but that's because the whole bd drive is obstructing it.

Don't you have a front-fan? That's kinda obstructed by the cables so that no cool air can get to the PSU.
Grand Master

Arceles

Posted
Posted

Don't you have a front-fan? That's kinda obstructed by the cables so that no cool air can get to the PSU.

PSU has it's own ventilation, covered by dust filter, below the case.

Grand Master

Jamushroom Veteran

Posted
  • Veteran
Posted

PSU has it's own ventilation, covered by dust filter, below the case.

Yeah but still, having air going around it from the front fan helps it run cooler as well. Plus the front fan adds ambient cooling to the whole case, which is obstructed by the cables.

I don't know if it's possible to hide the wires with that case though, but having the front fan blow through the case is always better than having those cables there. Also, maybe it just looks like there are a lot of cables obstructing the fan? We can't see behind the harddrive so there might as well be more space than cables there.

Grand Master

Arceles

Posted
Posted

Yeah but still, having air going around it from the front fan helps it run cooler as well. Plus the front fan adds ambient cooling to the whole case, which is obstructed by the cables.

I don't know if it's possible to hide the wires with that case though, but having the front fan blow through the case is always better than having those cables there. Also, maybe it just looks like there are a lot of cables obstructing the fan? We can't see behind the harddrive so there might as well be more space than cables there.

 

Front fan runs almost just for the GPU since the GPU "divides" the interior of the case, hence the two side panel fans. PSU has a very nice low blade count fan, which is both silent and pulls enough air for the PSU. Case temperature reaches a minimum of 32? when idle, 39 on normal usage. I think everybody is failing to see how efficient is this case, just because the cables are not "arranged" beautifully. Considering that I have a 120W+ CPU with NB overclocked and a 225W+ GPU (which is overclocked too) and my temps are 47? for CPU under prime95 and 70? for GPU on heavy gaming, I say I have quite good temps on one of the smallest form factors. Also no, front fan isn't obstructed at all, there are cables behind the CPU but they are not in bulk covering the whole fan, at best I say they cover 15%.

Grand Master

Jamushroom Veteran

Posted
  • Veteran
Posted

Front fan runs almost just for the GPU since the GPU "divides" the interior of the case, hence the two side panel fans. PSU has a very nice low blade count fan, which is both silent and pulls enough air for the PSU. Case temperature reaches a minimum of 32? when idle, 39 on normal usage. I think everybody is failing to see how efficient is this case, just because the cables are not "arranged" beautifully. Considering that I have a 120W+ CPU with NB overclocked and a 225W+ GPU (which is overclocked too) and my temps are 47? for CPU under prime95 and 70? for GPU on heavy gaming, I say I have quite good temps on one of the smallest form factors. Also no, front fan isn't obstructed at all, there are cables behind the CPU but they are not in bulk covering the whole fan, at best I say they cover 15%.

We don't see that because we only see the side of the case and judge it off of that. There's probably space behind the harddrive (which is also cooled by the front fan) but because I don't see that, I instantly think there's more cables behind it. If you hadn't seen the case IRL and only saw that photo, I'm sure you'd think it's all cramped as well.

Also, I don't think there are cables behind the CPU because the motherboard is behind the CPU :p I think you meant harddrive ;)

Grand Master

Arceles

Posted
Posted

We don't see that because we only see the side of the case and judge it off of that. There's probably space behind the harddrive (which is also cooled by the front fan) but because I don't see that, I instantly think there's more cables behind it. If you hadn't seen the case IRL and only saw that photo, I'm sure you'd think it's all cramped as well.

Also, I don't think there are cables behind the CPU because the motherboard is behind the CPU :p I think you meant harddrive ;)

Lol, yeah... I meant the harddrive, my bad~ :D

  • 2 weeks later...
Grand Master

Cosmin

Posted
Posted

Ok how is everyone got clean desks? WTF guys! you a men not women make some mess! I would show you mine but not much point, all you will see is a bit of the monitor peaking through some dust and clutter :D

Thought that UK guys are much more..orderly and sensitive to disturbance :laugh:

Rising Star

gxsaurav

Posted
Posted

I have waited my whole life to post in this thread. Today my life long dream is complete. I can rest in peace and do my research on Unicorns.

 

Anyway, I recently upgraded my old PC running AMD APU to AMD FX 6300 along with a new GPU. Here are some pics. Full PC config http://pcpartpicker.com/b/ENs I call it RED.

 

1001904_10152099953988957_1121698112_n.j

 

1077217_10152103491008957_1762582840_o.j

 

1174912_10152186167328957_243659469_n.jp

 

1146154_10152150135898957_987302017_o.jp

Grand Master

tsupersonic

Posted
Posted

It looks good, but could be improved. Could you not connect the fans to your mobo if there are any fan headers? Can you not route any cables behind the motherboard tray? Also if you ever do a PSU upgrade, modular is great. You don't have to get full modular, but it'll help tremendously with cable management. 

Rising Star

gxsaurav

Posted
Posted

It looks good, but could be improved. Could you not connect the fans to your mobo if there are any fan headers? Can you not route any cables behind the motherboard tray? Also if you ever do a PSU upgrade, modular is great. You don't have to get full modular, but it'll help tremendously with cable management. 

 

I have three 4pin fan headers in motherboard. The rear and top exhaust are PWM so they are temperature controlled by the motherboard already. The front and side panel have 4 pin molex connectors which I cannot connect to motherboard hence they are always running at full speed and intake cold air from outside the cabinet.

 

Cable management is an on going process. I open the cabinet every weekend and see what I can do better with the cables. Right now what you see is the most optimized I could get due to length of cables. I could have the pushed some more cables behind motherboard tray but I need them for the 4pin molex connector for front fan. Notice that empty molex connector next to front fan in the picture above, towards most right...that goes in the side panel fan. However, I will see what I can do this weekend. I got a bunch of cable ties with me.

 

Even with this cable management, there is nothing in front of the front intake fan to obstruct air from coming inside. I tested this with coloured smoke too. Air comes from front and side. Side panel throws air at the GPU's heat pipe and CPU cooler's body. Both GPU and CPU suck in cold air coming from the front 200mm intake fan. Hot air is exhausted from top via the exhaust fan. Any residual hot air is exhausted via rear exhaust fan.

 

I just purchased this PSU so not going to upgrade for some years. Modular were over $40 costly here in India so I did not go with that.

This topic is now closed to further replies.
 Share
Go to topic listing

  • Posts

    • Win11Debloat 2026.06.14

      By Copernic · Posted

      Win11Debloat 2026.06.14 by Razvan Serea Win11Debloat is a lightweight, easy to use PowerShell script that allows you to quickly declutter and customize your Windows experience. It can remove pre-installed bloatware apps, disable telemetry, remove intrusive interface elements and much more. The script also includes many features that system administrators and power users will enjoy. Such as a powerful command-line interface, support for Windows Audit mode and the option to make changes to other Windows users. All changes made by Win11Debloat can be easily reversed, and most removed apps can be restored via the Microsoft Store. A full guide on how to undo the changes is available here. Win11Debloat features: Below is an overview of the key features and functionality offered by Win11Debloat. Please refer to the wiki for more information about the default settings preset. Remove a wide variety of preinstalled apps. Click here for more info. Disable telemetry, diagnostic data, activity history, app-launch tracking & targeted ads. Disable tips, tricks, suggestions & ads across Windows. Disable Windows location services & app location access. Disable Find My Device location tracking. Disable 'Windows Spotlight' and tips & tricks on the lock screen. Disable 'Windows Spotlight' desktop background option. Disable ads, suggestions and the MSN news feed in Microsoft Edge. Hide Microsoft 365 ads on the Settings 'Home' page, or hide the 'Home' page entirely. Disable & remove Microsoft Copilot. Disable Windows Recall. Disable Click to Do, AI text & image analysis tool. Prevent AI service (WSAIFabricSvc) from starting automatically. Disable AI Features in Edge. Disable AI Features in Paint. Disable AI Features in Notepad. Disable the Drag Tray for sharing & moving files. Restore the old Windows 10 style context menu. Turn off Enhance Pointer Precision, also known as mouse acceleration. Disable the Sticky Keys keyboard shortcut. Disable Storage Sense automatic disk cleanup. Disable fast start-up to ensure a full shutdown. ...and more. Once you’ve downloaded the Win11Debloat file (Get.ps1), just follow these quick steps: Locate the Get.ps1 script file. Right-click the file and select Run with PowerShell from the context menu. If prompted by User Account Control (UAC), select Yes to grant the script the necessary administrative permissions. Win11Debloat 2026.06.14 changes: This is a minor release that hopefully addresses the false positives in Windows Defender and Bitdefender that prevented users from downloading and/or running Win11Debloat. Refactor Get-RegFileOperations.ps1 to address false positives by @Raphire in #626 Add logging around WinGet app retrieval and increase timeout to 20s by @Raphire Download: Win11Debloat 2026.06.14 | Open Source View: Win11Debloat Home Page | Screenshots 1| 2 Get alerted to all of our Software updates on Twitter at @NeowinSoftware
    • what other retro software do yall use

      By C:Amie · Posted

      Still using Microsoft Money 2005 in 2026 here!
    • what other retro software do yall use

      By +Eternal Tempest · Posted

      I have a couple to mention, and they still run great on Windows 11 Adobe Lightroom Version 2 Alcohol 120% CLZ Book, Comic, Game, Movie, & Music Collector (PC - No longer sold / Grandfathered in - now mobile apps/online only) DVDDecrypter ISO Buster Pro version 1.9.1 (Still supports HD-DVD too) Nero Burning Rom 8 (Only the burning software, no backup, media converter, etc)   OpenAL (Runtime) - GuildWars 1 Reforged still uses it for 3d headphone audio PowerDVD 12 Ultra SPTD (SCSI Pass through Direct Driver) UltraISO Windows Media Encoder 9 WinImage You can tell I still sport an optical drive    
    • Linux 7.1 arrives with an NTFS overhaul and major hardware performance boosts

      By zikalify · Posted

      Linux 7.1 arrives with an NTFS overhaul and major hardware performance boosts by Paul Hill The founder of the Linux kernel has just announced the availability of Linux 7.1. This is a stable version of the kernel that will now be tested by various Linux distributions before it is shipped to users through update managers. Some users, like those on Debian, for example, might not get it for a long time, if at all, while Fedora users can expect it in the near future. With Linux 7.1 out on time, the merge window for Linux 7.2 is now open, giving contributors the opportunity to send in major new features that have been waiting for the last two months. Torvalds warned that he is currently travelling and will be in another timezone, so timing for the merge window may be irregular due to timezone differences and limited internet access. Torvalds said that he has already fetched early pull requests to allow him to do some offline work, but the travel could still cause disruption. Right now, he is not planning to extend the release, but did consider it. He said he might later regret not extending, though. In terms of this last week of development for Linux 7.1, Torvalds said there were no major or alarming changes. This week consisted mostly of smaller driver updates to GPU, networking, and sound, networking fixes, trace tooling fixes, and misc minor fixes. The shortlog this week lists fixes for driver bugs, memory leaks, I/O and USB fixes, networking and RDMA fixes, DRM/graphics fixes, and tooling and verification improvements. Specific fixes include USB series heap-overflow and buffer overflow fixes, and multiple use-after-free, memory-leak, and refcount corrections across subsystems such as i2c, zram, gpio, and net. There are fixes for graphics drivers, including amdgpu, i915, and virtio, as well as hypervisor and virtualization tweaks affecting mshv, vmbus, and hyperv. According to Phoronix, anyone running Linux 7.1 should look out for the new NTFS driver, Intel FRED for improved performance on Panther Lake and future CPUs, faster graphics with Intel Arc Battlemage, and improvements for older AMD Radeon GPUs. If you are running Linux on your computer and everything is fine, then you don’t need to worry about updating to Linux 7.1 as a priority; just wait for it to be pushed to you. If you have tried Linux on hardware but it didn’t work properly, trying again with a distro that uses Linux 7.1 could cause Linux to work on your machine, thanks to the new hardware support.
    • Microsoft hides these secret Windows 11 performance boost settings available on every PC

      By contevo · Posted

      you can also do this with this tool: PowerSettingsExplorer made by mbk1969 at 3dguru forum.. I found it by accident researching on modern standby and annoying quirks of it in 2022

  • Recent Achievements

    • Week One Done
      Jeroen Wilms earned a badge
      Week One Done
    • Week One Done
      rolfus earned a badge
      Week One Done
    • One Month Later
      Leroy Jethro Gibbs earned a badge
      One Month Later
    • Conversation Starter
      flexorcist earned a badge
      Conversation Starter
    • One Month Later
      AndreaB earned a badge
      One Month Later

  • Popular Contributors

    1. 1
      +primortal
      507
    2. 2
      +Edouard
      197
    3. 3
      PsYcHoKiLLa
      139
    4. 4
      ATLien_0
      90
    5. 5
      Steven P.
      81
    Show More

  • Tell a friend

    Love Neowin? Tell a friend!