Russian Zenit rocket with US satellite fails at launch


Recommended Posts

Russian Zenit rocket with US satellite fails at launch

A Russian rocket carrying a US-made telecommunications satellite has plunged into the Pacific Ocean shortly after launch.

_65642720_65642719.jpg

Intelsat-27 was to have provided mobile broadband and video services

The Zenit-3SL rocket, which was being operated from a floating pad south of the Hawaiian islands, failed 40 seconds after the lift-off at 06:59 GMT.

The Intelsat-27 satellite was due to be positioned over the Atlantic to provide services to the Americas and Europe.

Officials say no-one was hurt as a result of the incident.

Staff from the Sea Launch company, which organised the launch, direct all missions from a support vessel that sits at a safe distance of about 6.5km uprange of the platform.

The firm said it would establish a review board to determine what went wrong.

"We are very disappointed with the outcome of the launch and offer our sincere regrets to our customer, Intelsat, and their spacecraft provider, Boeing," Kjell Karlsen, president of Sea Launch AG, said in a statement.

"The cause of the failure is unknown, but we are evaluating it and working closely with Intelsat, Boeing, Energia Logistics Ltd and our Zenit-3SL suppliers. We will do everything reasonably possible to recover from this unexpected and unfortunate event."

Sea Launch had not long returned from Chapter 11 bankruptcy protection.

A spectacular rocket failure on its converted oil rig in 2007 forced the firm to restructure its finances as orders slowed and debts mounted.

It re-emerged in 2011 and had lofted four satellites successfully from the Odyssey platform before Friday's loss.

The rig-######-pad and its command ship are based at Long Beach, California.

For a mission, the pair move south to the equator at 154 degrees West Longitude.

An equatorial launch location gives a rocket a boost from the Earth's rotation, meaning it can lift heavier payloads into orbit.

Sea Launch is owned now by a Russian-led consortium headed by Energia Overseas Ltd, and is headquartered in Bern, Switzerland.

The commercial market for launching large geostationary telecommunications satellites is intensively competitive.

It has been dominated for several years by the European Ariane rocket, operated by Arianespace, and the Russian Proton vehicle, which is sold by International Launch Services (although the latter has experienced a number of failures of its own recently).

Once the cause of Friday's loss is identified and any necessary corrective action taken, Sea Launch will need to re-instil confidence in the market that its product is a good one.

The Ukrainian-Russian Zenit-3SL vehicle has a generally good reliability record.

A modified version, the Zenit-3SLB, is operated from land, flying out of the Baikonur Cosmodrome in Kazakhstan. The most recent of these launches was at the end of 2011.

Launch contracts from the Luxembourg-based Intelsat company had been integral to Sea Launch's return to business after bankruptcy protection.

Intelsat-27, which weighed some 6.2 tonnes at launch, was to have provided direct-to-home TV services and mobile broadband connections.

Source

ied1176e336117b54a798eb2295fb0187_satellite-rocket-pacific-ocean.n.jpg

iad7e4767c23688f56264083017f018d6_1.jpg

ic0083d0fc472d37747d41c82ec7fd272_1.jpg

Each launch is separately insured with the rate depending on the reliability and cost of the vehicle + cost of the satellite but on average $15-30M. Additional coverage can be purchased to cover the loss of a satellite once it's in orbit - about another $20M.

A Soyuz or Atlas V launch is insured rather reasonably vecause of their track record, and Falcon 9's low cost and now proven engine-out capability (last launch lost an engine and kept flying because it was designed to do that.)

I wouldn't want to even see the bill for the Proton with a Briz-M upper stage as it's had serious problems for 2 years, and another launch attempt is later this month. Another Briz-M problem and Russia may have to self-insure it.

I can just imagine for the company that lost their spacecraft that a lot of stuff would get pushed back now that they will have to rebuild the spacecraft. and some of those can take 3 or more years to build.

The engine is the RD-171, an evolution of the RD-170 that was used on Energia. A pretty good engine, following the Russian pattern of a single turbopump driving multiple thrust chambers of which it has 4 (when counting rocket engines you count the turbopumps, not the chambers.)

The problem with a shared turbopump vs discrete ones is that one pump failure takes out the entire cluster, which is why Falcon 9 uses one pump / chamber - it gives them an engine-out capability, meaning it can lose 2 engines (rare) and still make orbit.

That said, most launch failures are not due to an engine failure. More often is the avionics failing, a staging issue (ex: stage doesn't separate when it's burned out), a structural failure or the payload fairing fails to fall away.

RD-171

RD-171M.jpg

Engine shutdown at T+ 25 seconds. Accident review board impaneled, and indications from NPO Energomash that it was off course almost immediately. Could be guidance / flight control or engine failure. Time will tell.

This is the 4th failure in 42 flights for Zenit 3, a failure rate of nearly 10%. This classes Zenit 3 as an unreliable launcher. The overall Zenit 2 and 3 is now 15% - 12 fails/partial fails in 80 flights.

Not good for Russia as because of the Proton problems several launches were going to be transferred to Zenit 3 until Proton's sorted out. That plan's now in question. The Soyuz isn't an option for many of these flights as it has a much lower mass to orbit.

Any bets SpaceX and ULA get a slew of calls?

The SpaceX engine design makes more sense to me.

The capability to lose 2 engines, and still make orbit is extremely exciting. What's the failure rate on them so far?

I'm really interested in seeing the falcon heavy. Anyone know when its due to launch?

As for the Russian's... This doesn't look promising. They will lose contracts if they don't figure out how to make them more reliable.

Angara's RD-191 is based on the RD-171 (Zenit) and its parent the RD-170, plus it will use both the Briz-M and Briz-KM upper stages, all of which are having troubles (KM because its to be based on Briz-M.) Not encouraging.

Falcon 9 v1.0 has had 4 launches, all of which put their primary payload into orbit. The last Falcon 9 v1.0 lost an engine but compensated by shutting it down and automatically burning the other 8 and 2nd stage longer. No human intervention needed. A secondary payload from ORBCOMM was sacrificed because of constraints imposed by NASA; SpaceX calculated a success probability for it at 95% and NASA wanted 99% and they were the primary contractor.

Falcon 9 v1.0 has its last launch March 1, another flight to the ISS, and it will be succeeded by Falcon. 9 v1.1 after that; 40% taller (227 ft), up to 55% heavier payloads and sporting an upgraded & much more powerful engine. Engines will be arranged with one in the center and 8 in a surrounding octagon for better load distribution.

Falcon Heavy ships to their new Vandenberg AFB SLC-4E launch site at the end of this year. Before it flies the new Falcon 9 v1.1 flies first, probably in March 2014, carrying a Canadian payload. FH shortly after. The FH payload is unknown.

Update: looking like the guidance system failed - the Zenit turned South immediately after launch instead of the required Easterly heading. The engine shutdown was automatic and part of the Flight Termination System Russian launchers use (US & European launchers are blown up in the air so the fuel is dissipated before impact.)

http://www.spacepolicyonline.com/news/another-russian-launch-failure-sea-launch-zenit-rocket-fails-at-launch

This topic is now closed to further replies.
  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Posts

    • Russia was able to invade Crimea because of those people. But my point is that I've personally heard how great it was to be "back in Russia" right afterwards - look how great it is now. I've asked you a question in another comment which you haven't answered, so I'll ask it again: is it better now without "Europrats"?
    • ZimaBoard 2 1664 Starter Kit review: it's a cool and affordable DIY NAS by Steven Parker IceWhale Technology reached out to me asking if I was interested in testing the ZimaBoard 2, and after convincing them to send me the Starter Kit, it arrived at my doorstep in May. A bit of background: it is a Shanghai-based Chinese company founded in 2020, which specializes in single-board servers and personal cloud solutions. From searching around online, user feedback on the company and ZimaOS is mostly positive, so we're off to a good start. In addition, I should probably point out that although they do not have a large portfolio of NAS devices, with just four of what they do offer, they seem to have covered everything from a relatively low-priced entry point with the ZimaBoard 2, right up to the high end, with the ZimaCube 2 Creator Pack that even includes an NVIDIA RTX PRO 2000. Anyway, as already mentioned, what we have today is the ZimaBoard 2 Starter Kit, and here are the full specifications: ZimaBoard 2 Model 832, 1664 CPU Intel Core N150 (4x E Cores/Threads, Max burst up to 3.6 GHz) TDP: 6W (Base) 10W (Max) Graphics Intel UHD Graphics 24 EUs (1.00 GHz) Memory 8 GB, 16 GB DDR5 4800MT/s non ECC SODIMM (soldered) Disk Capacity 60 TB (30 TB x 2) Supported RAID Types TRAID, TRAID +, RAID0, RAID1, RAID5, RAID 6, RAID 10 Storage 2 x SATA 3.0 6Gb/s Ports with Power Bootloader 32 GB, 64 GB eMMC Network 2x RJ-45 2.5 GbE PCIe 1 x PCIe 3.0 (via LPC) USB Ports 2 x USB-A 3.1 (5 Gbps) Display Mini-DisplayPort 1.4 (4K@60Hz) Hardware Transcoding Engine H.264, H.265, MPEG-4, VC-1 Maximum resolution: 4K (4096 x 2160); Maximum FPS: 60 Virtualization Intel® AES New Instructions Intel® Virtualization Technology (VT-x) Intel® Virtualization Technology for Directed I/O (VT-d) Size (H/W/D) 140mm x 83mm x 31mm Weight 0.4 kg (only ZimaBoard 2 device) Power 12v 5A Power Supply Warranty 1 year (Global) 2 Years (EU) OS ZimaOS v1.6.1 MSRP $339, $399 ($548.60) As you can see above, there are two variants of the ZimaBoard 2. The lesser variant has half the eMMC storage and 8 GB less RAM, although it also costs $60 less than the top variant we are testing today. The above pricing is only for the ZimaBoard 2. I put the MSRP of the Starter Kit next to it in brackets, although as of publishing, it is discounted to $534.50. The ZimaBoard 2 started life on Kickstarter and shipped to backers in August last year. It became available via the official website in late 2025 and Q1 2026. This hobbyist NAS contains the still relatively new N150 Intel CPU released in the first quarter of 2025, with support for DisplayPort 1.4, HDMI 2.1, although in this case, the memory is integrated into the board itself, so it will not be possible to upgrade or expand the amount. It also supports AV1 decoding, as well as H.264, VP8, VP9, H.265 (8 bit), and H.265 (10 bit). The different capabilities in the Alder Lake-N (and Twin Lake) series are listed below. Processor E-cores L3-cache Turbo clock GPU GPU-clock TDP Intel N355 8 6 MB 3.9 GHz 32 EUs 1.35 GHz 9 W Intel Core 3 N350 3.9 GHz 1.35 GHz 7 W Intel Core i3-N305 3.8 GHz 1.25 GHz 9 W Intel Core i3-N300 3.8 GHz 1.25 GHz Intel N250 4 3.8 GHz 1.25 GHz 6 W Intel Processor N200 3.7 GHz 0.75 GHz Intel N150 3.6 GHz 24 EUs 1 GHz Intel N97 1.2 GHz 12 W Intel Processor N100 3.4 GHz 0.75 GHz 6 W The CPU is part of the Twin Lake series that sits near the bottom of the N-series, designed for low- powered systems and entry-level laptops, and as such has a base level TDP of just 6W. As I have noted before, we are seeing another NAS with a great amount of RAM. It's important to mention that the ZimaBoard 2's memory is integrated into the base board (which is why they have two variants of it). As a reminder, up until a couple of years ago, it was commonplace to only get 2 or 4GB max on a flagship Synology or QNAP home NAS. Ever since the likes of TerraMaster and more have entered the market with ample RAM sizes included in their NAS offerings, it has gone a long way in forcing the hands of the traditional makers to up their game a bit. First impressions The Starter Kit came in one outer box with several packages inside it (shown above). I forgot to take pics of it because when it arrived, it wasn't clear what was inside, and I had to confirm with my contact that I received the entire Starter Kit. In the box ZimaBoard 2 ZimaBoard 2 HDD Expansion Bracket + PCIe card frame Zimaboard Mini DisplayPort Male to HDMI Female Cable 4K 60Hz Zimaboard PCIe 3.0 x4 to Dual NVMe M.2 SSD Adapter Card Quick guide [full online guide] Limited warranty notice Screws Design Where to start? You'd be forgiven for mistaking it as an SSD enclosure if not for all the ports on it. It is completely made out of metal, and the top is an entire heatsink. It has a premium feel about it, but it definitely looks like a hobby device. As you will see, the completed build looks like it belongs in a server or meter closet rather than as a showpiece on someone's desk. On what I am calling the rear, there's a Mini DisplayPort (1.4), two 2.5 GbE ports, with Type A 3.1 USB ports, and then the barrel connector port. Around the front, there are two SATA6 ports with a power connector in the middle. Left side Right side One side is completely free of ports. On the other there's a slit that allows for the feed of a CPU fan cable, and a PCIe 3.0 X4 slot. Top Bottom The top is entirely made up of a heatsink except for the extended height for the I/O on the rear. Around the other side, you can find the ZIMA branding and some regulatory information stamped near the bottom. As you may see from the bottom of the ZimaBoard 2, it scratches quite easily from just moving it around on my Ikea island. Teardown Before we get started, let's have a look at this thing on the inside. The steps to get to the board are as follows: Remove the four smaller Torx screws on the bottom of the ZimaBoard 2; Remove the four larger Torx screws on the sides of the device; Carefully unstick the CMOS battery from the PCB; Remove two Phillips screws on the PCB; Lift out the PCB. Yes, as you can tell from the instructions, you need three different tools to remove Torx and Phillips screws (10 in total), and unhelpfully, one of the screws is located under the CMOS battery, which is stuck onto the PCB. Building Now comes the fun part. Because the ZimaSpace website does not provide any guidance on how to put the Starter Kit together. They only have guidance for connecting the CPU fan. However, they did upload a video to their YouTube channel that shows the entire process. To install the fan, first remove the four screws on the bottom of the ZimaBoard 2, then on the inside, there is a CPU FAN connector where you can attach the fan, reattach the ZimaBoard 2 frame, and feed the fan cable through the provided slit. Then remove the nearest screw on the side and attach the fan frame to the side of the device using the same screw. ZimaBard 2 screws Aligning the screws Bottom view Remember those four screws we removed to access the CPU FAN? Longer screws are provided in the box with the HDD Expansion Bracket, which is what you will now need to attach the ZimaBoard 2 to it. Helpfully, the orientation on how to attach it is made obvious when the frame can only be screwed on at the same overall length as the ZimaBoard 2. If you do it the wrong way around (which is what I did initially) one side hangs off the frame, and it becomes difficult to attach the PCIe Adapter Card cable. PCIe card frame Other side PCIe slot connector Next, it's time to attach the PCIe card frame, which is fastened with the help of 3.5-inch SATA HDD (3 screws). These are toolless screws that you can just use your fingers to fasten them with. Then it is time to connect the provided PCIe cable with the slot connector on one side of the ZimaBoard 2, feed it through the bottom of the HDD frame, and fasten it with two standoffs. Both bracket options 2280 standoffs with 2x 4TB MP44Q The PCIe 3.0 X4 card comes with a short bracket option, handy if you decide to place it inside a different NAS or rack server, but here we need the long bracket. Oddly enough, the M.2 standoffs were preinstalled into the 22110 position, but extra standoffs are included in the box, which I installed at the 2280 position for our use. I added a couple of MP44Q M.2 PCIe 4.0 SSDs (2 x 4TB) that can be availed on Amazon for $478.99 (the lowest price for 3 months) that TEAMGROUP supplied us with Then we have the almost completed build, you just need to push the card into the PCIe slot. Unfortunately, IceWhale Technologies did not provide a screw for the PCIe card frame (this is also apparent in their own video). Here it is at several different angles, with the last pic showing the SATA Y-Cable connected to the two WD Red Plus 4TB drives. Setup and Usage Next, you connect your cables to the I/O, and the ZimaBoard 2 powers on automatically, as there is no power button on the device. Power is controlled through the Settings in ZimaOS. BIOS The ZimaBoard 2 includes an Aptio BIOS from American Megatrends [1, 2, 3], and you can setup pretty much everything here including the boot order, which is locked to the UEFI OS, however above that choice you can enable or disable booting to a SATA/USB bootloader so this would still allow you to switch to an alternative bootloader and boot from it, or disable it to instead always start from the first disk with an OS installed on it. Initial Setup Upon connecting to the LAN and booting up, the ZimaBoard 2 can be reached by navigating to the IP address (shown if you have a monitor connected), or you can find it using the ZIMA Client desktop application, which is essentially a Zima device finder. Initializing the ZimaBoard 2 The ZimaOS setup process is pretty straightforward, through a wizard, and in full above, it basically consists of setting up an account and some handy tips, and that's that! Post Setup (ZimaOS update) Upon first boot, you are alerted that there is a ZimaOS update from 1.5.0 to 1.6.1, which I applied; the full process is shown above with the changelog. ZimaBoard 2 Storage Setup Next, it is time to set up the storage. ZimaOS actually throws everything onto the eMMC flash drive; it is also the default location of AppData, which is definitely something to be wary about, as the 45GB available storage could fill up quickly. HDDs I first attempted to create a Storage Pool using the two 4TB WD Red Plus NAS drives, and got an error message: After several attempts and then looking online, I discovered it was a bug with ZimaOS where the fix was simply to reboot ZimaOS and then try again, this time I was able to create a RAID mirror using the two drives. SSDs I did the same for the SSDs, as you will see in the above gallery, when I created the second Storage Pool, it only allowed me to select available drives. ZimaBoard 2 AppData ZimaOS comes with an App Store that includes a repository of almost 400 apps, so you will be able to find most of what you'll need for a NAS (although after a quick search, I wasn't able to find a Surveillance Manager), and now comes the important part: moving the default AppData location off the 45GB eMMC and onto a larger volume: Open Settings Then Apps Then, in the Select a new location field, click on the new Storage volume you want to move it to (in my case, the Apps Storage Pool), which is the SSD RAID mirror. Confirm the Migration warning Be praised! You can also do this for Docker (which by default installs onto the 45GB eMMC flash drive) and the User database. Plex Setup Next, I tested the configuration by installing the Plex Server app from the App Store. The library folders must already exist (which I placed into the Storage Pool). Plex Server setup is straightforward and requires very little configuration. In my case, all I had to do was add the media path I just created, which you can also browse to using the folder icon in the path field. In addition, you can now map the new Media library in Windows Explorer using the Zima Client. Oddly enough, it is not possible to access the ZimaBoard 2 over the Network Neighborhood; you must map drives using the client, which is shown in the last image in the above gallery. I watched one of my Blu-Ray rips, which is Dolby Vision with Dolby Atmos, and the content played fine with no stuttering or buffering, which is what anyone needs in this scenario. ZimaBoard 2 Zima Client mobile app There's also a client for mobile. It is pretty barebones, as shown in the above gallery, for example, the Apps screen launches the WebUI for that app, and the Backup must be done manually. On opening Backup, you can select internal storage folders on your phone to backup to the ZimaBoard 2's storage, and although this is constantly scanned, the backup action itself must be manually triggered. There is an option to allow foreground backup (last image in the above gallery), but this basically means the queued backup gets triggered when you manually open the app. Benchmarking SATA PCIe 3.0 X4 A CrystalDiskMark test on a mapped network drive from within a Windows 11 25H2 PC (image above) connected over a 2.5 GbE was well within acceptable ranges. Writes were generally better on the SSD RAID mirror. SATA PCIe 3.0 X1 I also ran the NAS Performance tester, which tests the link speed performance. As you can see, it pretty much maxes out the 2.5GbE connection. Of course, you can also opt to bond the two 2.5 GbE connections for a bit more umph, but I didn't do that. Thermals Top PCIe card SATA HDDs Next, I measured some hotspots while playing content on Plex. It's fair to say this will perform better than a NAS that is enclosed in a metal or plastic case, as almost everything storage-wise is exposed! Anyway, the ZimaBoard 2 did not break a sweat with Plex streaming or disk benchmarks. ZimaOS Factory Reset ZimaOS does not include a factory reset option. Instead, you have to download the ZimaOS image and flash it to the eMMC manually. The flashing process is shown in the above gallery. The steps to do so are listed below: Download the ZimaOS image here; Open BalenaEtcher (Run as Administrator) and select the image; Select your inserted USB drive (min 8 GB) Flash to it; Connect your USB drive, monitor, keyboard, USB hub (optional), mouse (optional), and network cable (recommended) to the ZimaBoard 2; Connect power and press F11 continuously; Select your USB drive starting with UEFI in the boot device menu; Press Enter on the Install ZimaOS option; Select /dev/mmcblk0 (MMC) flash drive as target; Confirm with (three times) to wipe the target disk; Wait a couple of minutes while ZimaOS installs; Remove the USB drive and confirm with a reboot; Your ZimaBoard 2 has been factory reset. However, you don't have to stick with ZimaOS, in fact the company also offers official CasaOS images, that are based on Debian; or as they say themselves, put anything you want on this "hackable single board server" it's up to you. Conclusion I had a lot of fun putting this together. I've custom-built all my own PCs and servers since the 90s, and this is the first time I have had to put a NAS together. Even if the actual base ZimaBoard 2 was already a completed build, it still feels pretty custom. I just wish that IceWhale Technology included a getting-started guide in the box for the Start Kit, which would have really completed this kit. Instead, I had to search for the official video on the YouTube channel to make sure I wasn't doing anything wrong. So who is this for? Definitely the hobbyist who is comfortable building their own PC and servers. It also has a much smaller footprint than its nearest equivalent (in terms of specs), like the Beelink Me Pro, which is another NAS I will be testing soon. Although the Beelink does not come with the PCIe 3.0 X4 expansion, the ZimaBoard 2 Starter Kit suddenly looks to be a great bargain, even if it only offers the two 3.5-inch bays over the four in the other example. It makes a lot of sense to use Intel's N150 chip inside a NAS; it is more than capable of doing what the ZimaBoard 2 is intended for, media streaming and backup. It also looks like the IceWhale Technology staff are quite active in the official forums helping people with issues they come across with ZimaOS and the devices, peer support seems to be good as well, I was quickly able to find why I was not able to create a new Storage Pool in ZimaOS v1.6.1 even though that is quite a serious bug, hopefully it will be fixed in the next update. If you are comfortable with the command line and Docker, you'll be fine. You can do great things with this hardware. This was my first time with ZimaOS. It seems a bit barebones in comparison to the likes of Synology DSM, TOS, and UGOS, but it has a ton of apps to get you started with your home or small business NAS. Where to buy As of publishing, IceWhale Technology is running a discount of up to 5% for the Starter Kit. If you opt to get just the ZimaBoard 2 itself, it does come with a SATA Y-Cable, so you will be able to connect up to two 3.5-inch HDDs to it. ZimaBoard 2 1668 Starter Kit for $534.50 on Amazon US (was $548.60) ZimaBoard 2 832 Starter Kit for $372.88 on Amazon US (was $390.60) Zimaboard 2 1668 (16GB+64GB) for $419.90 on Amazon US Zimaboard 2 832 (8GB+32GB) for $359.90 on Amazon Disclosure: IceWhale Technology provided a free sample without any editorial input or review pre-approval. Good to know The Amazon link is U.S. specific, and not available in other regions unless specified. We only use first-party seller links (at the time of article publishing); ensure that you purchase from a first-party seller link only. Check out Today's Deals on Amazon | or our recent tech deals. Become a Prime member (for Students or SNAP) via Neowin Get Prime Access - Prime for half price (for qualifying Medicaid, EBT, SNAP) Subscribe to Prime Video, Audible Plus, Music Unlimited or Kindle Unlimited via Neowin As an Amazon Associate, when you purchase through links on our site, we earn from qualifying purchases.
    • It's in the Insider's group so yes it's technically beta, though these days it's hard to see much of a difference unless you opt for the most extreme beta builds, which I don't. When I moved here from the Release Preview channel I did so primarily because I wanted to see how well the restored taskbar functionality (restored from Win10, and earlier) is working and whether it was time to finally abandon SAB--and it is--working fine, so far. Not as polished as SAB, but it'll do for me.
    • I've been using MWB Premium for a number of years so that along with Windows updates and updated browser should be fine. Thanks for that.
  • Recent Achievements

    • Week One Done
      flexorcist earned a badge
      Week One Done
    • One Month Later
      Woland13 earned a badge
      One Month Later
    • Week One Done
      Woland13 earned a badge
      Week One Done
    • One Year In
      bernmeister earned a badge
      One Year In
    • Week One Done
      Scoobystu earned a badge
      Week One Done
  • Popular Contributors

    1. 1
      +primortal
      488
    2. 2
      +Edouard
      220
    3. 3
      PsYcHoKiLLa
      147
    4. 4
      Steven P.
      74
    5. 5
      FloatingFatMan
      70
  • Tell a friend

    Love Neowin? Tell a friend!