Recommended Posts

I do not think you will get anything over that speed that you posted. That router probably doesn't have the cpu behind it to go any faster then the improved speeds that you posted.

 

I suggest using an old pc with two gigabit lan cards and installing pfsense on it.

Lots of things can be done to effect speed get rid of running apps. Stop people from using your network. We have absolutely no clue what is on your PC or network that could cause speed issues. For all we know your computer is hosting a midget porn site while you are downloading petabytes of torrents with or without you knowing.

Majortom, he stated that a tech was able to get faster speeds in his initial post. So I believe it to be an issue with the computer or network

Lots of things can be done to effect speed get rid of running apps. Stop people from using your network. We have absolutely no clue what is on your PC or network that could cause speed issues. For all we know your computer is hosting a midget porn site while you are downloading petabytes of torrents with or without you knowing.

Majortom, he stated that a tech was able to get faster speeds in his initial post. So I believe it to be an issue with the computer or network

HE also posted updated results that show 300/300. I know from experience that a cpu on the router can slowdown throughput.    He didn't say if those 700 speeds are from connected to the router or direct. Smallnetbuilder shows that if the router is serving wireless traffic along with wired traffic its wan to lan throughput drops dramatically.

 

These routers are great for smaller connections  but once anything over 100 gets connected to it you will get bogged down if you do more then 1 thing at a time.

  • 3 weeks later...

Here's the specs including the clock speeds, RAM,FLA, etc on that router:

http://wikidevi.com/wiki/Linksys_E4200

 

CPU1: Broadcom BCM4718A1 (533 MHz)
FLA1: 16 MB (Winbond 25Q128BVFG)
RAM1: 64 MB (Winbond W9751G6JB-3)
Expansion IF types: USB 2.0
USB ports: 1
WI1 chip1: Broadcom BCM4718A1
WI1 802dot11 protocols: bgn
WI1 MIMO config: 2x2:2
WI1 antenna connector: none
WI2 chip1: Broadcom BCM4331
WI2 802dot11 protocols: an
WI2 MIMO config: 3x3:3
WI2 antenna connector: U.FL
ETH chip1: Broadcom BCM4718A1
Switch: Broadcom BCM53115
LAN speed: 10/100/1000
LAN ports: 4
WAN ports: 1

Just checking with the OP what is the advertised Internet Speed package, Link if you will! Have you thought about contention ratios in your building or wherever. I recon you might have made the old school boy error that alot of people do and confuse mbps and MB. Draw us a diagram of your setup... That speed looks VERY good to me especially with a 1ms ping time. Its as if its on your LAN. Heck in my lan building I cant even get 1ms ping times (Using Powerline Adapters however that is)

This is the speeds without the router right now (a bios update made my computer's direct plug much faster)

 

2932292812.png

 

so it's definitely the router. my setup basically goes from the wall to the computer. router comes right in between the two.

 

 

HE also posted updated results that show 300/300. I know from experience that a cpu on the router can slowdown throughput.    He didn't say if those 700 speeds are from connected to the router or direct. Smallnetbuilder shows that if the router is serving wireless traffic along with wired traffic its wan to lan throughput drops dramatically.

 

 

Good catch! that may be the cause of some of the speed loss. I am pretty convinced this is just a limitation of the router and I will need to buy a new one to get past it. although $180 to go from 300/300 to 900/900 isn't really good use of my money right now. 

You can dig up an old computer and build a PFSense box as your router (it can be run in a vm if your system is good enough) if you got good dual GBE ports.Then connect a switch and AP to the "router" and there you go. Budman told me about PFsense and it seems like it would be pretty cool. 

 

I kinda wanna do the same but I'll need to get  new parts for my spare system and I don't got the cash right now :(

You can dig up an old computer and build a PFSense box as your router (it can be run in a vm if your system is good enough) if you got good dual GBE ports.Then connect a switch and AP to the "router" and there you go. Budman told me about PFsense and it seems like it would be pretty cool. 

 

I kinda wanna do the same but I'll need to get  new parts for my spare system and I don't got the cash right now :(

If Budman suggested it I have to look into it. No sarcasm, much respect for his expertise. 

 

after 5 minutes of research

This is very cool....I don't have a spare system with dual GBE ports but will bookmark this for future geeky adventures. 

Well, at this point you have nothing to lose by flashing the firmware to TomatoUSB. I did it to my E2000 and it doubled my throughput. If it doesn't help, you can always flash it back to stock firmware.

Tim

Well, at this point you have nothing to lose by flashing the firmware to TomatoUSB. I did it to my E2000 and it doubled my throughput. If it doesn't help, you can always flash it back to stock firmware.

Tim

nothing to lose?? lol it's giving me 300/300 wired and 100/100 wifi. if i mess up the flash, i will brick it and have to throw out a $120 pos

nothing to lose?? lol it's giving me 300/300 wired and 100/100 wifi. if i mess up the flash, i will brick it and have to throw out a $120 pos

 

No you won't. I flashed my E2000 numerous times from custom firmware, back to stock, and then to custom firmware again with no issues. That is how I finally settled on the Tomato USB firmware I use now. I guess you could possibly mess up by not following the instructions, but most people on this site are smarter than that.

 

Tim

Yeah your going to need a new router that can handle that sort of bandwidth.. Clearly from this benchmark your e4200 can not

 

http://www.smallnetbuilder.com/lanwan/router-charts/

 

post-14624-0-26276100-1379859672.png

 

Sure if you have a spare PC around, or something you can run Virtual then you could run pfsense..  As long as your hardware your running pfsense can handle it then sure it can move 1GB between wan to lan.

 

You can then use your router as just an AP for wireless, where it will be fine.  But routing wan to lan with the tiny cpu and cheap hardware they put into most sohos for under $100 unlikely to be able to handle such bandwidth.  But there are quite a few listed that can do it from the benchmarks look at the link above to find your new router.

 

Now I don't have a gig connection to test with for isp.. I would have to disconnect from internet and put something on the wan  side of my setup that could push out gig to test what my pfsense vm running on a hp microsever N40L could actually do..  Could use my desktop and laptop for sure - maybe I will do that when get a chance.

 

Any questions with pfsense - happy to help.

 

 

This topic is now closed to further replies.
  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Posts

    • Pretty nice tool, thanks
    • Indeed. But note that this has Wifi7, HDMI 2.1, BlueTooth 5.4, and 5G Ethernet, so even in the additional features list this bundle blows the Steam Machine away. And, with the money saved, one could improve this dramatically.
    • One of the strangest galaxies in our Universe could help answer some long overdue questions by Sayan Sen Image by Pixabay via Pexels | Not representative An international team of astronomers led by the Department of Astronomy at Tsinghua University has discovered an unusually metal-poor galaxy that may contain signs of first-generation star formation. The galaxy, named Metal-Pristine Galaxy COSMOS Redshift 3 (MPG-CR3), or CR3, was identified using observations from the James Webb Space Telescope (JWST), the Very Large Telescope (VLT), and the Subaru Telescope. The findings, published in The Astrophysical Journal Letters, describe CR3 as the most metal-poor galaxy known from the period known as "cosmic noon," around 11.5 billion years ago. Cosmic noon refers to a period when the universe was producing stars at its highest rate and galaxies were growing rapidly. In astronomy, "metals" refers to all elements heavier than helium, including oxygen, carbon, and iron. Because CR3 contains so few of these heavier elements, researchers say it closely resembles what scientists expect the earliest galaxies in the universe may have looked like. The discovery is significant because it could offer clues about Population III (Pop III) stars, the first generation of stars thought to have formed after the Big Bang. These stars are believed to have formed from gas made almost entirely of hydrogen and helium, before heavier elements were created inside stars and spread across the universe through supernova explosions. Hence this is why CR3 has been referred to as a "living fossil." Scientists have long believed that Population III stars existed only in the very early universe. As more generations of stars formed and died, they enriched surrounding gas with heavier elements, making the conditions needed for metal-free star formation increasingly rare. Because of this, researchers expected the formation of such stars to have largely ended after the epoch of reionization, a period when radiation from the first stars and galaxies transformed the neutral hydrogen filling the universe and made it largely transparent to ultraviolet light. CR3 appears to challenge that idea. The galaxy was observed at a redshift of z = 3.193 ± 0.016. Redshift measures how much light from a distant object has been stretched as the universe expands and helps astronomers determine how far back in time they are looking. In this case, the redshift corresponds to roughly 11.5 billion years ago during cosmic noon. Although the universe was already several billion years old by that point, CR3 shows characteristics more commonly associated with much earlier galaxies. Observations revealed exceptionally strong emissions from hydrogen and helium, including Lyα, Hα, and He I λ10830. Lyα, or Lyman-alpha emission, is a specific wavelength of light produced by hydrogen and is widely used to study distant galaxies. Hα emission is another hydrogen signature commonly used to trace active star formation, while He I λ10830 is produced by helium and can indicate the presence of very hot, young stars. The measured equivalent widths of EW₀(Lyα) = 822 ± 101 Å and EW₀(Hα) = 2814 ± 327 Å are among the highest ever observed in star-forming galaxies. Equivalent width is a measure of the strength of an emission line relative to the surrounding light, and such large values are typically associated with intense and very recent star formation. At the same time, researchers found no statistically significant detections of metal emission lines, including [O III] λλ4959, 5007 and C IV λλ1548, 1550. Emission lines act as chemical fingerprints that reveal which elements are present in a galaxy. Oxygen and carbon lines are commonly seen in galaxies that have already undergone significant chemical enrichment. Their absence in CR3 suggests an unusually pristine environment. Using abundance calibration methods developed with JWST observations, the team placed a 2σ upper limit on the galaxy's gas-phase metallicity of 12+log(O/H)<6.52, corresponding to less than 0.7% of the Sun's metallicity (Z < 7 × 10⁻³ Z⊙). Gas-phase metallicity measures the abundance of heavy elements in a galaxy's gas. A 2σ upper limit indicates that the true value is very unlikely to be higher than the quoted threshold. Even when accounting for uncertainties in the calibration methods, the most conservative limit remains 12+log(O/H)<6.95, making CR3 the most metal-poor galaxy identified at cosmic noon. The galaxy also appears to contain very little dust. Researchers measured a Lyα/Hα flux ratio of 13.9 ± 2.5, a result that suggests negligible dust attenuation, meaning very little of the galaxy's light is being absorbed or scattered by cosmic dust. Because dust is usually produced by earlier generations of stars, this finding further supports the idea that CR3 has experienced very little chemical enrichment. Further analysis using spectral energy distribution modelling, a technique that compares observed light with theoretical models, suggests that CR3 contains an extremely young stellar population only around 2 million years old. The modelling, which used Population III stellar templates, also indicates the galaxy has a stellar mass of approximately 6.1 × 10⁵ M⊙. The symbol M⊙ represents one solar mass, or the mass of the Sun. One of the key questions raised by the discovery is how such a chemically primitive galaxy could exist in a universe that had already spent billions of years producing heavier elements. To investigate this, the researchers examined CR3's surroundings. Their analysis suggests the galaxy may lie in a slightly underdense environment, with a density contrast of roughly δ ≈ −0.12. An underdense region contains less matter and fewer galaxies than average. The team suggests that this relative isolation may have helped preserve pockets of pristine gas. Metal-rich material expelled from nearby galaxies may never have reached CR3, while the lower rate of galaxy mergers and interactions could have slowed the mixing of enriched gas into the system. If future observations confirm these findings, CR3 could provide some of the strongest evidence yet that first-generation star formation continued well after the epoch of reionization. Such a result would challenge the conventional view that pristine star formation ended by z ≳ 6 and suggest that small pockets of metal-free gas survived much longer than previously thought. Researchers stress that more observations will be needed to determine the galaxy's true nature. Future spectroscopic studies with higher resolution and better signal quality could help confirm whether CR3 is genuinely hosting Population III star formation. The discovery is also expected to encourage searches for other similar galaxies, which could help astronomers better understand how the first stars formed and how galaxies evolved in the early universe. Source: Tsinghua University, IOPscience This article was generated with some help from AI and reviewed by an editor. Under Section 107 of the Copyright Act 1976, this material is used for the purpose of news reporting. Fair use is a use permitted by copyright statute that might otherwise be infringing.
    • "I think in the immediate absence of a partner to apply relief" In the words of Sterling Archer... "Phrasing!"
  • Recent Achievements

    • Dedicated
      HidekoYamamoto94 earned a badge
      Dedicated
    • One Month Later
      timbobit earned a badge
      One Month Later
    • One Month Later
      nates earned a badge
      One Month Later
    • Week One Done
      Almohandis earned a badge
      Week One Done
    • Rookie
      dorf went up a rank
      Rookie
  • Popular Contributors

    1. 1
      +primortal
      454
    2. 2
      +Edouard
      161
    3. 3
      PsYcHoKiLLa
      107
    4. 4
      Michael Scrip
      83
    5. 5
      Steven P.
      70
  • Tell a friend

    Love Neowin? Tell a friend!