My Qualcomm snapdragon 615 device overheating [65-75c]


Recommended Posts

recently i have bought a brand new phone named "yu yureka" from indian manufacturer micromax

Chipset Qualcomm MSM8939 Snapdragon 615 CPU Quad-core 1.7 GHz Cortex-A53 & quad-core 1.0 GHz Cortex-A53 GPU Adreno 405

Internal 16 GB, 2 GB RAM

WLAN Wi-Fi 802.11 b/g/n, hotspot Bluetooth v4.0, A2DP GPS

Yes, with A-GPS

Sensors Accelerometer, gyro, proximity

Nattery: Li-Po 2500 mAh battery

and it supports 4G LTE, dual sim(sim1=4G sim2= 3G)

 

though it have lot of software issues (its similar to 1+1 and uses cyanogen mod os/kitkat 4.4.4 preinstalled) they even said rooting doesnt violate warranty so i rooted too

i found temporary fixes for the software issues also calibrated the battery coz it was draining to 0% straight from 48% everytime and now its fixed

 

the real problem is HEATING.. its a hot stove

 

in pocket = 35-42c

browsing or call, messaging = 45-48C

skype, whatsapp=50-55c

small games=55-58c

kickass games=65-67c and sometimes 69c but soon comes back to 65c

while doing stress test/benchmark it went up to 70c and even stayed @ 75c for a while like when floating no testing.. sometimes it went to 77c during the process

I COULD MAKE OMLET @ THAT TEMP..lol

 

i reported to the officials and they said its NORMAL (?? really??? )

i even set cpu governer to balanced/power saving also set the governing mode to INTERACTIVE.. and underclocked the CPU to between 400MHz to 933 MHz it did reduce the temp by 2-3 degrees but not much..

 

on cpu-z i have noticed that all the 8 cores are always active.. and the speeds are always varying.. one sec it will b 400MHz then within secs it hoes to 800 then soon to 933 then to 600 then back to 933.. its not stable even when no other apps are running

 

is it coz of badly written cynogen mod? or its a hardware issue? or is it really the normal temperature as the officials said?? [ on xda forums i found that ppl said cpu can withstand 100c and cutoff temp is 90c only] i even found that ppl having same issue on htc one, samsung galaxy s4, moto G... so  its the same with all octa core cpu phones?? please help me out guys.. im worried if my phone might explode.. [ps: battery temp is never over 40c.. its always between 32-38c never more]

its probably a badly designed phone that doesn't dissipate heat properly.

 

your phone wont explode as long as you make sure battery never crosses 50C(even then it wont actually explode but then it'll be operating outside normal temperatures and the results are unpredictable).

  • Like 1

yes with stocck OS.. stock OS is cyanogen itself.. this one is the same as 1+1.. cyanogen will directly send the OTA updates..

 

i have tested moto E which have a quadcore processor that one also have the same base temperature as mine but that phone's temperature doesnt cross over 60C but for the same game it went to 68c

 

i called the customer care and they said its NORMAL for this processor and told me to wait for 2-3 days as they are gonna release a FIX.

using cpu-z i have noticed that all the 8 cores are always active and the speed isnt always stabilized it always flexuates between low and high in a increasing then decressing manner within seconds... i observed for 10 secs and within that 10 secs the cps speeds went from 400 mhz then 1.2ghz then 600mhz then 933mhz and then 400 mhz again.. this was going on and on.. so its a OS issue?? may b the OS isnt handling it well??

 

ps: once i have set the low and high speed ranges to the processors to 633 Mhz.. and in cpu-z i found that only 4 cores were set to 633 mhz other 4 cores were going high and low as usual

yes with stocck OS.. stock OS is cyanogen itself.. this one is the same as 1+1.. cyanogen will directly send the OTA updates..

 

i have tested moto E which have a quadcore processor that one also have the same base temperature as mine but that phone's temperature doesnt cross over 60C but for the same game it went to 68c

 

i called the customer care and they said its NORMAL for this processor and told me to wait for 2-3 days as they are gonna release a FIX.

using cpu-z i have noticed that all the 8 cores are always active and the speed isnt always stabilized it always flexuates between low and high in a increasing then decressing manner within seconds... i observed for 10 secs and within that 10 secs the cps speeds went from 400 mhz then 1.2ghz then 600mhz then 933mhz and then 400 mhz again.. this was going on and on.. so its a OS issue?? may b the OS isnt handling it well??

 

Let's hope for nothing out there that can't be fixed .

Nothing certainly yet .

I still suggest you to send it to a repair service .

  • Like 1

now there is a new issue.. phone shuts off itself and wont turn on.. i had to remove and reinsert the battery and then power on to make it work back again... battery isnt draining though ( before calibrating the battery i had the same issue) what else could have the reason now ( the cpu temp was at 55 which is quiqt normal for my device now a days)

Sounds like a lemon to me, this is why I avoid no name brands like this one, it's always a crap shoot, and you generally end up with junk 

 

The saying is true, you get what you pay for, cheap will always be bad 

  • Like 1

 

now there is a new issue.. phone shuts off itself and wont turn on.. i had to remove and reinsert the battery and then power on to make it work back again... battery isnt draining though ( before calibrating the battery i had the same issue) what else could have the reason now ( the cpu temp was at 55 which is quiqt normal for my device now a days)

 

 

It can be software's and even hardware's fault ...

That's usually happens after root + un - root process ...

I observed that all the 8 cores in the processor are running simultaneously without sleeping and this could be the reason for the large heat and huge battery drain.

whatever the power mode(power saving ,balance or performance) the phone is running on all cores. Ideally when no background work or no cpu intensive work is goining on cpu must switch to one or two cores but here with yureka its not happening.It is running on all cores. The problem in kernel should be resolved soon according to CM devs.

 

 

 

 

This issue appears confined to this specific device on cm11. The internal test builds of cm12 for tomato do not have this issue.

  • Like 8
  • 2 weeks later...

i heard so too.. thats y waiting for the cm12's release.. whichis under public beta testing now. i heard the reviews they said better multitasking and no crashing of apps n all.. and no heating issues yet.

 

 

Yes quite correct.

Not sure about battery Info though.

This topic is now closed to further replies.
  • Posts

    • Password Safe 3.72.0 by Razvan Serea Password Safe is a password database utility. Like many other such products, commercial and otherwise, it stores your passwords in an encrypted file, allowing you to remember only one password (the "safe combination"), instead of all the username/password combinations that you use. Once stored, your user names and passwords are just a few clicks away. Using Password Safe you can organize your passwords using your own customizable references—for example, by user ID, category, web site, or location. You can choose to store all your passwords in a single encrypted master password list (an encrypted password database), or use multiple databases to further organize your passwords (work and home, for example). And with its intuitive interface you will be up and running in minutes. PasswordSafe was originally designed by the renowned security technologist Bruce Schneier and released as a free utility application. Password Safe 3.72.0 changelog: Fixed bugs Improved font scale handling - should resolve font size issues on high resolution displays. GH1749 In the Master Password Setup window, "Show Master Password" is no longer truncated on some displays. GH1092, SF1595 Size and position of main window is now correctly restored on scaled displays. SF1630 Keep password expiry date when both password and password expiry are changed; don't clear a non-recurring expiry when the password's changed. SF1628 Custom values can now be copied to the clipboard in read-only mode via Ctrl-C and right-click->Copy Value. New features GH1196 Dark display mode support: Password Safe now supports the system display mode, as well as setting the mode directly via Manage->Options->Display->Display Mode. This change also updates the general "look & feel" of the app to the current Windows theme. Known limitations: The Date picker and keyboard shortcut controls do not switch to dark theme The Customize Toolbar dialog does not switch to dark theme Custom Field support has been added to the more advanced features: Filters XML and Text import and export Comparison, Sync and Merge databases SF938 Custom field values may now be selected by name and copied via a "Copy Custom Field Value..." submenu in the entry context popup menu. SF936 Notes and Custom fields layout now overlap, selectable by tabs, resulting in a more compact and less cluttered layout. SF935 Autotype: Specifying '\v{name}' in the autotype text will cause the corresponding value to be autotyped. Download: PasswordSafe 64-bit | Portable 64-bit | ~20.0 MB (Open Source) Download: PasswordSafe 32-bit | Portable 32-bit View: PasswordSafe Website | Quickstart Guide | Screenshot Get alerted to all of our Software updates on Twitter at @NeowinSoftware
    • Google DeepMind published a document on June 18, 2026, that may be the most consequential admission yet from a frontier AI lab: alignment training alone cannot guarantee that AI agents will remain under human control, so structural containment must be built before more capable models arrive.............. https://www.techtimes.com/articles/318758/20260620/google-deepmind-ai-control-roadmap-when-alignment-fails-defense-depth-takes-over.htm  
    • I've got a SoundBlasterX G6 that I use in my streaming setup. Sounds great to me and I've had zero issues with the ancient software package so far in Win11. That G6 has 7.1, Dolby, fully working SPDIF and since it's a USB device it's outside of my rig so I don't have to worry about EMF distortion. Looks like for now this is a pass for me as I think I have better hardware....
    • How do you connect 5.1 Speakers to this thing?
    • I agree with both of you... It's absolutely imperative that science is completely based on actual proven facts and hard evidence and is not considered dogmatic in any way. Science is not a religion and it will never be, and that's exactly how it's supposed to be.
  • Recent Achievements

    • Dedicated
      JuvenileDelinquent earned a badge
      Dedicated
    • First Post
      DrWankel earned a badge
      First Post
    • Reacting Well
      DrWankel earned a badge
      Reacting Well
    • Week One Done
      Supreme Spray LV earned a badge
      Week One Done
    • Week One Done
      Genuinetonerink- Dubai earned a badge
      Week One Done
  • Popular Contributors

    1. 1
      +primortal
      503
    2. 2
      +Edouard
      170
    3. 3
      PsYcHoKiLLa
      88
    4. 4
      Steven P.
      75
    5. 5
      Michael Scrip
      74
  • Tell a friend

    Love Neowin? Tell a friend!