Recommended Posts

What can fix a motherboard? and What worth repairing?

1 worth repairing electronics? That are being disposable?
From what I saw, manufacturers only provide information to authorized electrical diagrams assists and not for any technician of electronics. What does the manager not knowing exactly what this piece and which put replacement. It may happen many mistakes.


2 which can correct a motherboard? or and what was already and over.
Usually you can fix? Which components?
And when you have a component that can not be repaired, there are cases in which recovery is difficult muti, or no spare parts or impossible places to fix.


3 What kind used plates save for reuse of components?
For example, motherboard is always good store, but what other cards are practically disposable and see no need to save. As pci cards, memory burned, burned cpu, etc.
motherboard repair is good, but not good fix a card pci.

I think older graphics cards are worth repairing, by reballing or changing the memory chips, not really for the sake of the device, but if you are a repair shop it's a cheap way to hone your skills, otherwise the margins are too thin for the resale of this type of repaired products. However litography has shrunk and there is a cut-off generation of products that are way too difficult to fix. CPU/PSU fans/coolers and other such components are always a reusable type of thing.

my question is quite wide, are 3 questions within one.

I need experiences of people who tried to repair any piece of electronic informatics. is it worth the repair, was found easy replacement of components.
I need to answer people who have been through some experience in motherboard repair for example.

someone has tried to fix something related to informatics? what problems and difficulties we saw in repairing a piece of PC hardware?

Replacing whole motherboards, video cards, sound cards, ethernet, usb cards -- yes, it can be worthwhile.

 

Getting in to the diagnosis on bad capacitors, resistors, IC chips --- not usually worth the effort.

 

I don't care to fool with ocilliscopes and soldering.

 

Parts containing gold can be recycled.

I repair motherboards for a living, it's cheaper for the customer if you can repair to board level if you have the skills. There really is no limit to what you can repair on a circuit board, you're only limited by your own skillset. The equipment can be expensive, but it pays for itself in the long term. It's the learning part that takes time. Learning about such stuff as semiconductors, bridge rectifiers, voltage regulators, and switchmode supplies are all things you need to learn where motherboards and computers are concerned.

 

I take great pride in knowing that I'm a repair shop with a difference, I actually repair rather than replace components in computers and all the devices I repair, while other shops just chuck boards out and whack new ones in, but that's easy peasy child stuff, it makes me kinda smug :) You learn by doing, so if you're looking to get started, I recommend good books, and some junk boards. Jestine Yong writes some really good books, I recommend checking him out, he's very plain english and doesn't baffle you. The first thing you need to do, is start learning soldering, without soldering you can't do surface mount repair, never mind pass through soldering. Pass through soldering is where legs of components pass through the board and are soldered on the underside, whereas obviously as the name suggests surface mount is soldered on the component side.

 

As for knowing all about semiconductors and all that, stuff like this takes years to learn, even I'm still learning as technology improves, and I've been doing this since I was a kid, cassette players and AM radios and huge brick phones with tons of wiring inside them were all the rage!

 

1 hour ago, Hum said:

Replacing whole motherboards, video cards, sound cards, ethernet, usb cards -- yes, it can be worthwhile.

 

Getting in to the diagnosis on bad capacitors, resistors, IC chips --- not usually worth the effort.

 

I don't care to fool with ocilliscopes and soldering.

Replacing is the easy bit, is laziness, and can be more costly to the consumer. Just because you don't "fool" with the stuff, doesn't mean it can't be done without a bit of dedication, your post just sounds like, "I can't be arsed, so why should anyone else?"

 

It's very rewarding. Obtaining schematics for motherboards and other PC boards is often the biggest issue, as two motherboards with identical chipsets and components can often be wired differently, or have differing companion circuitry. If you've got the drive, passion and determination, learn, learn, learn. You won't become a master overnight, but once you know electronics there's no limit to what you can fix. I started out fixing computers, now I fix all manner of consumer electronics, from your TV to your washing machine, even vehicle ECU's :)

2 minutes ago, Hum said:

Good for your skills and business.

 

But the average person is not going to want to try and repair motherboard parts.

True, but there's no harm in encouraging someone who does. Where would sport be, for example, these days if everyone said, "Your average person doesn't play sport!!" Don't "assume" everyone is average. People taking interest is what grows something. Most highly skilled people started off as "average" people sometime early in their life. Bill Gates would be a prime example. He got interested in something and made something big out of it.

I do not for one person to know everything.
It does not give to me and many other people who use pc, learn electronics background.
many only know how to use a program on the PC to work. people focus only on their profession.
if I think about learning a lot of electronics, I have to work with it. and not programs, programming and parts of PC software.

I think if I or someone want to study the electronic background, will have to work only with electronic repairs and not to work with computers.
but work just fixing all kinds of electronics and appliances.

I and many others, can only focus on one thing in their profession work. make money in any kind of work.

If you're into electronics repairing, this guy's YouTube channel has a lot of worthy information that gives you an idea of what can be repaired if you are skilled. Hardly something that can be done at home alone at minimum cost, though.

https://www.youtube.com/user/rossmanngroup

stopped reading at: "I need experiences of people who tried to repair any piece of electronic informatics". Informatics? Even spell check knows that's not a proper term. (I majored in computer and electronic repair.....yes, it's more times worth it to fix a 20 cent capacitor, than go out and buy a 200 dollar motherboard. YMMV.) Informatics.....thank you, I needed a laugh today! XD

12 minutes ago, Obi-Wan Kenobi said:

stopped reading at: "I need experiences of people who tried to repair any piece of electronic informatics". Informatics? Even spell check knows that's not a proper term. (I majored in computer and electronic repair.....yes, it's more times worth it to fix a 20 cent capacitor, than go out and buy a 200 dollar motherboard. YMMV.) Informatics.....thank you, I needed a laugh today! XD

just I want to have a same basic concept, I want to at least replace capacitors, and those easiest parts to fix.
I do not want to go as deep into the electronics.

I and many other people, it's not your area is not a sand and beach, being a technician of electronics!
but at least get a sense of what it is, to know a little of everything.

 

25 minutes ago, Obi-Wan Kenobi said:

stopped reading at: "I need experiences of people who tried to repair any piece of electronic informatics". Informatics? Even spell check knows that's not a proper term. (I majored in computer and electronic repair.....yes, it's more times worth it to fix a 20 cent capacitor, than go out and buy a 200 dollar motherboard. YMMV.) Informatics.....thank you, I needed a laugh today! XD

Sorry, informatics is a real word whether your spell check flags it or not. :)

https://en.wikipedia.org/wiki/Informatics

This topic is now closed to further replies.
  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Posts

    • This looks awesome, I will request access via Steam later this afternoon!
    • Personally, I’ve found that it’s usually worth investing in the infrastructure you don’t want to replace later, especially cabling. Running Cat6A (or better, depending on your needs) during an upgrade is relatively inexpensive compared to having to re-cable a few years down the road. For switches I try to balance current specs with realistic growth. If my budget allows it Ill choose switches with higher uplink speeds which leaves room for expanding later on, but I don’t necessarily overspend on access ports if the endpoints won’t benefit from them anytime soon. One lesson I’ve learned is that planning for scalability pays off. It’s much easier to add devices, VLANs, or higher-bandwidth workloads when your network infrastructure already supports it than to replace hardware later.  What is your budget like?
    • I hate the term, "future-proof." We saw it back in the 90's / 2000's, if not before. You cannot future-proof anything, since there is no definition of how far into the future you plan on prepping for. Best idea is to tell us what you currently have and what its use is at the moment, and we can then offer ideas about some areas that might need an upgrade and other areas that can be left alone.
    • I can agree that it is being used in a small capacity. I worked for a company where their engineers still used XP, and when asked why it was because their sensor software wasn't compatible with newer operating systems and the software was discontinued so they couldn't upgrade the software. Given that the sensors were still in use by companies, they had to continue using XP to support the sensor, otherwise the price to the company would have gone into the millions or billions. Our response was simple: Ok, you can keep the XP machine. But we're removing it from the network. "But then it can't access the Internet or folder shares!" Yup, kinda the point. If someone wants to continue using an unsecure OS they can do, I have no problem with that. But it should be isolated. Simple. I had a fight with a guy in the engineering department for weeks before he finally relented. But we digress.   What do I plan on doing to commemorate the anniversary? Nothing. I have fond memories of the OS, but at the end of the day it's just an OS. If I had some time I might see if I could install it on my Raspberry Pi for a laugh. But my reflex memory with today's OS ideas would probably get me frustrated and I'd uninstall it after 5 mins.
    • Shutter Encoder 20.2 by Razvan Serea Shutter Encoder is one of the best video converter software and image, audio available today. It has been designed by video editors in order to be as accessible and efficient as possible. It is one of the few free professional tools. Based on FFmpeg, it has the largest codec library available. You can thus convert your files into many different formats. Complete settings for the most advanced Shutter Encoder has a panel containing a large number of settings, in order to define your own choices based on your files and perfect your video or audio output. Well-thought-out settings, with parameters predefined to create files quickly and easily. List of functions Without conversion: Cut without re-encoding, Replace audio, Rewrap, Conform, Merge, Extract, Subtitling, Video inserts Sound conversions: WAV, AIFF, FLAC, MP3, AAC, AC3, OPUS, OGG Editing codecs: DNxHD, DNxHR, Apple ProRes, QT Animation, GoPro CineForm, Uncompressed YUV Output codecs: H.264, H.265, VP9, AV1, OGV Broadcast codecs XDCAM HD422, AVC-Intra 100, XAVC, HAP....and much more. Shutter Encoder 20.2 changelog: Added "Intel Quick Sync" hardware acceleration for Linux Added 'Identify speakers' option for "Audio transcription" function Improved installer package Improved video player performance Improved timecode display with drop-frame videos Improved naming convention for surround audio files Fixed splash screen freeze Fixed bug with file hanging Fixed bugs with presets loading Fixed bugs with video player's buffer Fixed bug with 'Total length of file' option Fixed bugs with 'Record screen/device' option Fixed bug with "XAVC" & "XAVC Long GOP" functions Rollback to XPDF tool for PDF conversion Removed unused binary architecture for Mac Various corrections Various improvements Download: Shutter Encoder 20.2 | 166.0 MB (Open Source) Download: Shutter Encoder Portable | 185.0 MB Links: Shutter Encoder Home Page | FAQ / Tips | macOS | Screenshot Get alerted to all of our Software updates on Twitter at @NeowinSoftware
  • Recent Achievements

    • Reacting Well
      NovaEdgeX earned a badge
      Reacting Well
    • Week One Done
      NovaEdgeX earned a badge
      Week One Done
    • One Year In
      BA the Curmudgeon earned a badge
      One Year In
    • Conversation Starter
      rosiecharles earned a badge
      Conversation Starter
    • First Post
      KMilenkoski1202 earned a badge
      First Post
  • Popular Contributors

    1. 1
      +primortal
      534
    2. 2
      +Edouard
      265
    3. 3
      PsYcHoKiLLa
      152
    4. 4
      Steven P.
      99
    5. 5
      macoman
      66
  • Tell a friend

    Love Neowin? Tell a friend!