Recommended Posts

Hello fellow neowinians.

 

I have trouble with my router, because it's a provider sample and it's dumb as ********. It's slow and really dumb.

Is there anyway to access devices outside my domain? By factory default router was 192.168.1.1 and since it didn't see devices only some I've changed it, but now I don't see the once which where there when 1.1. This stupid router makes me nuts, is there anyway to access that device without screwing up the currently recognized 192.168.0.X devices? I have to access 1 NAS which is currently stuck in the 192.168.1.X subnet.

 

Pinging not possible, due to I don't know the IP of the NAS. Prev setting was by default dynamic, always set the static IP in router setting. Currently half of the static IP's are correct by router, still executes rules which are not even there in the setting, but had it once.

 

Thanks for helping, probably this is basic IPv4 knowledge, but I really don't know how to make it work, without destroying the current setup.

 

BTW, my network is simple. NET > ROUTER (CABLE+WIFI) > GB SWITCH > 1PC + 4NAS

Link to comment
https://www.neowin.net/forum/topic/1326316-ipv4-basic-network-setup/
Share on other sites

What is the make/model of the router you now have?

 

If DHCP is enabled on the router and also the clients, then it shouldn't matter what IP range (192.168.0.x or 192.168.1.x) as all your devices will work automatically. That said, as you haven't set a static IP on the devices, you should be able to log into the router's web interface and view the connected IP addresses. That will give you the currently assigned addresses. Once you have that info, I would highly recommend setting a static IP on the devices themselves, if you want to ensure they always have the same IP.

 

I'd also consider waiting to hear what @BudManhas to say, as he is very good with networking issues.

 

Yes.

 

Brand is proximus. :p ...but what I can tell the ethernet hardware is "Sagemcom Broadband". But the problem is the firmware, because I have only user access to it and it's a custom one by provider. DHCP enabled ofcourse. Here is the screenshot of current settings:

 

Do i have to change the subnet mask maybe? to 255.255.0.0? And the device missing I cannot see here either. I really haven't experienced anything like this before, not even with cheap routers from TPlink or Dlink.

DHCPv4.PNG

  On 27/03/2017 at 08:25, Class said:

Yes.

 

Brand is proximus. :p ...but what I can tell the ethernet hardware is "Sagemcom Broadband". But the problem is the firmware, because I have only user access to it and it's a custom one by provider. DHCP enabled ofcourse. Here is the screenshot of current settings:

 

Do i have to change the subnet mask maybe? to 255.255.0.0?

DHCPv4.PNG

Expand  

The scroll bar on the right makes it look like there are more options if you scroll down that page? Is there anything useful?

 

Leave the subnet as 255.255.255.0, otherwise you'll enter a whole new world of problems!

 

So it sounds like your devices will have received an address somewhere between 192.168.0.2 and 192.168.0.63. Without having access to the DHCP table, I think you have two options (well, two quick options).

 

1) If you are on Windows, you can use the network discovery feature to find any local devices on your network. Then you can find the IP address and connect to the device to set a static IP

2) Manually try to browse to; 192.168.0.2, 192.168.0.3, 192.168.0.4, etc from your web browser until 192.168.0.63. You should eventually stumble across your devices.

Only the static IP settings are there unfortunately, nothing else

 

I already scanned the network with FING and no, the router did not give an IP to the this particular NAS. Before switching the router to 0.1 i had the NAS statistic router to 192.168.1.58, but erased the line and re-added to give it 192.168.0.3, but it's not being executed. Should I maybe delete the line again, in hope it will pop up in the network. The DHCP of this router is just so baaad. One of my QNAP's I had also this issue, but solved by using the other ethernet slot which was not used before and after 3rd reboot and other ethernet also popped up in the list.

 

What if simply exclude the network and connect the NAS directly into my PC, just to check if dinamic is still corrently set would work?

  On 27/03/2017 at 08:48, Class said:

What if simply exclude the network and connect the NAS directly into my PC, just to check if dinamic is still corrently set would work?

Expand  

Unlikely, as you'd still need to know the address of the NAS to connect to it from the PC.

 

Did you try Window's built-in network discovery?

Yes, did try.

 

I'm not excluding the fact the it could be because of Zyxel firmware (NSA310) is not the most stabil little device, but I restarted many times. Anyway, will to connect it directly and see if I can find the device which the network scanning.

Ok. I am not exactly sure what you are getting at. 

 

I am guessing on the network you have 192.168.1.x and 192.168.0.x. 

 

The 1.x has a router/gateway (your modem) the 0.x has no router/gateway to handle the request to go over to the 1.x network

 

you have to either re ip the network or get a router that can handle other subnets and a switch that can handle what is known as vlans (a layer 2switch).  

 

If your router understands this, technically you could put your subnet mask at 255.255.254.0 (all computers would have to have this mask as well) and then you would see the 0.x and the 1.x addresses. But keep in mind, there is no separation, it is just one big network where the network id is 192.168.0.0 and broadcast is 192.168.1.255. 

If you want to change your network from 192.168.1/24 to 192.168.0/24 and you had devices that were setup static on your network as 192.168.1 - just change them to be on the 192.168.0 network.

 

Either directly on the device.  Or set your machine to be on the 192.168.1 network and access them and change them to 192.168.0 or dhcp.. Then set your machine back to dhcp or 192.168.0 network.

  On 27/03/2017 at 11:12, sc302 said:

Ok. I am not exactly sure what you are getting at. 

 

I am guessing on the network you have 192.168.1.x and 192.168.0.x. 

 

The 1.x has a router/gateway (your modem) the 0.x has no router/gateway to handle the request to go over to the 1.x network

 

you have to either re ip the network or get a router that can handle other subnets and a switch that can handle what is known as vlans (a layer 2switch).  

 

If your router understands this, technically you could put your subnet mask at 255.255.254.0 (all computers would have to have this mask as well) and then you would see the 0.x and the 1.x addresses. But keep in mind, there is no separation, it is just one big network where the network id is 192.168.0.0 and broadcast is 192.168.1.255. 

Expand  

 

  On 27/03/2017 at 12:47, BudMan said:

If you want to change your network from 192.168.1/24 to 192.168.0/24 and you had devices that were setup static on your network as 192.168.1 - just change them to be on the 192.168.0 network.

 

Either directly on the device.  Or set your machine to be on the 192.168.1 network and access them and change them to 192.168.0 or dhcp.. Then set your machine back to dhcp or 192.168.0 network.

Expand  

Today I've played around. And I just cannot figure out what's the issue.

 

I've change back the router to 192.168.1.1 and now I have access to the other NAS, but not the other. It's either one or the other. Checked setting on Zyxel NAS, both are dynamic. And they just simply won't work. One is working if router is set to 192.168.0.1 and the other is working when 192.168.1.1. It's just a complete #WTF moment for me. I cannot think of anything else to check. Restarted the previously accessible NAS, it's just won't show up under 1.1. I'm running out of ideas what can be the problem, and I can only think of 1, the router cannot make a difference between 2 NAS of same type. Both are identical Zyxel NSA310S. Probably thinks MAC information is for noobs and recognizes only 1.

NASv4.PNG

NASv4_11.PNG

If DHCP is refusing to play ball, as a quick fix, decide which network you want to use, let's assume you pick 192.168.1.x, switch your router to 192.168.0.1, renew your DHCP on your pc so you can connect to that network, login to the NAS on that network, and give it a static IP address on the 192.168.1.x network, make a note of what you set it to (and dont set it to something that will be within the DHCP scope of the router). Once that's applied (reboot the NAS if needed, you should lose access to it on the 192.168.0.x network, then change the router back to 192.168.1.x, and renew your lease again to move your PC back, now you should be able to access the reconfigured NAS using the static IP you gave it, and the other NAS via whichever IP it picked up via DHCP. Maybe set that one static and outside of the DHCP scope too, so you always know what IP it will be on, without needing to login to the router to check.

  On 27/03/2017 at 22:50, sc302 said:

One nas is on 0.x and one is on 1.x. One of the two need to be reconfigured on the network.  Assign dhcp to the 0.x one. 

Expand  

 

  On 27/03/2017 at 22:55, DaveLegg said:

If DHCP is refusing to play ball, as a quick fix, decide which network you want to use, let's assume you pick 192.168.1.x, switch your router to 192.168.0.1, renew your DHCP on your pc so you can connect to that network, login to the NAS on that network, and give it a static IP address on the 192.168.1.x network, make a note of what you set it to (and dont set it to something that will be within the DHCP scope of the router). Once that's applied (reboot the NAS if needed, you should lose access to it on the 192.168.0.x network, then change the router back to 192.168.1.x, and renew your lease again to move your PC back, now you should be able to access the reconfigured NAS using the static IP you gave it, and the other NAS via whichever IP it picked up via DHCP. Maybe set that one static and outside of the DHCP scope too, so you always know what IP it will be on, without needing to login to the router to check.

Expand  

Yeah, you just tell the basic thing. Not helping. I did this yesterday. I'm not kidding when I tell, I don't have the goddamn thing. I tried both, letting DHCP give "ball" and "fix ball" I don't have both. I will today swap back to 0.1 and check out once again the other NAS not that I missed any settings.

 

I'm thinking now, could it be the switch who doesn't play along with the router's DHCP?

  On 28/03/2017 at 04:28, Class said:

 

Yeah, you just tell the basic thing. Not helping. I did this yesterday. I'm not kidding when I tell, I don't have the goddamn thing. I tried both, letting DHCP give "ball" and "fix ball" I don't have both. I will today swap back to 0.1 and check out once again the other NAS not that I missed any settings.

 

I'm thinking now, could it be the switch who doesn't play along with the router's DHCP?

Expand  

If you're setting static IPs, then DHCP has nothing to do with it. I'm guessing you just have a dumb switch, so no, that's not going to be interfering with the DHCP from the router. Take some screenshots of the settings page of your NAS when you're in there.

  On 28/03/2017 at 04:28, Class said:

 

Yeah, you just tell the basic thing. Not helping. I did this yesterday. I'm not kidding when I tell, I don't have the goddamn thing. I tried both, letting DHCP give "ball" and "fix ball" I don't have both. I will today swap back to 0.1 and check out once again the other NAS not that I missed any settings.

 

I'm thinking now, could it be the switch who doesn't play along with the router's DHCP?

Expand  

You do know that sometimes you have to reboot the equipment ( in this case the nas) for changes like this to take effect. 

  On 28/03/2017 at 11:21, sc302 said:

You do know that sometimes you have to reboot the equipment ( in this case the nas) for changes like this to take effect. 

Expand  

Reboot counter for device is currently between 20-30 times the last 2 days.

 

  On 28/03/2017 at 07:56, DaveLegg said:

If you're setting static IPs, then DHCP has nothing to do with it. I'm guessing you just have a dumb switch, so no, that's not going to be interfering with the DHCP from the router. Take some screenshots of the settings page of your NAS when you're in there.

Expand  

There is no static routing currently. That what I try to tell. I tried static, I tried dinamic, I tried 0.1 and 1.1. Currently the diagnose is still the SAME. 1 NAS active here, other is active there. So for no one can understand this, not even me.

  1. cables √
  2. switch √
  3. router DHCP dynamic √
  4. router DHCP static √
  5. FING √
  6. zyxel nas setting √

I cannot think anything else anymore. Here is the proof, this is still yesterday setting as 1.1. "CLASS-ZYX" is one nas, and "CLASS-ZYQ" is the one nas. Same type, different name.

IMG_20170328_155306.jpg

Try setting the IP on the NAS itself to a static IP, not on the router. Login to the NAS's control panel, and give it a static IP address on whichever network you intend to use. While you're there, take a screenshot of the network settings applied to the NAS.

  On 28/03/2017 at 14:26, DaveLegg said:

Try setting the IP on the NAS itself to a static IP, not on the router. Login to the NAS's control panel, and give it a static IP address on whichever network you intend to use. While you're there, take a screenshot of the network settings applied to the NAS.

Expand  

I tried that I think on the initial 1st install, but sure, can do and try. But it should work in dynamic routing anyway. BTW, screenshot of NAS is the in one of the previous post.

  On 28/03/2017 at 18:05, Class said:

But it should work in dynamic routing anyway

Expand  

Huh??

 

Your router is not going to to do any dynamic or static routing.. I have read through this thread a few times now and just can get what your issue is..

 

Put your freaking NAS on the same network PERIOD!! 

 

If your your network is 192.168.1/24 or 192.168.0/24 then your 2 nases need to be on the same network as your other devices.  This is as simple as letting them use dhcp or set them static..

 

Do you have your other old router on the network still running its dhcp server?

This topic is now closed to further replies.
  • Posts

    • We went from a Latitude 7450 to Dell Pro 14 Plus PB14250
    • EA Sports UFC 5 is free-to-play on Xbox Series X|S this weekend by Pulasthi Ariyasinghe Every Thursday Microsoft brings in a fresh slate of games for Xbox gamers to try over the weekend as a part of its Free Play Days promotion. The latest refresh that arrived today only revealed a single title for the weekend, and that's EA Sports UFC 5. This is a special occasion as well. Unlike the standard events, this one does not require any tier of Game Pass to jump in. All Xbox Series X|S owners can play the game over the weekend, even if they do not have a Core subscription. As always, any progress made during the weekend also carries over automatically if you decide to purchase the game afterward. Coming in from EA Sports, UFC 5 is the latest entry in the long-running mixed martial arts fighting games. This installment landed in 2023 for the latest generation consoles. Built on DICE's Frostbite Engine for the first time, the title event received an M rating by the ESRB for its realistic injury system, as EA wanted to make a more authentic experience akin to the real-world sport. The damage system, dubbed the Real Impact System, involves depicting blood and sweat on fighters as well as facial injuries. Having injuries like bruised eyes or broken noses can even affect the performance of a fighter due to impaired vision or breathing difficulty. A doctor stoppage may even happen if the injuries become too severe. UFC 5 offers a single-player career mode to become the top-ranked fighter, online modes for competitive action, and special events tied to real-world fights. Here are the store links for the game: UFC 5 - $27.99 (Xbox Series X|S) UFC 5 Deluxe Edition - $31.99 (Xbox Series X|S) UFC 5 Ultimate Edition - $89.99 (Xbox Series X|S) This Free Play Days promotion will end on Sunday, June 29, at 11:59 pm PT. Following this, expect another round of games to enter the program next Thursday, July 3.
    • Windows 11 KB5060826 optional update brings better Setup, new data migration tool, more by Sayan Sen Alongside KB5060829 for Windows 11 24H2, Microsoft has also released its C-release non-security preview update for Windows 11 23H2 and 22H2 today. The new update is rolling out under KB5060826 (builds 22621.5549 and 22631.5549). KB5060826 brings an upgraded Setup which will now let admins choose whether to deploy critical updates during the OOBE (the initial out-of-box experience setup on Windows). Alongside that, it also adds the new PC migration experience on Windows Backup, as well as the default app changes related to the European Economic Area (EEA) region. The full changelog is given below: First up we have the changes and improvements for Gradual Rollout: [App defaults] New! We are rolling out some small changes in the European Economic Area (EEA) region for default browsers through the Set default button in Settings > Apps > Default apps: Additional file and link types will be set for the new default browser, if it registers them. The new default browser will be pinned to the Taskbar and Start menu unless you choose not to pin it by clearing the checkboxes. There is now a separate one-click button for browsers to change your .pdf default, if the browser registers for the .pdf file type. [PC Migration] New! The PC-to-PC migration experience in Windows is starting to roll out. You’ll begin to see the landing and the pairing page in the Windows Backup app, giving you a first look at what’s coming. In the full experience, you’ll be able to transfer files and settings from an old PC to a new one during setup. Support for this feature during PC setup will arrive in a future update. The rollout is being introduced in phases to support a smooth experience. [Windows Share] ​​​​​​​New! When you share links or web content using the Windows share window, you will see a visual preview for that content. Up next, we have Normal Rollout features: [Windows Setup] New! Admins can configure whether a new device gets critical updates during the out-of-box experience (OOBE). The update has a single known issue related to Noto fonts. You can view the support article here on Microsoft's official website. The update can be obtained by clicking on "Check for optional updates" inside Windows Update. You can also download it manually from Microsoft Update Catalog website.
    • American? Yer whole 120v limitation is madness.  You can still get low powered pcs , nice, that'll do the job 
    • People want a resizable taskbar, not tiny icons on a fat one. Microsoft, you've done it again.
  • Recent Achievements

    • One Month Later
      jfam earned a badge
      One Month Later
    • First Post
      TheRingmaster earned a badge
      First Post
    • Conversation Starter
      Kavin25 earned a badge
      Conversation Starter
    • One Month Later
      Leonard grant earned a badge
      One Month Later
    • Week One Done
      pcdoctorsnet earned a badge
      Week One Done
  • Popular Contributors

    1. 1
      +primortal
      571
    2. 2
      ATLien_0
      186
    3. 3
      +FloatingFatMan
      177
    4. 4
      Michael Scrip
      144
    5. 5
      Xenon
      116
  • Tell a friend

    Love Neowin? Tell a friend!