Can beer explode when left in the freezer?


Recommended Posts

Here's the technical explaination:

Taking water for an example, its density is exactly 1. However the density of ice is around 0.8 because of air bubbles that get trapped during the freezing process. Lets say you put this liquid in a closed system (such as a beer bottle). Everyone knows density is weight / volume. Since the weight remains constant (you aren't adding or subtracting anything from the closed beer bottle) that means you must change volume in order to decrease density. Since volume is on the bottom of the divisor it has an inverse relationship. That means you must increase volume to decrease density during the freezing process. We know that a beer bottle can only hold so much volume of liquid, so when that volume starts increasing its going to put pressure on the glass. This is about when it cracks and makes a mess.

I think its mass over volume isn't it? Becuase mass is the amount of matter in a substance which is what actually matters when we are talking about density. However weight is just the mass * the acceleration of the Earth's gravity (Earth in this case) on the substance.

  • 5 years later...

While density is a factor of the "exploding" beer in the freezer as a result of a volume increase, where D=M/V, there are other factors to consider. Factors that would more appropriately determine a time based solution to how long "when left in the freezer" actually is. Yes, a beer will explode in the freezer, but when will it? And, really, at what time should it be taken out in order to enjoy a perfectly chilled beer?

Beer is made of mostly water, and the varying alcohol concentrations--more appropriately the water concentrations--in each different container determine the beer's new freezing point (a result of a freezing point depression calculation). Next, we need to know some information about the system and the surroundings. Such the beer's initial temp, the beer's freezing temp, and the freezer's ambient temp. By using Newton's Law of Cooling (the differential equation) you can determine the time [t] at which the beer has reached its freezing point.

My point being, a beer that was just purchased off the shelf of a blazing hot liquor store, because they were out of cold ones, is going to have a greater change in temperature requirement to reach its freezing point, and is going to take longer to freeze, then a beer that was already in the fridge, but not frozen. (e.g. shelved beer is about 20?C, and refrigerated beer is about 2?C).

-->easier said then done right? nope. you need to perform experiments to determine their "rate constants." This is because each beer, or pop, has different physical and chemical properties. The freezing point depression constant [k] is a little harder to determine and not useful for this application, but for Newton's Law of Cooling, the constant can be determined by solving for [r] after collecting data from the following experiment:

Experiment:

Record the beer's initial temp, and the freezer's temp. Put several of the same beers of the same temp in the freezer at fixed intervals apart in time, and check them periodically. If the beer#1 exploded, then the beer#2 is (interval) away from exploding and you can more precisely monitor the next few, and so on.

Calculations:

Record the final beer temp, and the time it took to reach its final "exploding" temp. Insert the data into Newton's Law of Cooling (the differential equation) and solve for [r]. That way, next time, you can roughly determine how long it will take to perfectly chill that beer without exploding it. Solving for the rate will allow you to use beers of varying initial temps in the future and get a close estimate, but collecting an average rate from varying initial temps would increase the precision for future estimates.

T(t)=Tenv + (To - Tenv)e^(-rt); where: T=beer temp at time t, Tenv=freezer temp, To=initial beer temp.

Now, on to: cans vs. bottles, dark beer vs. ale vs. light beer, twist-off cap vs. pop-off cap...beer vs. pop..:|:|

When I was a kid, my mum left some softdrink in glass bottles in a freezer and the glass exploded. It does this because carbonated drink expands when frozen and will keep on expanding and when there is no room in the bottle, the drink still keeps on expanding and so it pushes the glass out ("exploding it") and keeps on expanding.

It doesn't explode, just the glass cracks open like a hatching egg. Drink might leak and freeze into the floor of the freezer.

the drink expands while being frozen but not enough to cause a explosion (however, it will crack the bottle). as the temperature drops, the ability of the liquid to hold dissolved gas gets lowered. as a result the gas will try to leak out of the liquid and this is what causes the pressure inside the bottle more than the expansion of the liquid itself. now, as for the explosion, it might also depend upon the way the bottles are manufactured from place to place and how they are sealed. a cheaper glass will easily crack and may not cause that big spill or a boom since it wont be able to hold much pressure inside initially before cracking. a better quality glass may be able to hold off for a longer time with a much higher pressure and when it does crack, that excess pressure may cause that boom. similarly, non-screwed on caps can easily be popped of with a slight pressure preventing the explosion as the liquid or the carbonated gas inside leaks out slowly.

This topic is now closed to further replies.
  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Posts

    • Wow, throwback.  VERY VERY briefly - but realised that it wasn't the language I needed for the tasks I was taking on.
    • Apple and Tesla trade secrets reportedly exposed following a Tata Electronics cyberattack by Hamid Ganji Image via Depositphotos.com Tata Electronics has confirmed that it detected a cybersecurity incident in some of its systems. The Indian company is a manufacturing partner of both Apple and Tesla, and the incident may have exposed some trade secrets belonging to the two American companies. The World Leaks ransomware group is said to be behind the attack, and it has reportedly posted up to 200,000 files on the dark web, including component designs and specification documents related to Apple and Tesla products. Tata Electronics told Reuters that its response protocols were deployed immediately and that the “incident has had no impact on our operations across businesses, which remain unaffected.” The ransomware group reportedly sent a ransom demand to Tata Electronics, while Apple has launched an investigation into the incident. World Leaks claims it stole more than 200,000 files totaling over 630GB from Tata Electronics. Some database files on the ransomware group’s website are titled "com.apple.factorydata," which could refer to Apple’s iPhone production operations in India. Moreover, some documents reportedly contain material specifications and quality inspection standards for iPhone circuit board components. However, Apple is not the only affected company. A folder found in the World Leaks database is titled "NV36 Chargeport Controller - North America," which may refer to Tesla Model Y components. Additionally, other files in the database reportedly contain drawings related to Tesla’s Project Highland, the internal codename for the EV maker’s updated Model 3 sedan. To support the authenticity of the stolen files, World Leaks has published documents containing footers that read: "This document contains proprietary and confidential information of Apple Inc." and "information contained herein is deemed confidential, proprietary, and a trade secret of Tesla Inc." Cybersecurity researcher Rajshekhar Rajaharia told Reuters that the database also contains emails, event logs spanning several years, and passport copies of employees, including foreign nationals. Both Tesla and Apple have declined to comment on the scale of the incident.
    • Last time I used Pascal was in college about 40 yrs ago, programmed an inventory database for my exam.
    • If they don't sell enough of the 1st gen then there won't be a 2nd gen
    • Epic fail, should've added an eSata port on the back, also if the memory/NVME are soldered then they're hardly gonna sell any, first thing most people do with their Steamdeck is, or used to be, replacing the NVME with a 2TB one. At that price they should, possibly for the first time, offer an installments option, say 24 months, they may sell a lot if they do. I'm sure they would have no shortage of credit companies willing to partner.
  • Recent Achievements

    • One Month Later
      nates earned a badge
      One Month Later
    • Week One Done
      Almohandis earned a badge
      Week One Done
    • Rookie
      dorf went up a rank
      Rookie
    • First Post
      mike_rumble earned a badge
      First Post
    • Dedicated
      tuben earned a badge
      Dedicated
  • Popular Contributors

    1. 1
      +primortal
      487
    2. 2
      +Edouard
      204
    3. 3
      PsYcHoKiLLa
      95
    4. 4
      Michael Scrip
      91
    5. 5
      neufuse
      71
  • Tell a friend

    Love Neowin? Tell a friend!