[review] Lian-Li PC-V2000B


Recommended Posts

dscn05819oz.jpgdscn06103ov.jpg

dscn06173ug.jpgdscn06207jc.jpg

dscn06235xh.jpgdscn06255wv.jpg

dscn06295au.jpgdscn06310ei.jpg

dscn06436ij.jpgdscn06641cb.jpg

dscn06715jn.jpgdscn06744rr.jpg

dscn06758ux.jpgdscn06766fz.jpg

dscn06939ky.jpgdscn06966tg.jpg

INTRODUCTION

This case wasn't that expensive. 250 bucks from newegg.

BOX

No damage. In plastic bag. Good instructions.

CASE

Painted. Smells like paint for a bit. Very very light. Almost feather light.

The doors prob. weigh more than the case

INSTALL

No probs. The 80mm fan area on the back I had to drill out because

the supplied holes weren't big enough.

Clearance for the doors is tight. They lift up after unlocking uptop.

The 5.25 bays come off (faceplate) with no screws.

The 3.25 bays are solid. Method of install great.

CONCLUSION

As a reviewer on newegg said just buy it don't think.

Link to comment
https://www.neowin.net/forum/topic/441243-review-lian-li-pc-v2000b/
Share on other sites

I don't see how the guy was a jerk, he's right ... you didn't tell us anything interesting. We could have read that information at newegg. Also, if you're reviewing something for people, proper grammar isn't much to ask for. If it wasn't for the good pictures (which was the selling point of your post, certainly not your "review") I don't think I would buy the case... but since the pictures show how nice the case is, I might consider. Now, take this how you want, but just remember, the truth hurts.

my caes too. btw, what screws did u use to install the rear 80mm fans? I had to use rubber silicon fake screws that came with my SilenX fans. I have the V2100 Plus version so not sure if it makes any difference

For some reason the screw holes above the power supply that allow you to secure the fans or a cooling radiator were too small in diameter. I had to take a drill and widen the holes so I could get the screw to go through the hole and attach the fan. I used the screws that came with the 80mm antec fans I bought. They were the standard fan screw, you know with the little notch and about 1 cm long.

I don't see how the guy was a jerk, he's right ... you didn't tell us anything interesting. We could have read that information at newegg. Also, if you're reviewing something for people, proper grammar isn't much to ask for. If it wasn't for the good pictures (which was the selling point of your post, certainly not your "review") I don't think I would buy the case... but since the pictures show how nice the case is, I might consider. Now, take this how you want, but just remember, the truth hurts.

I see what your saying. I know that more explanation would of been good. But I also figured some of the treasures of the case would remain unsaid for the purchaser to discover.

Well... as a reviewer, you are supposed to reveal everything, not to what the end user to discover :)

That's a good point.

Well, here's some more info

AIRFLOW

The case was designed to pull air from the front of the case to the back of the case. There is a single 120 MM fan at the front cooling the HDD array area. This air then passes to the power supply area witch can be exhausted by the power supply or if you want you can install 2 80mm fans above the power supply witch aid with air dispensing.

I'm running 6 sata disks all at 7200 rpm. The temperature is currently 85 deg F in the HDD area.

The upper part of the case I was worried about cooling because there is only a single 120 MM exhaust fan placed below the pci area and adjacent to the io area.

Temps currently are all about 85 deg F, well within range. (The CPU, SYS, and HDD temps.)

HDD MOUNTING

HDD mounting is easy. Attach 4 screws and slide into rail. Then slip down the cover to lock the drive into place. The lock down snap things are plastic and lock well. There are two locks per drive slide.

The nice thing about this is you never have to mess with hdd mounting. Just attach the 4 scews and then slide into place. Removal is equally easy. Just lift the locks, slide out.

:)

5.25 MOUNTING

The upper 5.25 Slot has a CD bezel. The bezel works fine. The button is plastic and the rest of the part metal. The button may be a problem if the drive you are using does not have a standard button location.

Many of these devices extend a plastic bar across the drive/bezel face to hit the button if it's off the regular location. This cd bezel does not have that. Your button needs to be in the right location to get the bezel button to hit the cd button.

The faceplates are not secured by a screw so they are easy to remove with a push of a pencil or something.

The bottom 5.25 area has a floppy cover. This can be removed and the 5.25 faceplates will function in any of the other locations if you wish to rearrange things.

MOBO MOUNTING

The mobo is INVERTED. My power connector is on the top and had to use an extender to reach the connector. The mobo installed with no problems. Had to drill my own standoffs because of the non spec board.

Because I drilled my own standoffs the rear door behind the mobo will not reseat because there is zero clearance. So the case is now running with one door off. This may be reducing temps.

The PCI bay covers are made out of nice metal and not cheap aluminum. The screws for the PCI cards are also nice and heavy not light and flimsy.

This was nice to notice

FIT AND FINISH

The case work is good and the raised power supply is nice. There are many small holes all over the case in pattern mimicing the G5 case. This is nice.

NOISE

Since I removed the adda fans I don't know how it would be a stock. It's not loud and I slept with it on last night crunching seti@H work.

The hdd don't vibrate the case at all and hum. The loudest thing I can hear right now is the fan on my 9800 pro 256 mb. That fan is noisy.

Oh well.

DOORS

The doors seat by sticking down into rail and then locking up top. Only one door has a lock adapter so the other door can be opened without monitoring. They are heavy and probably add much weight to the case.

WHEELS

I was previuosly using a SSTJ07 case. This was nice but was very dusty, heavy, and had no wheels. These wheels on this (lian-li) case are very nice. The rear wheels have a brake so basically you can activate the break and the case won't roll forward or backward. Remove brake and case rolls.

The case comes with tires for the wheels. These are rubber and slide over the metal wheels for protection.

EXTRAS

Lian-Li makes a see through door and also some different adapters for the power supply area if you want to run different stuff. Forget what buy it seems for redundant power supplies. Check their site for more info.

COLOR

This case comes in black and silver. I went for black because black is a much better neutral color for the eye to see compared to any other color. It doesn't blare out now because it's more stealth in appearance. I went for a red/black theme with some UV lights.

The UV lights can be mounted pretty much anywhere and there are options for mounting you will find when placing the lights for a test run.

SIZE

The case isn't that big as you will read. It is very very light. I was so surprised. I mean with the doors off it maybe weighs like 5-10 pounds. That's it. Yet is not noisy or rattling.

OTHER THOUGHTS

This case was fun to work with. I used a drill to attach all screws at the lowest torque setting. The power runs were long and you will want to consider a large power supply like the pcp+c 850/1kw if you are running multiple procs, dvd burners, overclocked, two sli/crossfire video cards because in total you could run a bunch of hardware.

The HDD cages are removable for what purpose I don't know. But this will reduce the structural ridgitiy of the case and I decided not to remove anything.

Bout it for now.

Lian Li cases are always impressive. Does the V2000 have a removeable motherboard tray, and if not, does it feel confined when you're working inside it?

It has no removable mobo tray. I don't feel confined. This case is giant and will support 9 inch long sata mobile racks because of the space in the 5.25 inch area.

The ONLY problem is with sata disks on the lowermost position in the stack. The sata cable kind of messes with the door getting on quickly. I'm sure if you zip tied the sata cables to an anchor this would be no prob. but considering sata cables are very easily unseated it is a prob.

Compared to the SS TJ07 I have the clearance for the door on this case is much better. Much better.

The SS TJ07 was stupid design because sata cables and molex power connectors hit the door like hit it literally.

The Lian-Li case took that into consideration and gives you a couple of inches for the cables to come off any disks before it meets the door.

SilverStone didn't' consider this it seems.

Other than that the case is big and I feel I could add a hampster wheel if I wanted to, except I don't like pets (too much work, plus what do they do if you work all day :( )

:laugh:

This topic is now closed to further replies.
  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Posts

    • Who is paying for this 30x scale-up? Its sounds expensive.
    • Millions of users to benefit from Windows 11's new performance boost on Adobe Photoshop by Sayan Sen Despite the advent of AI-generated imagery, Adobe's Photoshop remains one of the most popular tools on this planet. Adobe does not have a publicly reported total user count but it's probably not wrong to assume there are millions. As of 2025, Adobe Creative Cloud has had approximately 41 million paid subscribers, many of whom likely use Photoshop. In addition, more than 166,000 companies worldwide are apparently also using the app. These figures are according to a very recent report by SQ Magazine. Out of them, it is fair to assume that many are probably running Windows. As such, there is good news for these users as Microsoft has announced Photoshop is getting a big 20% performance boost on x86-64 (AMD64) systems and a 13% bump-up on Arm devices. This is definitely great news for them as many have complained about the slow performance and general sluggishness of Photoshop on Windows 11 ever since the advent of the latter back in 2021. If you are wondering how Microsoft managed to do this, the answer lies in a combination of compiler-level optimizations and a technology called Sample Profile Guided Optimization (SPGO). According to Microsoft, Adobe worked closely with the company’s Visual C++ team and adopted the latest MSVC toolchain enhancements together with SPGO to squeeze more performance out of Photoshop’s CPU-bound workloads. Unlike traditional Profile Guided Optimization (PGO), which requires developers to create special instrumented builds and run lengthy training workloads, SPGO gathers performance data directly from optimized release binaries. This means Adobe could collect real-world usage information which gives a major advantage to this technique, as companies could leverage data collected from actual customer workloads rather than only relying on synthetic benchmark runs. In theory, this should allow optimizations to better reflect how users interact with software in the real world. Thanks to this, there are improvements to code layout, function inlining, hot-and-cold code separation, and other low-level tweaks that help processors execute instructions more efficiently. Essentially the compiler is better able to identify “hot” code paths, those which are most frequently executed, and optimize them accordingly.
    • "The 2TB Samsung 990 PRO NVMe SSD hits lowest price in over three months¨ I'd prefer to see the lowest price in over a year
    • Glad these prices are starting to come down, but that is still crazy. I bought the 2TB 9100 Pro (slightly more expensive version with PCIe 5.0) last year for $240.
    • The 2TB Samsung 990 PRO NVMe SSD hits lowest price in over three months by Sayan Sen Yesterday, we covered a really good deal wherein you can get a 4TB TeamGroup T-FORCE G50 NVMe PCIe Gen4 SSD for a low price of just $400 with a special discount coupon. That's just $100 per TB, making it a very good offer during these hard times. The deal is still live, so you can check it out in its dedicated article here if you do not want to miss out. Meanwhile, if you don't have that kind of budget but still wish to buy an SSD for a good price, the 2TB variant of the TeamGroup SSD at $280 its lowest price in over three months. Meanwhile, those seeking 2TB but faster performance can check out Samsung's 990 PRO, which has hit the lowest price also in the last quarter or so, as it's on sale for $370 (purchase links under the specs table down below). Thus, you want a faster drive, get the 990 Pro, or you want more capacity, grab the TeamGroup 4TB linked in the first para. The 990 PRO is a PCIe Gen4 NVMe SSD and still one of the fastest drives available today for under $500. Speaking of fast, sequential reads and writes are rated at 7450 MB/s and 6900 MB/s, respectively. The random throughputs for reads and writes are 1400K IOPS and 1550K IOPS, respectively. The 990 PRO is based on Samsung's 7th Gen V-NAND flash, and it too is TLC. It packs 2 gigs of LPDDR4 DRAM cache, which helps the random performance. The endurance rating for this is 1200 TBW (terabytes written), which should be sufficient for most users. The Samsung 990 PRO is compatible with the PlayStation 5, but if you are going to use the 990 PRO on a PC, check out the Samsung Magician app that lets you track your drive's health, update its firmware, customize various settings, and more. The tech specs are given below: Specification TeamGroup T-FORCE G50 2TB Samsung 990 PRO 2TB Interface PCIe 4.0 x4, NVMe 1.4 PCIe Gen 4.0 x4, NVMe 2.0 Form Factor M.2 2280 M.2 2280 Controller InnoGrit Controller Samsung In-house Controller NAND Flash 3D TLC 3D TLC DRAM Cache None (HMB supported) 2GB LPDDR4 Sequential Read (Max) 5,000 MB/s 7,450 MB/s Sequential Write (Max) 4,500 MB/s 6,900 MB/s Random Read (4K) Up to 600,000 IOPS Up to 1,400,000 IOPS Random Write (4K) Up to 700,000 IOPS Up to 1,550,000 IOPS TBW (Endurance) 1,300 TBW 1,200 TBW MTBF 3,000,000 hours 1,500,000 hours Operating Temperature 0°C to 70°C 0°C to 70°C Storage Temperature -40°C to 85°C -40°C to 85°C Shock Resistance 1,500G / 0.5ms 1,500G / 0.5ms Heatsink Patented Graphene Heat Spreader No Get them at the links below: Samsung 990 PRO SSD 2TB (MZ-V9P2T0B/AM): $369.99 (Sold and Shipped by Amazon US) TEAMGROUP T-Force G50 2TB SSD (TM8FFE002T0C129): $279.99 (Sold by TeamGroup, Shipped by Amazon US) Good to know This Amazon deal is U.S. specific, and not available in other regions unless specified. We only use first-party seller links (at the time of article publishing); ensure that you purchase from a first-party seller link only. Check out Today's Deals on Amazon | or our recent tech deals. Become a Prime member (for Students or SNAP) via Neowin Get Prime Access - Prime for half price (for qualifying Medicaid, EBT, SNAP) Subscribe to Prime Video, Audible Plus, Music Unlimited or Kindle Unlimited via Neowin As an Amazon Associate, we earn from qualifying purchases.
  • Recent Achievements

    • First Post
      Jocimo earned a badge
      First Post
    • Week One Done
      suprememobiles48 earned a badge
      Week One Done
    • One Month Later
      Windows Guy earned a badge
      One Month Later
    • One Month Later
      Prasann earned a badge
      One Month Later
    • Week One Done
      Prasann earned a badge
      Week One Done
  • Popular Contributors

    1. 1
      +primortal
      522
    2. 2
      +Edouard
      174
    3. 3
      PsYcHoKiLLa
      90
    4. 4
      Steven P.
      81
    5. 5
      ATLien_0
      70
  • Tell a friend

    Love Neowin? Tell a friend!