Recommended Posts

Orion (aka Multi-Purpose Crew Vehicle) has had a slow, expensive gestation costing several $billion so far, and its first crewed mission won't happen until at least 2021.

How long? Its develioment stated the same year as SpaceX's Dragon.

http://www.nbcnews.com/science/space/nasa-puts-orion-spaceships-parachute-its-toughest-test-n141296
 

NASA Puts Orion Spaceship's Parachute to Its Toughest Test

NASA says the parachute designed for its Orion interplanetary spaceship passed its most complex test to date on Wednesday ? but an even bigger test is still to come.

At the start of Wednesday's run-through, a test version of the Orion craft was pulled out of a C-17 aircraft, 35,000 feet above the U.S Army's Yuma Proving Ground in Arizona. The craft went into a 10-second free fall, and then the parachute system was triggered to slow its descent. Engineers rigged the system with a built-in malfunction to see if it could tolerate failure. It could. The Orion test craft touched down safely in the desert, NASA reported.

The big test comes in December. That's when an uncrewed Orion spaceship will be launched atop a Delta 4 Heavy rocket, soar as far as 3,600 miles (5,800 kilometers) into space during a four-orbit journey, and then come screaming back to Earth at a speed of almost 20,000 mph (32,000 kilometers per hour).

The Orion's heat shield will have to weather temperatures near 4,000 degrees Fahrenheit (2,200 degrees Celsius). At the proper time, two drogue chutes and three main parachutes will have to pop out to slow down the Orion's fall to a manageable 20 mph for a Pacific Ocean splashdown.

That trial is called Exploration Flight Test 1, or EFT-1, and it's meant to blaze a trail for an uncrewed round-the-moon flight test that pairs Orion with NASA's heavy-lift Space Launch System in 2017. The first crewed Orion-SLS flight could come as early as 2021. NASA plans to use the spacecraft to send astronauts to a near-Earth asteroid, and then to Mars and its moons in the 2030s.

140625-orion2_7da710bc5f288ee25f8ad66198

Orion_Service_Module.jpg

Comparison (crew size)

Orion (4) v Apollo (3) v Dragon V2 (7 - 2 decks)
Z38.jpg
bp3jw2kieaakmfv-jpg-large.jpeg

I'd had a quick look but can anyone give the dimensions of the Dragon v2 for comparison?

The specs haven't been shared yet, but a lot of people have been using cues to calculate estimates. It uses the same pressure vessel as Dragon V1 with a minor change to the lower compartment housing the life support system. This makes things a bit easier, giving us minimums.

We know the mass of a fueled Dragon V1 was about 5.5 tonnes (empty) and that the Dragon V2 used for the DragonFly propulsive landing tests will mass about 7 tonnes.

The best estimates are that Dragon V2's heat shield diameter is 3.7 to 3.8 meters, with a height of about 6.3 meters to the top of the docking port (landing legs retracted.)

This is not counting the nose cone, which opens for docking then closes for reentry. Figure ~1 meter for that.

Of course Dragon V2 is much wider than the heat shield because of the 4 SuperDraco pods, and they aren't put at 90? intervals around its circumference. This pic should give.you an idea

anl0jlwxzlqyznte41mg.jpg.

Hey Doc, Have they done any launch abort tests yet? will Orion be up to spec?

They are a bit excited believing that SLS will be ready for 2017. I havent heard much news about it recently.

Pad abort test video at bottom. Orion's tower mounted abort solid is nearly the size of a theater ballistic missile. If unused all that mass is discarded.

Dragon V2's 8 SuperDraco abort thrusters are far smaller and lighter, each being about the size of a coffee can and a max of 16,400 lbf, and it keeps them as orbital maneuvering and landing engines. Powerful little SOB's.

Planned Orion missions

EFT-1: December 2014, Delta IV Heavy, high apogee loop, heat shield test.

EM-1: 2017-2018, SLS Block 1, circumlunar & return (unmanned)

EM-2: 2021-2022, SLS Block 1, crewed (2) visit of a retrieved asteroid in lunar orbit

EM-3: 2022++, SLS Block 1A. unknown

No firm plans or budget after these.

SpaceX may well be flying their Raptor engined, methane fueled, BFR super-heavy launcher before Orion/SLS flies its first crew.

With the pending December launch of an unmanned NASA Orion on a Delta IV Heavy to test the heat shield and systems, here's a rundown what needs to go right.

http://www.parabolicarc.com/2014/06/29/learn-orions-flight-test/#more-52722

WASHINGTON (NASA PR) ? All the superlatives associated with Orion?s first mission this year ? farthest a spacecraft for humans has gone in 40 years, largest heat shield, safest vehicle ever built ? can be dazzling, no doubt. But the reason engineers are chomping at the bit for Orion?s first mission is the promise of crucial flight test data that can be applied to the design for future missions. Orion only has two flight test opportunities before astronauts climb aboard for the first crewed mission in 2021 ? so gleaning the maximum information possible from Exploration Flight Test (EFT)-1 in December (and later, Exploration Mission-1 in 2017) is of the highest priority. Here are the top five things the engineers will be paying attention to:

1. Launch Abort System Separation ? The launch abort system (LAS) is a key reason that Orion is intended to become the safest spacecraft ever built. In an emergency it could activate to pull the crew module and the astronauts it will carry away from the launch pad and the rocket in milliseconds. Hopefully it?s never needed, and since no crew will fly on EFT-1 the rescue system won?t be active.

But even when a launch goes perfectly, the 904-pound LAS jettison motor has to perform flawlessly. If it doesn?t get rid of the LAS 6 minutes and 20 seconds into the mission, there will be no landing ? the LAS protects the crew module during ascent, but to do so, it blocks the parachutes that allow Orion to safely splashdown.

The Launch Abort System separation is just the first of 17 separations or jettisons that have to happen exactly as planned for the mission to be successful.

2. Parachute Deployment ? For EFT-1, Orion will travel 3,600 miles above the Earth so that when it performs its deorbit burn, it will come screaming back into the Earth?s atmosphere at almost 20,000 miles per hour. Before it splashes down in the Pacific Ocean, it needs to slow down to 1/1000th of its entry speed ? a relatively gentle 20 miles per hour.

Earth?s atmosphere does its part to put on the brakes, but to make landing survivable, Orion relies on its parachute system ? primarily two drogue parachutes and three massive mains that together would cover almost an entire football field. They?ve been tested on Earth; test versions of Orion have been dropped from airplanes with a multitude of failure scenarios programmed into the parachute deployment sequence in an effort to make sure that every possibly problem is accounted for.

But the sheer number of possible problems to be tested indicates how complicated the system is ? each parachute must deploy at the exact right time, open to the exact right percentages in the exact right stages, and be cut away exactly as planned. And no test on Earth can exactly simulate what the spacecraft will really experience on its return from space.

3. Heat Shield Protection ? Before the parachutes even get a chance to deploy, Orion has to make it safely through Earth?s atmosphere. The reason that Orion is traveling so far and coming back in so fast is to give the heat shield a good workout ? the idea is to get as close as possible to the temperatures Orion would experience during a return from Mars. At the speed it will be traveling, the temperature should reach almost 4,000 degrees Fahrenheit. At that same temperature, a nuclear reactor would melt down.

Standing between the crew module and all that heat is no more than 1.6 inches of Avcoat, a material that?s designed to burn away rather than transfer the temperatures back to Orion. Some 20 percent of the Avcoat will erode during the spacecraft?s journey back to Earth, and although it?s not the first time the materials has been used for this purpose, at 16.5 feet wide, Orion?s heat shield is the largest ever built. Technicians filled with Avcoat each of the 320,000 honeycomb cells that make up the shield?s structure by hand, then machined them to the precise fractions of inches called for by the design. Getting it exactly right is all that will get Orion through one of the most dynamic periods of its mission.

4. Radiation Levels ? Traveling 15 times farther into space than the International Space Station will take Orion beyond the radiation protection offered by Earth?s atmosphere and magnetic field. In fact, the majority of EFT-1 will take place inside the Van Allen Belts, clouds of heavy radiation that surround Earth. No spacecraft built for humans has passed through the Van Allen Belts since the Apollo missions, and even those only passed through the belts ? they didn?t linger.

Future crews don?t plan to spend more time than necessary inside the Van Allen Belts, either, but long missions to deep space will expose them to more radiation than astronauts have ever dealt with before. EFT-1?s extended stay in the Van Allen Belts offers a unique opportunity to see how Orion?s shielding will hold up to it. Sensors will record the peak radiation seen during the flight, as well as radiation levels throughout the flight, which can be mapped back to geographic hot spots.

5. Computer Function ? Orion?s computer is the first of its kind to be flown in space. It can process 480 million instructions per second. That?s 25 times faster than the International Space Station?s computers, 400 times faster than the space shuttle?s computers and 4,000 times faster than Apollo?s.

But to operate in space, it has to be able to handle extreme heat and cold, heavy radiation and the intense vibrations of launches, aborts and landings. And it has to operate through all of that without a single mistake. Just restarting the computer would take 15 seconds; and while that might sound lightning fast compared to your PC, you can cover a lot of ground in 15 seconds when you?re strapped to a rocket.

Check out all the tons stuff that gets tossed <7 min. after launch.

The conical cover attached to the launch escape systems "tractor" rocket prevents it from melting the Orion, and cooking the crew inside.

The commercial spacecraft have done away with with the tractor LES, using smaller rockets at the sides or bottom of the spacecraft in a "pusher" arrangement. This saves several tons of launch mass and several jettison events. It also retires the issue of the LES blocking parachute deployment if it fails to separate.

Picture11.png

  • 4 months later...

 

Hey Doc,

 

Any update on this bad boy.

 

Are they still going to meet the December time frame?

 

 

 

 

From NASA

"NASA?s new Orion spacecraft received finishing touches Thursday, marking the conclusion of construction on the first spacecraft designed to send humans into deep space beyond the moon, including a journey to Mars that begins with its first test flight Dec. 4."

https://blogs.nasa.gov/orion/2014/10/30/nasas-orion-spacecraft-complete/

On track for Dec. 4, but be aware EFT-1 isn't a full-up Orion. Its a stripped down test article with just enough gear on it to do this flight. Guidance, thrusters, heat shield, parachutes etc.

A "real" Orion won't fly until at least 2018, and that'll also be unmanned. That date is paced by the SLS launcher and it's behind schedule. No crews until 2021 to 2022, and that'll be a rehash of Apollo 8's loop around the Moon.

Assuming the SLS program isn't cancelled by then, which is quite possible.

October 8, 2014

NASA Premieres ?Trial By Fire? Video on Orion?s Flight Test

As the flight test of NASA?s Orion spacecraft nears, the agency released Wednesday a video -- called "Trial By Fire" -- detailing the spacecraft?s test and the critical systems engineers will evaluate during the Dec. 4 flight.

Orion is in the final stages of preparation for the uncrewed flight test that will take it 3,600 miles above Earth on a 4.5-hour mission to test many of the systems necessary for future human missions into deep space. After two orbits, Orion will reenter Earth?s atmosphere at almost 20,000 miles per hour, and reach temperatures near 4,000 degrees Fahrenheit before its parachute system deploys to slow the spacecraft for a splashdown in the Pacific Ocean.

On future missions, Orion will carry astronauts farther into the solar system than ever before, including to an asteroid and Mars.

View the Trial By Fire video at:

http://bit.ly/1pMQUkx

For more information about Orion and its first space flight, visit:

http://www.nasa.gov/orion

Orion: Trial By Fire:

http://youtu.be/KyZqSWWKmHQ

  • 4 weeks later...

Orion Exploration Flight Test-1 (EFT-1)

Launcher: Delta IV Heavy (SLS is still years off)

Mission: similar to the 1967 Apollo 4 mission, an Orion instrumented test article (incomplete systems) will go into low Earth orbit then loop out to an altitude of 3,600 miles (5,800 km) and do a high speed re-entry at 20,000 mph (32,000 kph). This will test its heat shield at a temperature of 4,000 ?F (2,200 ?C), 80% of what it would experience returning from the Moon.

Launch location: Cape Canaveral LC-37B

Launch Date: December 4, 2014

Launch Window: 0705-0944 Local (Eastern)

NASA TV: 0430 Local (ET)

Orion Teams on Track

https://blogs.nasa.gov/orion/

Flight Readiness Review passed

https://blogs.nasa.gov/orion/2014/11/25/launch-and-mission-operations-teams-run-through-mission-practice/

news-111214b-lg.jpg

1280px-Rendering_of_Orion_Exploration_Fl

EFT-1_mission_diagram.jpg

It's possible. Unlikely.

Lots of things can go wrong at cryogenic temps, and liquid hydrogen boils at ?252.87?C (?423.17?F). Could be some moisture got in the system and froze, dissimilar contraction or whatever. I'm betting on moisture.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Posts

    • These are not "great" prices... just "less awful". Apparently "Those who forget the past are doomed to pay higher prices and think they've won."
    • Russia was able to invade Crimea because of those people. But my point is that I've personally heard how great it was to be "back in Russia" right afterwards - look how great it is now. I've asked you a question in another comment which you haven't answered, so I'll ask it again: is it better now without "Europrats"?
    • ZimaBoard 2 1664 Starter Kit review: it's a cool and affordable DIY NAS by Steven Parker IceWhale Technology reached out to me asking if I was interested in testing the ZimaBoard 2, and after convincing them to send me the Starter Kit, it arrived at my doorstep in May. A bit of background: it is a Shanghai-based Chinese company founded in 2020, which specializes in single-board servers and personal cloud solutions. From searching around online, user feedback on the company and ZimaOS is mostly positive, so we're off to a good start. In addition, I should probably point out that although they do not have a large portfolio of NAS devices, with just four of what they do offer, they seem to have covered everything from a relatively low-priced entry point with the ZimaBoard 2, right up to the high end, with the ZimaCube 2 Creator Pack that even includes an NVIDIA RTX PRO 2000. Anyway, as already mentioned, what we have today is the ZimaBoard 2 Starter Kit, and here are the full specifications: ZimaBoard 2 Model 832, 1664 CPU Intel Core N150 (4x E Cores/Threads, Max burst up to 3.6 GHz) TDP: 6W (Base) 10W (Max) Graphics Intel UHD Graphics 24 EUs (1.00 GHz) Memory 8 GB, 16 GB DDR5 4800MT/s non ECC SODIMM (soldered) Disk Capacity 60 TB (30 TB x 2) Supported RAID Types TRAID, TRAID +, RAID0, RAID1, RAID5, RAID 6, RAID 10 Storage 2 x SATA 3.0 6Gb/s Ports with Power Bootloader 32 GB, 64 GB eMMC Network 2x RJ-45 2.5 GbE PCIe 1 x PCIe 3.0 (via LPC) USB Ports 2 x USB-A 3.1 (5 Gbps) Display Mini-DisplayPort 1.4 (4K@60Hz) Hardware Transcoding Engine H.264, H.265, MPEG-4, VC-1 Maximum resolution: 4K (4096 x 2160); Maximum FPS: 60 Virtualization Intel® AES New Instructions Intel® Virtualization Technology (VT-x) Intel® Virtualization Technology for Directed I/O (VT-d) Size (H/W/D) 140mm x 83mm x 31mm Weight 0.4 kg (only ZimaBoard 2 device) Power 12v 5A Power Supply Warranty 1 year (Global) 2 Years (EU) OS ZimaOS v1.6.1 MSRP $339, $399 ($548.60) As you can see above, there are two variants of the ZimaBoard 2. The lesser variant has half the eMMC storage and 8 GB less RAM, although it also costs $60 less than the top variant we are testing today. The above pricing is only for the ZimaBoard 2. I put the MSRP of the Starter Kit next to it in brackets, although as of publishing, it is discounted to $534.50. The ZimaBoard 2 started life on Kickstarter and shipped to backers in August last year. It became available via the official website in late 2025 and Q1 2026. This hobbyist NAS contains the still relatively new N150 Intel CPU released in the first quarter of 2025, with support for DisplayPort 1.4, HDMI 2.1, although in this case, the memory is integrated into the board itself, so it will not be possible to upgrade or expand the amount. It also supports AV1 decoding, as well as H.264, VP8, VP9, H.265 (8 bit), and H.265 (10 bit). The different capabilities in the Alder Lake-N (and Twin Lake) series are listed below. Processor E-cores L3-cache Turbo clock GPU GPU-clock TDP Intel N355 8 6 MB 3.9 GHz 32 EUs 1.35 GHz 9 W Intel Core 3 N350 3.9 GHz 1.35 GHz 7 W Intel Core i3-N305 3.8 GHz 1.25 GHz 9 W Intel Core i3-N300 3.8 GHz 1.25 GHz Intel N250 4 3.8 GHz 1.25 GHz 6 W Intel Processor N200 3.7 GHz 0.75 GHz Intel N150 3.6 GHz 24 EUs 1 GHz Intel N97 1.2 GHz 12 W Intel Processor N100 3.4 GHz 0.75 GHz 6 W The CPU is part of the Twin Lake series that sits near the bottom of the N-series, designed for low- powered systems and entry-level laptops, and as such has a base level TDP of just 6W. As I have noted before, we are seeing another NAS with a great amount of RAM. It's important to mention that the ZimaBoard 2's memory is integrated into the base board (which is why they have two variants of it). As a reminder, up until a couple of years ago, it was commonplace to only get 2 or 4GB max on a flagship Synology or QNAP home NAS. Ever since the likes of TerraMaster and more have entered the market with ample RAM sizes included in their NAS offerings, it has gone a long way in forcing the hands of the traditional makers to up their game a bit. First impressions The Starter Kit came in one outer box with several packages inside it (shown above). I forgot to take pics of it because when it arrived, it wasn't clear what was inside, and I had to confirm with my contact that I received the entire Starter Kit. In the box ZimaBoard 2 ZimaBoard 2 HDD Expansion Bracket + PCIe card frame Zimaboard Mini DisplayPort Male to HDMI Female Cable 4K 60Hz Zimaboard PCIe 3.0 x4 to Dual NVMe M.2 SSD Adapter Card Quick guide [full online guide] Limited warranty notice Screws Design Where to start? You'd be forgiven for mistaking it as an SSD enclosure if not for all the ports on it. It is completely made out of metal, and the top is an entire heatsink. It has a premium feel about it, but it definitely looks like a hobby device. As you will see, the completed build looks like it belongs in a server or meter closet rather than as a showpiece on someone's desk. On what I am calling the rear, there's a Mini DisplayPort (1.4), two 2.5 GbE ports, with Type A 3.1 USB ports, and then the barrel connector port. Around the front, there are two SATA6 ports with a power connector in the middle. Left side Right side One side is completely free of ports. On the other there's a slit that allows for the feed of a CPU fan cable, and a PCIe 3.0 X4 slot. Top Bottom The top is entirely made up of a heatsink except for the extended height for the I/O on the rear. Around the other side, you can find the ZIMA branding and some regulatory information stamped near the bottom. As you may see from the bottom of the ZimaBoard 2, it scratches quite easily from just moving it around on my Ikea island. Teardown Before we get started, let's have a look at this thing on the inside. The steps to get to the board are as follows: Remove the four smaller Torx screws on the bottom of the ZimaBoard 2; Remove the four larger Torx screws on the sides of the device; Carefully unstick the CMOS battery from the PCB; Remove two Phillips screws on the PCB; Lift out the PCB. Yes, as you can tell from the instructions, you need three different tools to remove Torx and Phillips screws (10 in total), and unhelpfully, one of the screws is located under the CMOS battery, which is stuck onto the PCB. Building Now comes the fun part. Because the ZimaSpace website does not provide any guidance on how to put the Starter Kit together. They only have guidance for connecting the CPU fan. However, they did upload a video to their YouTube channel that shows the entire process. To install the fan, first remove the four screws on the bottom of the ZimaBoard 2, then on the inside, there is a CPU FAN connector where you can attach the fan, reattach the ZimaBoard 2 frame, and feed the fan cable through the provided slit. Then remove the nearest screw on the side and attach the fan frame to the side of the device using the same screw. ZimaBard 2 screws Aligning the screws Bottom view Remember those four screws we removed to access the CPU FAN? Longer screws are provided in the box with the HDD Expansion Bracket, which is what you will now need to attach the ZimaBoard 2 to it. Helpfully, the orientation on how to attach it is made obvious when the frame can only be screwed on at the same overall length as the ZimaBoard 2. If you do it the wrong way around (which is what I did initially) one side hangs off the frame, and it becomes difficult to attach the PCIe Adapter Card cable. PCIe card frame Other side PCIe slot connector Next, it's time to attach the PCIe card frame, which is fastened with the help of 3.5-inch SATA HDD (3 screws). These are toolless screws that you can just use your fingers to fasten them with. Then it is time to connect the provided PCIe cable with the slot connector on one side of the ZimaBoard 2, feed it through the bottom of the HDD frame, and fasten it with two standoffs. Both bracket options 2280 standoffs with 2x 4TB MP44Q The PCIe 3.0 X4 card comes with a short bracket option, handy if you decide to place it inside a different NAS or rack server, but here we need the long bracket. Oddly enough, the M.2 standoffs were preinstalled into the 22110 position, but extra standoffs are included in the box, which I installed at the 2280 position for our use. I added a couple of MP44Q M.2 PCIe 4.0 SSDs (2 x 4TB) that can be availed on Amazon for $478.99 (the lowest price for 3 months) that TEAMGROUP supplied us with Then we have the almost completed build, you just need to push the card into the PCIe slot. Unfortunately, IceWhale Technologies did not provide a screw for the PCIe card frame (this is also apparent in their own video). Here it is at several different angles, with the last pic showing the SATA Y-Cable connected to the two WD Red Plus 4TB drives. Setup and Usage Next, you connect your cables to the I/O, and the ZimaBoard 2 powers on automatically, as there is no power button on the device. Power is controlled through the Settings in ZimaOS. BIOS The ZimaBoard 2 includes an Aptio BIOS from American Megatrends [1, 2, 3], and you can setup pretty much everything here including the boot order, which is locked to the UEFI OS, however above that choice you can enable or disable booting to a SATA/USB bootloader so this would still allow you to switch to an alternative bootloader and boot from it, or disable it to instead always start from the first disk with an OS installed on it. Initial Setup Upon connecting to the LAN and booting up, the ZimaBoard 2 can be reached by navigating to the IP address (shown if you have a monitor connected), or you can find it using the ZIMA Client desktop application, which is essentially a Zima device finder. Initializing the ZimaBoard 2 The ZimaOS setup process is pretty straightforward, through a wizard, and in full above, it basically consists of setting up an account and some handy tips, and that's that! Post Setup (ZimaOS update) Upon first boot, you are alerted that there is a ZimaOS update from 1.5.0 to 1.6.1, which I applied; the full process is shown above with the changelog. ZimaBoard 2 Storage Setup Next, it is time to set up the storage. ZimaOS actually throws everything onto the eMMC flash drive; it is also the default location of AppData, which is definitely something to be wary about, as the 45GB available storage could fill up quickly. HDDs I first attempted to create a Storage Pool using the two 4TB WD Red Plus NAS drives, and got an error message: After several attempts and then looking online, I discovered it was a bug with ZimaOS where the fix was simply to reboot ZimaOS and then try again, this time I was able to create a RAID mirror using the two drives. SSDs I did the same for the SSDs, as you will see in the above gallery, when I created the second Storage Pool, it only allowed me to select available drives. ZimaBoard 2 AppData ZimaOS comes with an App Store that includes a repository of almost 400 apps, so you will be able to find most of what you'll need for a NAS (although after a quick search, I wasn't able to find a Surveillance Manager), and now comes the important part: moving the default AppData location off the 45GB eMMC and onto a larger volume: Open Settings Then Apps Then, in the Select a new location field, click on the new Storage volume you want to move it to (in my case, the Apps Storage Pool), which is the SSD RAID mirror. Confirm the Migration warning Be praised! You can also do this for Docker (which by default installs onto the 45GB eMMC flash drive) and the User database. Plex Setup Next, I tested the configuration by installing the Plex Server app from the App Store. The library folders must already exist (which I placed into the Storage Pool). Plex Server setup is straightforward and requires very little configuration. In my case, all I had to do was add the media path I just created, which you can also browse to using the folder icon in the path field. In addition, you can now map the new Media library in Windows Explorer using the Zima Client. Oddly enough, it is not possible to access the ZimaBoard 2 over the Network Neighborhood; you must map drives using the client, which is shown in the last image in the above gallery. I watched one of my Blu-Ray rips, which is Dolby Vision with Dolby Atmos, and the content played fine with no stuttering or buffering, which is what anyone needs in this scenario. ZimaBoard 2 Zima Client mobile app There's also a client for mobile. It is pretty barebones, as shown in the above gallery, for example, the Apps screen launches the WebUI for that app, and the Backup must be done manually. On opening Backup, you can select internal storage folders on your phone to backup to the ZimaBoard 2's storage, and although this is constantly scanned, the backup action itself must be manually triggered. There is an option to allow foreground backup (last image in the above gallery), but this basically means the queued backup gets triggered when you manually open the app. Benchmarking SATA PCIe 3.0 X4 A CrystalDiskMark test on a mapped network drive from within a Windows 11 25H2 PC (image above) connected over a 2.5 GbE was well within acceptable ranges. Writes were generally better on the SSD RAID mirror. SATA PCIe 3.0 X1 I also ran the NAS Performance tester, which tests the link speed performance. As you can see, it pretty much maxes out the 2.5GbE connection. Of course, you can also opt to bond the two 2.5 GbE connections for a bit more umph, but I didn't do that. Thermals Top PCIe card SATA HDDs Next, I measured some hotspots while playing content on Plex. It's fair to say this will perform better than a NAS that is enclosed in a metal or plastic case, as almost everything storage-wise is exposed! Anyway, the ZimaBoard 2 did not break a sweat with Plex streaming or disk benchmarks. ZimaOS Factory Reset ZimaOS does not include a factory reset option. Instead, you have to download the ZimaOS image and flash it to the eMMC manually. The flashing process is shown in the above gallery. The steps to do so are listed below: Download the ZimaOS image here; Open BalenaEtcher (Run as Administrator) and select the image; Select your inserted USB drive (min 8 GB) Flash to it; Connect your USB drive, monitor, keyboard, USB hub (optional), mouse (optional), and network cable (recommended) to the ZimaBoard 2; Connect power and press F11 continuously; Select your USB drive starting with UEFI in the boot device menu; Press Enter on the Install ZimaOS option; Select /dev/mmcblk0 (MMC) flash drive as target; Confirm with (three times) to wipe the target disk; Wait a couple of minutes while ZimaOS installs; Remove the USB drive and confirm with a reboot; Your ZimaBoard 2 has been factory reset. However, you don't have to stick with ZimaOS, in fact the company also offers official CasaOS images, that are based on Debian; or as they say themselves, put anything you want on this "hackable single board server" it's up to you. Conclusion I had a lot of fun putting this together. I've custom-built all my own PCs and servers since the 90s, and this is the first time I have had to put a NAS together. Even if the actual base ZimaBoard 2 was already a completed build, it still feels pretty custom. I just wish that IceWhale Technology included a getting-started guide in the box for the Start Kit, which would have really completed this kit. Instead, I had to search for the official video on the YouTube channel to make sure I wasn't doing anything wrong. So who is this for? Definitely the hobbyist who is comfortable building their own PC and servers. It also has a much smaller footprint than its nearest equivalent (in terms of specs), like the Beelink Me Pro, which is another NAS I will be testing soon. Although the Beelink does not come with the PCIe 3.0 X4 expansion, the ZimaBoard 2 Starter Kit suddenly looks to be a great bargain, even if it only offers the two 3.5-inch bays over the four in the other example. It makes a lot of sense to use Intel's N150 chip inside a NAS; it is more than capable of doing what the ZimaBoard 2 is intended for, media streaming and backup. It also looks like the IceWhale Technology staff are quite active in the official forums helping people with issues they come across with ZimaOS and the devices, peer support seems to be good as well, I was quickly able to find why I was not able to create a new Storage Pool in ZimaOS v1.6.1 even though that is quite a serious bug, hopefully it will be fixed in the next update. If you are comfortable with the command line and Docker, you'll be fine. You can do great things with this hardware. This was my first time with ZimaOS. It seems a bit barebones in comparison to the likes of Synology DSM, TOS, and UGOS, but it has a ton of apps to get you started with your home or small business NAS. Where to buy As of publishing, IceWhale Technology is running a discount of up to 5% for the Starter Kit. If you opt to get just the ZimaBoard 2 itself, it does come with a SATA Y-Cable, so you will be able to connect up to two 3.5-inch HDDs to it. ZimaBoard 2 1668 Starter Kit for $534.50 on Amazon US (was $548.60) ZimaBoard 2 832 Starter Kit for $372.88 on Amazon US (was $390.60) Zimaboard 2 1668 (16GB+64GB) for $419.90 on Amazon US Zimaboard 2 832 (8GB+32GB) for $359.90 on Amazon Disclosure: IceWhale Technology provided a free sample without any editorial input or review pre-approval. Good to know The Amazon link is U.S. specific, and not available in other regions unless specified. We only use first-party seller links (at the time of article publishing); ensure that you purchase from a first-party seller link only. Check out Today's Deals on Amazon | or our recent tech deals. Become a Prime member (for Students or SNAP) via Neowin Get Prime Access - Prime for half price (for qualifying Medicaid, EBT, SNAP) Subscribe to Prime Video, Audible Plus, Music Unlimited or Kindle Unlimited via Neowin As an Amazon Associate, when you purchase through links on our site, we earn from qualifying purchases.
    • It's in the Insider's group so yes it's technically beta, though these days it's hard to see much of a difference unless you opt for the most extreme beta builds, which I don't. When I moved here from the Release Preview channel I did so primarily because I wanted to see how well the restored taskbar functionality (restored from Win10, and earlier) is working and whether it was time to finally abandon SAB--and it is--working fine, so far. Not as polished as SAB, but it'll do for me.
    • I've been using MWB Premium for a number of years so that along with Windows updates and updated browser should be fine. Thanks for that.
  • Recent Achievements

    • Week One Done
      flexorcist earned a badge
      Week One Done
    • One Month Later
      Woland13 earned a badge
      One Month Later
    • Week One Done
      Woland13 earned a badge
      Week One Done
    • One Year In
      bernmeister earned a badge
      One Year In
    • Week One Done
      Scoobystu earned a badge
      Week One Done
  • Popular Contributors

    1. 1
      +primortal
      488
    2. 2
      +Edouard
      220
    3. 3
      PsYcHoKiLLa
      147
    4. 4
      Steven P.
      74
    5. 5
      FloatingFatMan
      70
  • Tell a friend

    Love Neowin? Tell a friend!