Recommended Posts

It's always nice to see a Delta Heavy fly, but otherwise... Orion, SLS. I just cant stop thinking about the lost opportunity cost. And for what? And to where? For no reason -except $$$$$ spent -and nowhere worth going to at that cost, and maybe not at all.

Economies and budgets in decline everywhere, resources squandered, time wasted...

  • Like 1

SpaceX has a manifest whose value is approaching $6B, and of that $1.6B is NASA for Cargo Resupply Services.

Commercial Crew launch contracts won't be added for 2 more years, and any use of NASA facilities not a part ofCommercial Cargo or Crew is on SpaceX's dime. This includes their cargo fairing, Falcon 9 v1.1, Falcon Heavy and the F9R reusability developments.

SpaceX also paid to upgrade a stand at NASA Stennis for testing the Raptor Mars engine, and it's components have been tested since late May. That train is leaving the station a lot sooner than most people think, and certainly sooner than 2030.

The biggest issue with SLS I find is that, the senate is hellbent on giving back the Michoud facilities and anyone else who lost their job at the Space Shuttle's retirement their job back, which is nice... But... The SSMEs are shall we say this, old, like pre 1980's old. The SRBs I happen to have a bit of beef with using Solid fuel, as opposed to using liquid fueled engines which can be shut down in case of an emergency. Docm please chime in if I am straying off topic too much. But for pete's sake, SLS is tax payer dollars going to waste imh. You figure, they are going to wait till 2018 to shoot Serial # 1 of SLS because of NASAs laughable budget... Like Docm and previous poster quipped, Spacex will be running a taxi service to the moon before 2018.

The old Shuttle SSME's (RS-25) will only be used on the first few SLS flights, IIRC they only have 12, then they need a new engine which hasn't been chosen yet. They could re-start the RS-25 line and produce new expendable versions, or use another engine. Either will be very expensive.

Then there is the SLS upper stage kettle of worms.

NASA spent $billions upgrading Saturn V's J-2 upper stage engine to the J-2X then shelved it. Sound familiar? Now they're using 4 RL10C-1's, whose heritage dates to 1962, in a totally new Exploration Upper Stage. This while simultaneously searching for an RL10 replacement in the EELV Centaur upper stages.

/sigh....

With SpaceX's fracking bloody huge Raptor engine components already on a test stand at NASA Stennis it's not too big a reach that their BFR launcher will fly years before the upgraded (non RS-25) SLS does.

BFR makes SLS look small, with very good reasons to believe it'll be a 12.5 to 15 meter wide core vs. SLS's 8.4 meters. They'll need those big tanks to feed 9(!) Raptors and still keep the BFR under 400 feet tall.

NASA should save some major bucks and use BFR, but the Lockheed/Boeing lobby has too much influence in the Senate regardless of what party's in control.

  • Like 1

So essentially Docm, the SLS is doa... These guys hoarded 12 motors for the first few flights, and then... oh wait, there are no more engines...  Also, if I may ask isn't the RL10 also part of the DELTA IV Upper stage?

 

Also, 12 motors, which means if they pin 4 of these things, they are looking at 3 flights until its game over, 5 like the ARES V design and well. its going to be a shorter ride until they run out of SSMEs

The RL10 is used in both the Atlas V Centaur upper stage (1 or 2 engines) and the Delta IV DCSS (Delta Cryogenic Second Stage).

Atlas V may be scrapped because of the Russian engine deal. ULA and Blue Origin are working on a methane fueled EELV using the latters BE-4 in the first stage and the smaller BE-3 in the second stage.

It would have more first stage thrust and a better first stage Isp than Atlas V, which could eliminate solid boosters for most launches.

Hey Docm, what would SpaceX have to do to to Human rate the Falcon 9 v 1.1.?

Falcon 9 v1.1/F9R was designed as a human rated launcher, so physically it already is. The main difference would be a software upload to reduce G loads the crew is exposed to and avoid maneuvers that would make aborts difficult (aka "black zones".)

It actually goes goes beyond the usual human ratings because it has engine-out capability. Engine-out for Falcon 9 v1.1 means there is armor plate and fireproofing between its 9 engines, so if one or two fail catastrophically the others are protected and can simply throttle up to continue the mission.

Having the 9 engine layout means losing one only reduces thrust by 11% instead of 50% like Antares. Such a single engine failure with Falcon 9 wouldn't end the mission

This has actually been used during a CRS flight of Falcon 9 v1.0, which also had engine-out. The fuel dome of its #5 engine let go so the computers shut its systems off, burned the remaining 8 engines longer to compensate (it's engines weren't throttleable), and Dragon got to ISS 30 minutes early.

Most likely January given all the effort and the delay caused by getting Dragon CRS-5 reconfigured to haul up duplicates of critical cargo lost in the Antares explosion.

The pad abort test involves a temporary platform attachment for LC-40's TEL (transporter erector launcher) that'll raise Dragon 2 to its launch height. It also provides the operational data lines and stage 2 mechanical and fluid attachments. It's been mounted to the TEL and tested, so after CRS-5 they'll re-mount it and prep for the pad abort.

It's also VERY likely Falcon 9 will launch 2 Cygnus CRS missions while Orbital qualifies different engines for Antares. Most likely the RD-193, a derivation of the RD-191 used in Angara. It's a drop-replacement for Antares NK-33.

Most likely January given all the effort and the delay caused by getting Dragon CRS-5 reconfigured to haul up duplicates of critical cargo lost in the Antares explosion.

The pad abort test involves a temporary platform attachment for LC-40's TEL (transporter erector launcher) that'll raise Dragon 2 to its launch height. It also provides the operational data lines and stage 2 mechanical and fluid attachments. It's been mounted to the TEL and tested, so after CRS-5 they'll re-mount it and prep for the pad abort.

It's also VERY likely Falcon 9 will launch 2 Cygnus CRS missions while Orbital qualifies different engines for Antares. Most likely the RD-193, a derivation of the RD-191 used in Angara. It's a drop-replacement for Antares NK-33.

Will they fly the Cygnus capsule up or will they just use a Dragon capsule since it's already fitted to go on a Falcon 9?

They'll fly an improved Cygnus spacecraft. The Cygnus uses interfaces that are very similar to other Orbital built satellites F9 has launched and the companies have worked well together.

The improvement consists of adding container segments which make it longer, and also making it possible to use Cygnus as a crew mission habitat for Orion, Dragon 2 or CST-100 during long duration flights.

For Dragon 2 the theory is a Cygnus could be mounted to the F9 upper stage but inside a Dragon 2 stretched Trunk. Dragon and the Trunk would separate, turn around, dock with and move away with the Cygnus much as Apollo did with the LEM.

Cygnus-Congigurations.jpg

cst100_cygnus_bkgtest2.jpg

Thanks you guys, for clearing that out. So I take it the next step for SPACEX would be to go through the battery of tests to certify DRAGON 2.0 as human rated, are there any timelines for said work to commence?

Pad abort around January 2015 as discussed, an in-flight abort test spring/summer 2015 at Vandenberg, and a full up orbital test in early/mid 2016. SpaceX believes a crewed test could happen later in 2016, but NASA may not have the funding.

SpaceX may fly a crew in 2016 on their own dime to put an exclamation point on things since CST-100 won't be ready until 2017.

  • 1 month later...

NASA announces that the RS-25 (aka: Space Shuttle Main engines) will be the permanent first stage propulsion, with AEROJET restarting the production of said motors, the motors are modified for SENATE LAUNCH SYSTEM, ehem, I mean Space launch system, and thus now called RS-25D

 

 

http://news.yahoo.com/nasa-conducts-1st-test-fire-shuttle-era-engine-123208742.html

  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Posts

    • Onkyo Dolby Atmos AV receivers are really solid deals by Sayan Sen Recently we covered great deals on several soundbar models from the likes of Sony, JBL, Samsung and others for really good prices (the lowest in several months). Aside from that we also reported on the Edifier S3000MKII, a hi-fi two-way bookshelf monitor that's available for only $800. Today we bring a list of AV receivers from Onkyo that are available at great prices including the Onkyo NR7100, RZ30, and 8470 (purchase links under the specs table down below). The Onkyo TX-NR7100 and Onkyo TX-RZ30 are both 9.2-channel AV receivers designed for immersive home theater setups but they occupy slightly different tiers within Onkyo’s lineup with the RZ30 positioned as the more advanced model. The TX-NR7100 is a THX Certified 9.2-channel receiver offering up to 100 W per channel (8 ohms, 2 channels driven). It supports Dolby Atmos, DTS:X, and IMAX Enhanced formats, with flexible configurations such as 5.1.4 or 7.1.2 speaker layouts. A key highlight is its built-in Dirac Live Room Correction which should help optimize sound based on your room and its acoustics. In comparison, both models share several core capabilities though the RZ30 is geared toward enthusiasts seeking more precise calibration and system flexibility, while the NR7100 is positioned as a slightly more accessible, value-focused option with strong all-round performance. The technical specs of the RZ30 and NR7100 9.2 AVRs are given in the table below: Specification Onkyo TX-RZ30 Onkyo TX-NR7100 Power Output (FTC, 2ch driven) ~100 W/ch (8Ω, 20Hz–20kHz, 0.08% THD) 100 W/ch (8Ω, 20Hz–20kHz, 0.08% THD) Dynamic / Peak Power 9 × 170 W (6Ω, 1kHz, 1% THD, 1ch driven) 220 W/ch (6Ω, 1kHz, 10% THD, 1ch driven) Frequency Response 5 Hz – 100 kHz (+1/-3 dB) 10 Hz – 100 kHz (+1/-3 dB) THD 0.08% 0.08% Room Correction Dirac Live (full bandwidth) Dirac Live (with AccuReflex support) Immersive Audio Dolby Atmos, DTS:X, IMAX Enhanced Dolby Atmos, DTS:X, IMAX Enhanced Speaker Layout Support Up to 7.2.2 / 5.2.4 / 9.2 processing Up to 7.2.4 / 5.2.4 / 9.2 processing HDMI Inputs / Outputs 6 inputs / 2 outputs (eARC) 6 inputs / 2 outputs (Main + Sub/Zone 2) HDMI 2.1 Support 8K/60, 4K/120, VRR, ALLM, QFT, DSC, eARC 8K/60, 4K/120, VRR, ALLM, QFT, DSC, eARC Video Formats HDR10+, Dolby Vision, HDCP 2.3 HDR10+, Dolby Vision, HDCP 2.3 Streaming / Network Wi-Fi, AirPlay 2, Chromecast, Bluetooth, DTS Play-Fi Wi-Fi, AirPlay 2, Chromecast, Bluetooth, DTS Play-Fi Get them at the links below: Onkyo TX-RZ30 9.2-Channel AV Receiver: $797.00 (Sold and shipped by Electronic Expo) Onkyo TX-NR7100 9.2-Channel AV Receiver: $699.00 (Sold and shipped by Adorma) Onkyo TX-8470 2 Ch Stereo Receiver: $449.00 (Sold and Shipped by Adorma) Good to know This Amazon deal is U.S. specific, and not available in other regions unless specified. We only use first-party seller links or authorized dealer links (at the time of article publishing); ensure that you purchase from such links only. Check out Today's Deals on Amazon | or our recent tech deals. Become a Prime member (for Students or SNAP) via Neowin Get Prime Access - Prime for half price (for qualifying Medicaid, EBT, SNAP) Subscribe to Prime Video, Audible Plus, Music Unlimited or Kindle Unlimited via Neowin As an Amazon Associate, we earn from qualifying purchases.
    • A different thing with Russia. When you say is it better, depends on things. It is better that we don't have the E.U making rules and laws that have nothing to do with them. Is the trading part better? No, that is really mucked up, but then we knew that was going to happen and we would have make agreements, like we do with other parts of the world. Freedom of movement is certainly better, but could be improved, we still need more control over our borders. do you live in the U.K?
    • So what am I quoting from them? I never listened to what Farage or his cronies said. I wanted the U.K to leave the E.u years before the referendum and it had nothing to do with Farage and his cronies. So what country do you live in? Did we work much better together? We were always at logger heads with the E.U because we disagreed with them so much. Maggie was always on at them. I would have thought the E.U was glad to get rid of us as we stopped the integration or made it a two tier. Now without us they can integrate more. I would not have voted out if it was just a trading block and we can still work together on somethings.
    • MPC-BE 1.9.0 by Razvan Serea Media Player Classic - BE is a free and open source audio and video player for Windows. Media Player Classic - BE is based on the original "Media Player Classic" project (Gabest) and "Media Player Classic Home Cinema" project (Casimir666), contains additional features and bug fixes. The BE mod (Black Edition Mod) is a skinned version of Media Player Classic Home Cinema, much better looking than the plain old MPC. MPC-BE 1.9.0 changelog: Splitters Fixed crashes in some situations. AudioSplitter Added support for the RF64 format. Fixed reading of channel layout for some WavPack files. Added support for ID3 tags for Wave64 files. Unknown Wave64 chunks are now ignored. AviSplitter Added support for 'y408' video. Improved support for 'HEVC' video. FLVSplitter Added support for VVC video. MP4Splitter Improved handling of corrupted files. MatroskaSplitter Expanded support for V_UNCOMPRESSED video codecs. Fixed support for frame rotation (ProjectionPoseRoll). Improved support for "V_MS/VFW/FOURCC / HEVC". MpcDvdVideoDecoder Fixed conversion to YUY2. Fixed display of menus for some DVD-Videos. RoQVideoDecoder Output in NV12 and YV12 formats is allowed. Full range is used. MPC Video Decoder RGB32 format will be output as a top-down bitmap by default. Added support for the "IID_MediaSideDataDOVIMetadataV2" interface. Removed support for the deprecated "IID_MediaSideDataDOVIMetadata" interface. Fixed retrieving the name of the video adapter when using NVDEC. Fixed crashes in some situations. MPC Video Converter Added support for AYUV video format. MpcAudioRenderer Improved input format validation. Optimized retrieval of supported formats for exclusive mode. Added the "Keep audio device active when paused" setting. Fixed crashes and freezes in various situations. Subtitles Added the ability to open the properties of an external subtitle renderer in the "Subtitles" settings panel. Fixed external subtitle connections for VSFilter. Fixed a crash when rendering PGS/SUP subtitles when using AVX2. YouTube Improved support for yt-dlp. The built-in YouTube parser is no longer used. Player The HTTP read strategy has been changed. If the playlist contains one entry, more key combinations can be used to control the player (jump through chapters, adjust volume). Improved support for reading ASX playlists. The translation of the MediaInfo report for Chinese, Korean and Japanese has been removed. Added blocking of 32-bit filter "PICVideo Lossless JPEG Decompressor" (pvljpg20.dll), because it crashes. Added blocking of the system filter "AVI Decompressor", which will eliminate the crash of VFW codecs. Fixed a rare crash when using the "/slave" key. Fixed a crash when getting a list of fonts for OSD. Added the ability to load an external audio file using hotkeys. Fixed opening a network path starting with \?\UNC. The "Determine duration when adding" playlist setting now works for YouTube video URLs. The "Online media services" settings panel has been redesigned. Added a "Merge files using FFmpeg" option to the file saving dialog. This option is activated when playing multiple streams obtained using yt-dlp. Added loading of local .dpl playlists ("DAUMPLAYLIST"). Fixed a hang when the user closes the player during the URL opening process. Various interface fixes. Installer Updated MPC Video Renderer 0.10.5. Updated MPC Script Source 0.2.17. Added MPC Image Source 0.3.6. Translations Updated Japanese translation (by tsubasanouta). Updated Chinese (Traditional) and Dutch translation (by beter). Updated Romanian translation (by Andrei Miloiu). Updated Hungarian translation (by mickey). Updated Turkish translation (by cmhrky). Updated German translation (by Klaus1189). Updated Chinese (Simplified) translation (by wushantao). Updated Italian translation (by mapi68). Updated Korean translation (by Hackjjang). Updated Chinese (Traditional) (by udfbe). Updated libraries dav1d 1.5.3-6-g04b69f9; ffmpeg n8.2-dev-1857-g4653e68aab; libpng git-v1.6.55-9-g7d52a8087; Little-CMS git-lcms2.18-26-gf739cda; MediaInfo git-v26.05-38-g702c9b7fd; ZenLib git-v0.4.41-91-g073f297; zlib 1.3.2. Download: MPC-BE 64-bit | Portable MPC-BE 64-bit | ~20.0 MB (Open Source) Download: MPC-BE 32-bit | Portable MPC-BE 32-bit Link: Media Player Classic - BE Home Page Get alerted to all of our Software updates on Twitter at @NeowinSoftware
    • Apple reportedly looks to blacklisted Chinese memory chips as RAM prices climb by Karthik Mudaliar Image via Apple Apple is reportedly trying to get a clearance from the Trump administration to buy memory from ChangXin Memory Technologies (CXMT) to get some relief from soaring DRAM prices. As per a report by the Financial Times, Apple approached the Commerce Department more than a month ago and also spoke to other officials and allies in Washington. For starters, CXMT is a company that's already been placed on the Pentagon's list of Chinese military companies. The Chinese company is the country's top DRAM maker. For Apple, the timing is certainly awkward but not surprising. Tim Cook had recently warned that Apple would have to raise prices because AI companies are buying up large amounts of memory for data centers, and just like that, Apple raised MacBook and iPad prices. Micron also recently revealed that customers have committed billions of dollars to secure memory supply years in advance, which shows us how aggressive securing infrastructure has become. This gives suppliers such as Samsung, SK Hynix, and Micron more leverage, while pushing hardware makers to look for alternatives. CXMT is one of those alternatives, but not the simplest one. Apple has spent many years trying to diversify parts of its supply chain away from China, especially for final assembly, while still depending heavily on Chinese manufacturing and suppliers. Even domestic brands from China are moving towards CXMT and YMTC instead of relying on Samsung, Micron, and SK Hynix. For Apple, though, it would invite more scrutiny than local Chinese companies. For now, this is more like a lobbying effort rather than a confirmed supply deal. There's no official statement from either of the parties. What is clearer, though, is the pressure behind such a request. AI demand has certainly made hardware a bottleneck, and companies are trying everything they can to bring things back to normal, even if that means making politically sensitive choices. Source: Financial Times
  • Recent Achievements

    • Week One Done
      flexorcist earned a badge
      Week One Done
    • One Month Later
      Woland13 earned a badge
      One Month Later
    • Week One Done
      Woland13 earned a badge
      Week One Done
    • One Year In
      bernmeister earned a badge
      One Year In
    • Week One Done
      Scoobystu earned a badge
      Week One Done
  • Popular Contributors

    1. 1
      +primortal
      498
    2. 2
      +Edouard
      225
    3. 3
      PsYcHoKiLLa
      148
    4. 4
      Steven P.
      74
    5. 5
      FloatingFatMan
      70
  • Tell a friend

    Love Neowin? Tell a friend!