Recommended Posts

Other then Falcon Heavy, are there any other launchers that could get this to the moon?

 

Also with regards to Space X and Starship, as much as I do believe this will ultimately replace Orion and any of the others that are in development. We do have to keep in mind that we're still pretty early in it's development cycle. It took Space X a good 2-3 years to nail the take off and landing with the Grasshopper, Falcon 1 and then  finally 9. Whilst some of that knowledge they gained will be transferable, it's not all applicable and it's on a much larger scale so we shouldn't get our hopes up on Elon's timescales too much. 

 

As far as I know they haven't even began to think about life support systems on the ship yet have they? I'm not sure if that's Mars specific or just in general?

21 hours ago, Skiver said:

Other then Falcon Heavy, are there any other launchers that could get this to the moon?

 

Once/if the Blue Origin BE-4 engine gets sorted out, the Blue Origin New Glenn or the ULA Vulcan-Centaur 5 Long Heavy (larger upper stage tanks & 6 solid  boosters), but those are delayed by Blue Origin's BE-4 engine problems.  

 

Quote

Also with regards to Space X and Starship, as much as I do believe this will ultimately replace Orion and any of the others that are in development. We do have to keep in mind that we're still pretty early in it's development cycle. It took Space X a good 2-3 years to nail the take off and landing with the Grasshopper, Falcon 1 and then  finally 9. Whilst some of that knowledge they gained will be transferable, it's not all applicable and it's on a much larger scale so we shouldn't get our hopes up on Elon's timescales too much. 

 

A key event will be a full Starship update in late October. 

 

While they're testing the SN-05 and SN-06 propulsion modules for short hops, the ramp to high altitude testing and skydiver landing tests is accelerating; 

SN-08 to SN-11 are already being built, all full airframes, and the tanks for Super Heavy #1 are already under construction. The High Bay (vehicle assembly building) is being topped off, and the orbital launch table is also well along. Its 6 legs are almost ready for their concrete pours.

 

That update should be fun.

 

Quote

As far as I know they haven't even began to think about life support systems on the ship yet have they? I'm not sure if that's Mars specific or just in general?

 

The huge volume of air in a Crew  Starship (850-1000 cubic meters vs. 10 for Crew Dragon) would provide a huge buffer. A 4 person crew could survive weeks with nothing more than fans to keep the air circuculating, CO2 scrubbers, filters,  humidity control and a supplementary O2 tank. More than enough for lunar missions.

 

Also pack a couple microwave ovens, freezers for frozen meals, and two of Crew Dragon's toilets (one of each a spare).

 

Mars would need a more involved recycling environmental control system, and they have been working on one.  So has a team of Honeywell and Paragon SDC, both ISS contractors, for commercial exploration vehicles.

  • Like 3
  • 2 months later...
  • 1 month later...

GAO has again reamed NASAs backside  over SLS & Orion. Costs, more delays, and the current delays do not take into account those caused by CoVid-19.

 

Summary,

 

https://www.gao.gov/products/GAO-21-105#summary

Quote

 

>

The National Aeronautics and Space Administration (NASA) again delayed the planned launch date for Artemis I, the first uncrewed test flight involving three closely related human spaceflight programs—the Orion crew vehicle, Space Launch System (SLS), and Exploration Ground Systems (EGS). Together, these programs aim to continue human space exploration beyond low-Earth orbit. The most recent delay, to November 2021, resulted in part from manufacturing challenges and represents a 36-month slip since NASA established a schedule to measure performance in 2014. This new launch date does not account for the effects of COVID-19. According to NASA officials, COVID-19 delays and schedule risks will place pressure on NASA's ability to achieve this launch date.

 

Development cost estimates for key programs also increased. The cost of the SLS program increased by 42.5 percent and the EGS program by 32.3 percent since 2014, for a combined increase of over $3 billion, bringing the total to $11.5 billion. NASA does not plan to complete revised estimates for Orion, which are tied to the second, crewed test flight (Artemis II) before spring 2021.

> etc.

 

 

  • 2 weeks later...

I hope this is the right thread, I couldn't find one for the Lunar mission (except for the Orion ship updates) this is for the rocket itself that will take them there

 

_116498583_maf_20191107_engine20section20full_jude-3198large.jpg

Quote

 

The four main engines of Nasa's new "megarocket" are to be fired in unison for the first time, demonstrating the launcher's raw, explosive power.

 

The Space Launch System (SLS) is part of the US space agency's Artemis programme, which aims to put Americans back on the lunar surface by 2024.

 

The engine "hotfire" is the last in a series of tests known as the Green Run.

 

It will help Nasa certify the rocket for its maiden flight, scheduled to take place later this year.

 

This uncrewed mission, called Artemis-1, will launch Nasa's next generation spacecraft, Orion, on a loop around the Moon.

 

Saturday's eight-minute ground test - due to take place within a two-hour window from 22:00-00:00 GMT (17:00-19:00 EST) - is designed to simulate the rocket's climb to orbit.

 

The core stage will be anchored to a steel structure called the B-2 test stand on the grounds of Nasa's Stennis Space Center near Bay St Louis, Mississippi.

 

Once ignited, the four RS-25 engines at the base of the core will generate 1.6 million lbs (7 Meganewtons) of thrust - the force that propels a rocket through the air.

 

Source: https://www.bbc.com/news/science-environment-54583588

 

 

_115098518_dsc_2860orig.jpg

Images: NASA

 

And here is where the live stream will be:

 

 

Steve P's post about the SLS Green Run (static fire), which should be done this afternoon (Saturday, Jan 16, 2021), got mislocated so here's a link. It should be streamed on NASA TV. Ignition is estimated at 1700 Eastern.

 

 

Edited by DocM

The SLS Green Run should burn for 8 minutes, and in spite of the size, fire & fury it has about the same thrust as a Falcon 9, roughly 1.7 million pound-force. Most of SLS's liftoff thrust comes from the 2 solid boosters (SRBs). 

14 hours ago, DocM said:

The SLS Green Run should burn for 8 minutes, and in spite of the size, fire & fury it has about the same thrust as a Falcon 9, roughly 1.7 million pound-force. Most of SLS's liftoff thrust comes from the 2 solid boosters (SRBs). 

 

The SLS Green Run burn aborted after 67.7 seconds.

 

Cause: a Major Component Failure (MCF)  signal from engine #4.

 

A FID (Failure ID) from #4 hit the controller, which then triggered a Major Component Failure (MCF) and did the shutdown. There was also a flash from the engine.

 

Also; even though they've done several Wet Dress Rehearsals (WDRs), this was the first time tanks filled with cryogenic propellants were pressurized to flight levels (!!)

 

There are spare engines at Stennis, and the first guess at a turnaround for Green Run 2 is 3-4 weeks. Bridenstine didn't sound very confident about Artemis 1 flying this year.

 

 

  • 3 weeks later...

Space Launch System advocate Sen. Richard Shelby (R-Alabama) does not intend to  run for re-election in 2022.

 

https://www.theintelligencer.com/news/article/AP-sources-Alabama-senator-has-indicated-he-15928534.php

 

  • Like 1
  • 3 weeks later...

You just had to know this was coming...

 

Green Run 2 postponed

 

https://spacenews.com/nasa-postpones-second-sls-green-run-test/

 

Quote

 

NASA postpones second SLS Green Run test

 

WASHINGTON — Just days after NASA said it was ready to perform a second static-fire test of the Space Launch System core stage, the agency announced Feb. 22 that the test would be delayed because of a valve problem.

 

NASA said it was postponing the Green Run static-fire test, which had been scheduled for Feb. 25, after discovering a problem with one of eight valves called “prevalves” associated with the stage’s four RS-25 main engines. The valve, which supplies liquid oxygen, was “not working properly,” NASA said in a statement, but didn’t elaborate on the problem.

 

Engineers identified the problem during preparations over the weekend for the test. NASA said it will work with Boeing, the prime contractor for the core stage, to “identify a path forward in the days ahead and reschedule the hot fire test” but did not set a new date for the test.

>

 

 

  • 8 months later...

Its stacked and ready to go, in 3-4 months, it blows my mind how slow this thing still is. I expected that once they got to this stage, there couldnt be as many ways to slow it down.

  • Like 1
On 24/10/2021 at 18:21, IsItPluggedIn said:

Its stacked and ready to go, in 3-4 months, it blows my mind how slow this thing still is. I expected that once they got to this stage, there couldnt be as many ways to slow it down.

 

With Boeing as the prime contractor, if there's a way they'll find it. 

  • Haha 2
  • 2 years later...

<speechless🤦‍♂️

Just for the record, NASA has been working on Orion for about 20 years.

More problems, this time they're having an issue with the side hatch.  They want to fly a crew around the Moon later this year on the Artemis 2 mission, but that means resolving numerous problems. Heat shield (working on this for 10 years), life control system, batteries. And now this.

https://spacenews.com/nasa-studying-issues-with-orion-hatch-design/

 

  • Facepalm 1
  • 8 months later...
  • 2 months later...

The Space Launch System (SLS), Boeing being the main contractor, could be canceled as soon as March or April, a victim of it's unaffordability. Orion will probably die with it. 

Artemis Moon missions will likely be completely handed over to SpaceX and  Blue Origin, who previously were only going to provide the landers.

 

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Posts

    • Onkyo Dolby Atmos AV receivers are really solid deals by Sayan Sen Recently we covered great deals on several soundbar models from the likes of Sony, JBL, Samsung and others for really good prices (the lowest in several months). Aside from that we also reported on the Edifier S3000MKII, a hi-fi two-way bookshelf monitor that's available for only $800. Today we bring a list of AV receivers from Onkyo that are available at great prices including the Onkyo NR7100, RZ30, and 8470 (purchase links under the specs table down below). The Onkyo TX-NR7100 and Onkyo TX-RZ30 are both 9.2-channel AV receivers designed for immersive home theater setups but they occupy slightly different tiers within Onkyo’s lineup with the RZ30 positioned as the more advanced model. The TX-NR7100 is a THX Certified 9.2-channel receiver offering up to 100 W per channel (8 ohms, 2 channels driven). It supports Dolby Atmos, DTS:X, and IMAX Enhanced formats, with flexible configurations such as 5.1.4 or 7.1.2 speaker layouts. A key highlight is its built-in Dirac Live Room Correction which should help optimize sound based on your room and its acoustics. In comparison, both models share several core capabilities though the RZ30 is geared toward enthusiasts seeking more precise calibration and system flexibility, while the NR7100 is positioned as a slightly more accessible, value-focused option with strong all-round performance. The technical specs of the RZ30 and NR7100 9.2 AVRs are given in the table below: Specification Onkyo TX-RZ30 Onkyo TX-NR7100 Power Output (FTC, 2ch driven) ~100 W/ch (8Ω, 20Hz–20kHz, 0.08% THD) 100 W/ch (8Ω, 20Hz–20kHz, 0.08% THD) Dynamic / Peak Power 9 × 170 W (6Ω, 1kHz, 1% THD, 1ch driven) 220 W/ch (6Ω, 1kHz, 10% THD, 1ch driven) Frequency Response 5 Hz – 100 kHz (+1/-3 dB) 10 Hz – 100 kHz (+1/-3 dB) THD 0.08% 0.08% Room Correction Dirac Live (full bandwidth) Dirac Live (with AccuReflex support) Immersive Audio Dolby Atmos, DTS:X, IMAX Enhanced Dolby Atmos, DTS:X, IMAX Enhanced Speaker Layout Support Up to 7.2.2 / 5.2.4 / 9.2 processing Up to 7.2.4 / 5.2.4 / 9.2 processing HDMI Inputs / Outputs 6 inputs / 2 outputs (eARC) 6 inputs / 2 outputs (Main + Sub/Zone 2) HDMI 2.1 Support 8K/60, 4K/120, VRR, ALLM, QFT, DSC, eARC 8K/60, 4K/120, VRR, ALLM, QFT, DSC, eARC Video Formats HDR10+, Dolby Vision, HDCP 2.3 HDR10+, Dolby Vision, HDCP 2.3 Streaming / Network Wi-Fi, AirPlay 2, Chromecast, Bluetooth, DTS Play-Fi Wi-Fi, AirPlay 2, Chromecast, Bluetooth, DTS Play-Fi Get them at the links below: Onkyo TX-RZ30 9.2-Channel AV Receiver: $797.00 (Sold and shipped by Electronic Expo) Onkyo TX-NR7100 9.2-Channel AV Receiver: $699.00 (Sold and shipped by Adorma) Onkyo TX-8470 2 Ch Stereo Receiver: $449.00 (Sold and Shipped by Adorma) Good to know This Amazon deal is U.S. specific, and not available in other regions unless specified. We only use first-party seller links or authorized dealer links (at the time of article publishing); ensure that you purchase from such links only. Check out Today's Deals on Amazon | or our recent tech deals. Become a Prime member (for Students or SNAP) via Neowin Get Prime Access - Prime for half price (for qualifying Medicaid, EBT, SNAP) Subscribe to Prime Video, Audible Plus, Music Unlimited or Kindle Unlimited via Neowin As an Amazon Associate, we earn from qualifying purchases.
    • A different thing with Russia. When you say is it better, depends on things. It is better that we don't have the E.U making rules and laws that have nothing to do with them. Is the trading part better? No, that is really mucked up, but then we knew that was going to happen and we would have make agreements, like we do with other parts of the world. Freedom of movement is certainly better, but could be improved, we still need more control over our borders. do you live in the U.K?
    • So what am I quoting from them? I never listened to what Farage or his cronies said. I wanted the U.K to leave the E.u years before the referendum and it had nothing to do with Farage and his cronies. So what country do you live in? Did we work much better together? We were always at logger heads with the E.U because we disagreed with them so much. Maggie was always on at them. I would have thought the E.U was glad to get rid of us as we stopped the integration or made it a two tier. Now without us they can integrate more. I would not have voted out if it was just a trading block and we can still work together on somethings.
    • MPC-BE 1.9.0 by Razvan Serea Media Player Classic - BE is a free and open source audio and video player for Windows. Media Player Classic - BE is based on the original "Media Player Classic" project (Gabest) and "Media Player Classic Home Cinema" project (Casimir666), contains additional features and bug fixes. The BE mod (Black Edition Mod) is a skinned version of Media Player Classic Home Cinema, much better looking than the plain old MPC. MPC-BE 1.9.0 changelog: Splitters Fixed crashes in some situations. AudioSplitter Added support for the RF64 format. Fixed reading of channel layout for some WavPack files. Added support for ID3 tags for Wave64 files. Unknown Wave64 chunks are now ignored. AviSplitter Added support for 'y408' video. Improved support for 'HEVC' video. FLVSplitter Added support for VVC video. MP4Splitter Improved handling of corrupted files. MatroskaSplitter Expanded support for V_UNCOMPRESSED video codecs. Fixed support for frame rotation (ProjectionPoseRoll). Improved support for "V_MS/VFW/FOURCC / HEVC". MpcDvdVideoDecoder Fixed conversion to YUY2. Fixed display of menus for some DVD-Videos. RoQVideoDecoder Output in NV12 and YV12 formats is allowed. Full range is used. MPC Video Decoder RGB32 format will be output as a top-down bitmap by default. Added support for the "IID_MediaSideDataDOVIMetadataV2" interface. Removed support for the deprecated "IID_MediaSideDataDOVIMetadata" interface. Fixed retrieving the name of the video adapter when using NVDEC. Fixed crashes in some situations. MPC Video Converter Added support for AYUV video format. MpcAudioRenderer Improved input format validation. Optimized retrieval of supported formats for exclusive mode. Added the "Keep audio device active when paused" setting. Fixed crashes and freezes in various situations. Subtitles Added the ability to open the properties of an external subtitle renderer in the "Subtitles" settings panel. Fixed external subtitle connections for VSFilter. Fixed a crash when rendering PGS/SUP subtitles when using AVX2. YouTube Improved support for yt-dlp. The built-in YouTube parser is no longer used. Player The HTTP read strategy has been changed. If the playlist contains one entry, more key combinations can be used to control the player (jump through chapters, adjust volume). Improved support for reading ASX playlists. The translation of the MediaInfo report for Chinese, Korean and Japanese has been removed. Added blocking of 32-bit filter "PICVideo Lossless JPEG Decompressor" (pvljpg20.dll), because it crashes. Added blocking of the system filter "AVI Decompressor", which will eliminate the crash of VFW codecs. Fixed a rare crash when using the "/slave" key. Fixed a crash when getting a list of fonts for OSD. Added the ability to load an external audio file using hotkeys. Fixed opening a network path starting with \?\UNC. The "Determine duration when adding" playlist setting now works for YouTube video URLs. The "Online media services" settings panel has been redesigned. Added a "Merge files using FFmpeg" option to the file saving dialog. This option is activated when playing multiple streams obtained using yt-dlp. Added loading of local .dpl playlists ("DAUMPLAYLIST"). Fixed a hang when the user closes the player during the URL opening process. Various interface fixes. Installer Updated MPC Video Renderer 0.10.5. Updated MPC Script Source 0.2.17. Added MPC Image Source 0.3.6. Translations Updated Japanese translation (by tsubasanouta). Updated Chinese (Traditional) and Dutch translation (by beter). Updated Romanian translation (by Andrei Miloiu). Updated Hungarian translation (by mickey). Updated Turkish translation (by cmhrky). Updated German translation (by Klaus1189). Updated Chinese (Simplified) translation (by wushantao). Updated Italian translation (by mapi68). Updated Korean translation (by Hackjjang). Updated Chinese (Traditional) (by udfbe). Updated libraries dav1d 1.5.3-6-g04b69f9; ffmpeg n8.2-dev-1857-g4653e68aab; libpng git-v1.6.55-9-g7d52a8087; Little-CMS git-lcms2.18-26-gf739cda; MediaInfo git-v26.05-38-g702c9b7fd; ZenLib git-v0.4.41-91-g073f297; zlib 1.3.2. Download: MPC-BE 64-bit | Portable MPC-BE 64-bit | ~20.0 MB (Open Source) Download: MPC-BE 32-bit | Portable MPC-BE 32-bit Link: Media Player Classic - BE Home Page Get alerted to all of our Software updates on Twitter at @NeowinSoftware
    • Apple reportedly looks to blacklisted Chinese memory chips as RAM prices climb by Karthik Mudaliar Image via Apple Apple is reportedly trying to get a clearance from the Trump administration to buy memory from ChangXin Memory Technologies (CXMT) to get some relief from soaring DRAM prices. As per a report by the Financial Times, Apple approached the Commerce Department more than a month ago and also spoke to other officials and allies in Washington. For starters, CXMT is a company that's already been placed on the Pentagon's list of Chinese military companies. The Chinese company is the country's top DRAM maker. For Apple, the timing is certainly awkward but not surprising. Tim Cook had recently warned that Apple would have to raise prices because AI companies are buying up large amounts of memory for data centers, and just like that, Apple raised MacBook and iPad prices. Micron also recently revealed that customers have committed billions of dollars to secure memory supply years in advance, which shows us how aggressive securing infrastructure has become. This gives suppliers such as Samsung, SK Hynix, and Micron more leverage, while pushing hardware makers to look for alternatives. CXMT is one of those alternatives, but not the simplest one. Apple has spent many years trying to diversify parts of its supply chain away from China, especially for final assembly, while still depending heavily on Chinese manufacturing and suppliers. Even domestic brands from China are moving towards CXMT and YMTC instead of relying on Samsung, Micron, and SK Hynix. For Apple, though, it would invite more scrutiny than local Chinese companies. For now, this is more like a lobbying effort rather than a confirmed supply deal. There's no official statement from either of the parties. What is clearer, though, is the pressure behind such a request. AI demand has certainly made hardware a bottleneck, and companies are trying everything they can to bring things back to normal, even if that means making politically sensitive choices. Source: Financial Times
  • Recent Achievements

    • Week One Done
      flexorcist earned a badge
      Week One Done
    • One Month Later
      Woland13 earned a badge
      One Month Later
    • Week One Done
      Woland13 earned a badge
      Week One Done
    • One Year In
      bernmeister earned a badge
      One Year In
    • Week One Done
      Scoobystu earned a badge
      Week One Done
  • Popular Contributors

    1. 1
      +primortal
      493
    2. 2
      +Edouard
      227
    3. 3
      PsYcHoKiLLa
      148
    4. 4
      Steven P.
      75
    5. 5
      FloatingFatMan
      70
  • Tell a friend

    Love Neowin? Tell a friend!