Recommended Posts

i have a weird network issue wherein my two network adapters get both an address via DHCP and also a Link Local IP address. (see screenshot). the two adapters are connected to two different networks with different dhcp servers. i have a feeling that this is a remnant from creating a bridge connections between the two adapters. this is an issue as in certain software that checks the IP address it detects and uses the link local ip address.

 

post-42710-0-99103300-1407170650.png

 

i have tried resetting network settings, resetting winsock. uninstalling the network adapter and adding it again but the problem seems to persists. i wanted to know if anyone has any clue on removing this link local address. it seems to only occur on the two network cards that i had created a bridge on earlier and deleted it.

 

any help is greatly appreciated 

 

do you have anything configured in your alternate configuration tab in the ipv4 properties within that adapter?

 

I believe this outlines your issue.  The default is automatic private ip address

http://www.eightforums.com/tutorials/29241-ip-address-enable-alternate-configuration.html

Another possible cause is that there is another computer with that ip address on the network.  If that is the case, you will need to change the static ip of that computer or reserve that ip in your dhcp for that other computer. 

I recall someone else having this issue awhile back and don't recall the exact cause - but this seems like a repeated problem. Hopefully the details will come to me here in a bit.

So what is this nic, its not dual port? is this the built in nic?

Arrggh its going to drive me nuts until I recall this previous thread now ;)

@sc302 the DHCP ip address 192.168.104.81 is reserved for the computer on the DHCP server so there is no conflict as far as i can tell. 

 

@budman the computer is laptop (Dell Precision M4700). one network is the built intel 82xx and the other one is via a USB3 to gigabit ethernet adapter (TRENDNet TU3-ETG). the issue is on both these cards. these were the two cards i tried to set the bridge on which i later deleted. 

 

could it be an issue related to how long windows waits before detecting wether DHCP server is present on the network. whats funny though is that the DHCP ip address shows up first and after a few mins the private IP also shows up. 

So I found the thread I was thinking about

https://www.neowin.net/forum/topic/1163160-each-nic-has-2-ip-addresses-cannot-work-out-why/

His was a VM.. He never came back to the thread - so not sure what happened with this.

You could try reset of your stack.. I have never ran into this before that last thread I linked too, have never seen it - so not exactly sure what could be causing your problem. I doubt it has anything to do with the attempted bridge. Did you actually remove the bridge?

http://support.microsoft.com/kb/299357

if you go to ipv4 properties, advanced do you see anything under IPs?

example

post-14624-0-77841400-1407185113.png

I've had that happen to a couple client machines. Reset the network stack, removed all network adapters and reinstalled them with new drivers. No static IP, the DHCP server was giving out the correct address. Still the problem would persist. Unfortunately the fastest thing for me to do was reimage the machine. Hopefully you won't have to resort to that.

If your ok with it - wouldn't mind setting up a Team viewer session to look into this a bit more.

Did you read the other thread about deleting the reg key for the guid that has that other IP On it?

Can you post the output of your ipconfig /all and also this section in device manager - making sure you set show hidden.

post-14624-0-88011900-1407196710.png

another area to look would be:

HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\Interfaces\

 

 

here are a few other things to try, there are a few in this thread:

http://social.technet.microsoft.com/Forums/windowsserver/en-US/8acb7cd1-7028-4ffe-86c9-eb43041cf8b3/how-do-i-get-rid-of-second-169254xx-ipv4-address-on-windows-server-2008-sp2-x86?forum=winservergen

 

 

apparently there are a lot of causes and not one silver bullet to fix it.  you are going to have to try different things until you find the fix for you. 

I would take budman up on doing a teamviewer session...I wouldn't mind doing it either. 

Attached is the output from ipconfig/all 

 

i added the IPAutoConfigurationEnabled to 0 on all the interfaces but it still shows up as autoconfiguration enabled in ipconfig output. i have attached the registry of the interfaces module also

post-42710-0-37437800-1407226595.png post-42710-0-55559100-1407226626.png

 

 

ipconfig.txtFetching info...   interfaces.txtFetching info...

which of those guid shows 169.x address if any - don't have the time to convert the hex ;) Also look in registry if bridge is still there?

Do you have bridge left in the registry - should be here

HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\services\Bridge and BridgeMP

post-14624-0-91121900-1407238269.png

Did you reset the stack with netsh?

you could try removing those reg entries - they are not there unless a bridge has been created. I would have to test if they should be removed when you remove the bridge.

searching for the ip address in the registry did not yield any hits. 

 

as suggested by sc302 deleting the address works but it comes back at next bootup. this might be decent temporary solution until i can get around to doing a clean install. 


post-42710-0-39465700-1407253169.png

i use the MS disable IPv6 utility to disable IPv6 http://support.microsoft.com/kb/929852

 

SVGigE filter driver is the driver for a SVS Vistek GigE  camera. this was installed prior to the problem showing up. just to try i have removed it and problem is still there.

I disable ipv6 in the registry with simple command

reg add hklm\system\currentcontrolset\services\tcpip6\parameters /v DisabledComponents /t REG_DWORD /d 255

But I would then unbind the interface for sure as well.. Try unchecking that reboot to see if your apipa address is still there.

This topic is now closed to further replies.
  • Posts

    • I have always found it funny when people think in Black and White. Windows is my choice of OS, and I understand it and somewhat like it. However, I don't blindly accept or like all of it. Heck, Windows 11 is a dogs breakfast, just as Win10 was, and basically Microsoft's past 10+ years of direction. Having said that, Linux certainly has its place. And while this isn't an attack on Linux, I think the people who blindly think Linux is the answer are just as bad as blinded Windows users, if not worse. Windows is attacked for being "basic" and "bland", as is MacOS in many situations. There's a good reason they are basic and bland, and its partly why they're so popular. They targeting a broad audience. People who use their PC as a tool for work and casual browsing, or right up to people who game or programming stuff. It also needs to be robust, and hard to break. Windows has come a long way with that since the 9x days, and while still has a few vulnerabilities, it's unlikely to be unusable or unstable by messing with some settings. I however managed to destroy the stability of a Ubuntu desktop within an hour (not deliberately, I was trying to get a custom UI), and struggled to recover from it just by changing a few settings. Stupid I know, but it was so easy to break. That is why Linux can't be mainstream in its current form.
    • I mean at this point, why even have a desktop? Just open a browser window full screen and send her to her homepage. Access to anything she needs right there. Could be on Linux, could be on Android, heck could also be on Windows 11. No one would know!
    • Will be replacing my last 2 Windows 10 PC's in household ASAP, if they could upgrade now i've done it already. Main Desktop runs Windows 11 already, that ones all set. Now just to get the other 2 all set asap
    • I think you answered why it gets so much attention in your comment. It's designed to make Windows accessible to everyone! It's a core component of the Windows UI, and 30 years of its existence is why it remains such a key component and receives so much attention to this day!
  • Recent Achievements

    • Reacting Well
      pelaird earned a badge
      Reacting Well
    • Mentor
      The Werewolf went up a rank
      Mentor
    • First Post
      Myriachan earned a badge
      First Post
    • Week One Done
      DrRonSr earned a badge
      Week One Done
    • Week One Done
      Sharon dixon earned a badge
      Week One Done
  • Popular Contributors

    1. 1
      +primortal
      601
    2. 2
      ATLien_0
      214
    3. 3
      +FloatingFatMan
      169
    4. 4
      Michael Scrip
      152
    5. 5
      Som
      151
  • Tell a friend

    Love Neowin? Tell a friend!