Recommended Posts

i have a weird network issue wherein my two network adapters get both an address via DHCP and also a Link Local IP address. (see screenshot). the two adapters are connected to two different networks with different dhcp servers. i have a feeling that this is a remnant from creating a bridge connections between the two adapters. this is an issue as in certain software that checks the IP address it detects and uses the link local ip address.

 

post-42710-0-99103300-1407170650.png

 

i have tried resetting network settings, resetting winsock. uninstalling the network adapter and adding it again but the problem seems to persists. i wanted to know if anyone has any clue on removing this link local address. it seems to only occur on the two network cards that i had created a bridge on earlier and deleted it.

 

any help is greatly appreciated 

 

do you have anything configured in your alternate configuration tab in the ipv4 properties within that adapter?

 

I believe this outlines your issue.  The default is automatic private ip address

http://www.eightforums.com/tutorials/29241-ip-address-enable-alternate-configuration.html

Another possible cause is that there is another computer with that ip address on the network.  If that is the case, you will need to change the static ip of that computer or reserve that ip in your dhcp for that other computer. 

I recall someone else having this issue awhile back and don't recall the exact cause - but this seems like a repeated problem. Hopefully the details will come to me here in a bit.

So what is this nic, its not dual port? is this the built in nic?

Arrggh its going to drive me nuts until I recall this previous thread now ;)

@sc302 the DHCP ip address 192.168.104.81 is reserved for the computer on the DHCP server so there is no conflict as far as i can tell. 

 

@budman the computer is laptop (Dell Precision M4700). one network is the built intel 82xx and the other one is via a USB3 to gigabit ethernet adapter (TRENDNet TU3-ETG). the issue is on both these cards. these were the two cards i tried to set the bridge on which i later deleted. 

 

could it be an issue related to how long windows waits before detecting wether DHCP server is present on the network. whats funny though is that the DHCP ip address shows up first and after a few mins the private IP also shows up. 

So I found the thread I was thinking about

https://www.neowin.net/forum/topic/1163160-each-nic-has-2-ip-addresses-cannot-work-out-why/

His was a VM.. He never came back to the thread - so not sure what happened with this.

You could try reset of your stack.. I have never ran into this before that last thread I linked too, have never seen it - so not exactly sure what could be causing your problem. I doubt it has anything to do with the attempted bridge. Did you actually remove the bridge?

http://support.microsoft.com/kb/299357

if you go to ipv4 properties, advanced do you see anything under IPs?

example

post-14624-0-77841400-1407185113.png

I've had that happen to a couple client machines. Reset the network stack, removed all network adapters and reinstalled them with new drivers. No static IP, the DHCP server was giving out the correct address. Still the problem would persist. Unfortunately the fastest thing for me to do was reimage the machine. Hopefully you won't have to resort to that.

If your ok with it - wouldn't mind setting up a Team viewer session to look into this a bit more.

Did you read the other thread about deleting the reg key for the guid that has that other IP On it?

Can you post the output of your ipconfig /all and also this section in device manager - making sure you set show hidden.

post-14624-0-88011900-1407196710.png

another area to look would be:

HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\Interfaces\

 

 

here are a few other things to try, there are a few in this thread:

http://social.technet.microsoft.com/Forums/windowsserver/en-US/8acb7cd1-7028-4ffe-86c9-eb43041cf8b3/how-do-i-get-rid-of-second-169254xx-ipv4-address-on-windows-server-2008-sp2-x86?forum=winservergen

 

 

apparently there are a lot of causes and not one silver bullet to fix it.  you are going to have to try different things until you find the fix for you. 

I would take budman up on doing a teamviewer session...I wouldn't mind doing it either. 

Attached is the output from ipconfig/all 

 

i added the IPAutoConfigurationEnabled to 0 on all the interfaces but it still shows up as autoconfiguration enabled in ipconfig output. i have attached the registry of the interfaces module also

post-42710-0-37437800-1407226595.png post-42710-0-55559100-1407226626.png

 

 

ipconfig.txtFetching info...   interfaces.txtFetching info...

which of those guid shows 169.x address if any - don't have the time to convert the hex ;) Also look in registry if bridge is still there?

Do you have bridge left in the registry - should be here

HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\services\Bridge and BridgeMP

post-14624-0-91121900-1407238269.png

Did you reset the stack with netsh?

you could try removing those reg entries - they are not there unless a bridge has been created. I would have to test if they should be removed when you remove the bridge.

searching for the ip address in the registry did not yield any hits. 

 

as suggested by sc302 deleting the address works but it comes back at next bootup. this might be decent temporary solution until i can get around to doing a clean install. 


post-42710-0-39465700-1407253169.png

i use the MS disable IPv6 utility to disable IPv6 http://support.microsoft.com/kb/929852

 

SVGigE filter driver is the driver for a SVS Vistek GigE  camera. this was installed prior to the problem showing up. just to try i have removed it and problem is still there.

I disable ipv6 in the registry with simple command

reg add hklm\system\currentcontrolset\services\tcpip6\parameters /v DisabledComponents /t REG_DWORD /d 255

But I would then unbind the interface for sure as well.. Try unchecking that reboot to see if your apipa address is still there.

This topic is now closed to further replies.
  • Posts

    • A summary of the article shouldn't be an issue in theory, as the information is all based within the document itself. The problem with a lot of AI models is that they are trained off both Wikipedia as a primary source and other secondary websites which have less reliable information. As an encyclopaedia it is no doubt going to have bias in one way or another, all encyclopaedias do. The difference is that there is a process for a lot of this information to be figured out whether or not it is an opinion, or the source of that information, and to be aware of the possible bias in the first place, even your own bias as a reader. The way many people understand languages these days is quite limited, particularly in certain areas of the world. This is obvious in many types of "journalism" where some articles are thinly disguised opinion pieces, Where language is carefully curated to push a point of view despite it looking like fact. This is partly why a lot of the Western world is now so divided.
    • I paid for a year subscription, starting in December, I think. I like the user-friendliness and assets like royalty-free music and sounds. But they need to fix some of the horrific bugs before they start adding more features. For starters, you should be able to drag stuff around the timeline without it completely obliterating transitions, synchronization timing, and clip lengths. If you already set up footage and audio how you want, and try to insert more by sliding content to the right, you'll have to clean it all up again. The scroll wheel constantly stops working, and you have to minimize the window and restore it to get it back. When selecting text at the top right in special text tools, it glitches and goes to "copy" mode with a weird pop-up on top of your cursor and you can't type. These are more important than AI tools and new features. Microsoft, start by making your product less painful to use.
    • 🙄 Whats the need to launder? Do you have any reputable sources?
    • Thanks, I'll download it and see how it goes. Gonna be tough. I've used Nova Launcher for around 10+ years I think.
    • Wikipedia has become hot molasses with mostly filth masquerading as truth. Most of it is the imagination of few writers who think of themselves as above god. The narrative setup is mind boggling.
  • Recent Achievements

    • Apprentice
      Adrian Williams went up a rank
      Apprentice
    • Reacting Well
      BashOrgRu earned a badge
      Reacting Well
    • Collaborator
      CHUNWEI earned a badge
      Collaborator
    • Apprentice
      Cole Multipass went up a rank
      Apprentice
    • Posting Machine
      David Uzondu earned a badge
      Posting Machine
  • Popular Contributors

    1. 1
      +primortal
      516
    2. 2
      ATLien_0
      259
    3. 3
      +Edouard
      191
    4. 4
      +FloatingFatMan
      175
    5. 5
      snowy owl
      133
  • Tell a friend

    Love Neowin? Tell a friend!