Recommended Posts

It would seem pretty clear there is no special routing -- since both nics are in the same network and pointing to the same gateway, and from the ipconfig its also quite clear they are not teamed. Nor from his explanation of the network would there be any need for special routing - they have 1 "server" xp box ;) So what are they going need special routing to?

The so called "server" for example has a wired and wireless interface both connected to the same 192.168.1.0/24 network.. You can not "team" wired and wireless interfaces ;) Nor would there be any point to even if you could.

edit:

Which wires did you disconnect? Its quite possible you had a computer(s) with both cables connected to the dlink?

Depends on where your router is connected as well.

router (192.168.1.1) --- switch1 (dlink or linksys) --- switch2 (linksys or dlink)

or

Router -- dlink

|

linksys

You need to understand how your switches are connected to your router the gateway address shown in your ipconfig 192.168.1.1

If the linksys has enough ports (that all work) then your linksys needs to be connected to your router and the computers connected to it.

router -- linksys -- computers

Edited by BudMan

Ok the only kind of router I see is the wireless one. The modem wire goes into the router (internet port). Then there are 2 wires going out from port 1 and 2 from the router. The thing is i dont know where they go because the wiring is done on top of the ceiling.

Well I would guess the 2 cables from the router 1 and 2 lan ports go to the 2 different routers, 1 each..

If the cables are not labeled, check the lights on the switches ports.. then unplug one of the wires from routers lan ports -- which port light goes out on one of the routers.. Then do the same thing for the other one.

keep in mind this will disconnect users from the internet - so you might want to do this after hours ;)

So maybe lan 1 goes to a PC? If was lighted on the router, but when you unplugged it no lights went out on the switches? Then I would assume it went elsewhere - PC most likely.. Do you have any pcs in the building/office where the router and modem are that are not wireless?

Does a cable go from the dlink to the linksys? If so you would of had a loop, and I would assume the switches would of turned one of the interfaces off.. That is if they support STP (spanning tree protocol)

So the one that comes from the router to the dlink -- plug it into the linksys vs the dlink.. Then have 1 wire from each pc run to the linksys -- then you can remove the dlink switch.

You only need 1 connection from the router to the switch your going to use, and then 1 connection from each pc to that switch.

edit: btw that was a typo in my other post, I meant to say 2 different switches, not routers ;)

  • 2 weeks later...

What are the printers? Are they network printers? Or just usb/lpt printers?

If network -- just plug them into your switch.. And setup their IPs following their instructions to be on your network..

Then you can either connect to them from your "server" and share them - then connect the clients to this printer share, or you point each client to the printers IP directly setting up the printer on the client.

The server method is easier and has advantages. But you might have issues with XP as your server, if you have any vista clients, etc.

If you give us the details of what printers you have -- we can help more.

BudMan thanks for the help. The printer problem is very low right now a problem I am having is people getting kicked out of the network. Basically they are working on something and when they try to save it its not going to let them. Sometimes i have to click like 50 times to get into the server. The guy that built this network could not solve this issue either so I am turning to you guys for help.

thanks again for all of the help you gave me so far!

Yeah your not going to want to jump right into a CCNA course book if your sketchy on even what a switch is ;)

This might be a better starting point ;)

http://www.amazon.com/Networking-Dummies-S...e/dp/0764516779

51PAP5MRVWL._BO2,204,203,200_PIsitb-sticker-arrow-click,TopRight,35,-76_AA240_SH20_OU01_.jpg

http://www.amazon.com/Networking-All-Refer...7348&sr=1-1

51quUXURYlL._BO2,204,203,200_PIsitb-sticker-arrow-click,TopRight,35,-76_AA240_SH20_OU01_.jpg

http://www.amazon.com/Networking-Beginners...6932&sr=1-4

51HEKjqscML._BO2,204,203,200_PIsitb-sticker-arrow-click,TopRight,35,-76_AA240_SH20_OU01_.jpg

http://www.amazon.com/Sams-Teach-Yourself-...7162&sr=1-9

51zPG%207zkFL._BO2,204,203,200_PIsitb-sticker-arrow-click,TopRight,35,-76_AA240_SH20_OU01_.jpg

I am no network master by any means, but my recommendation is the same as Budman, you've got some learning/reading to do.

Ask the big bossman if he would pay for the books. If he asks why, say that he is getting off lightly as most experienced and certified Network Admins are not cheap.

I think you might be better-off building the network back up from scratch, though that is just my personal opinion

That way you can know it is being done right.

I am no network master by any means, but my recommendation is the same as Budman, you've got some learning/reading to do.

Ask the big bossman if he would pay for the books. If he asks why, say that he is getting off lightly as most experienced and certified Network Admins are not cheap.

I think you might be better-off building the network back up from scratch, though that is just my personal opinion

That way you can know it is being done right.

They are constantly working on it otherwise i would of done that. Its very weird :s

"Sometimes i have to click like 50 times to get into the server. The guy that built this network could not solve this issue either so I am turning to you guys for help."

How many users do you have again? XP pro is limited to 10 concurrent connections from other machines to file shares. Home is only 5

Is this the error your getting?

http://support.microsoft.com/kb/314882

Inbound connections limit in Windows XP

"Sometimes i have to click like 50 times to get into the server. The guy that built this network could not solve this issue either so I am turning to you guys for help."

How many users do you have again? XP pro is limited to 10 concurrent connections from other machines to file shares. Home is only 5

Is this the error your getting?

http://support.microsoft.com/kb/314882

Inbound connections limit in Windows XP

Well that solves that. Budman I dont know your name, but again THANK YOU for the great help! There is no way to raise the limit correct?

No there is no way to raise the limit - which why you don't use XP as a file/print server if you have more than a couple of users ;)

There are CHEAP/FREE alternatives to windows based OSes -- You could run something like Clark Connect, which can act as Domain.. Central userbase, file server, print server, email server, etc. etc. etc..

http://www.clarkconnect.com/

Or for soho setups - you could take a look at Microsofts SBS.. Cheapest way to setup a Active Directory with tools to make it easier to manage from microsoft, etc. You will have to purchase the number of cals to support the number of users you have, etc. It maxes out around 75 users I do believe - atleast the older 2k3 versions did.

http://www.microsoft.com/sbs/en/us/default.aspx

If your on a budget, I would really suggest you look at the clarkconnect option -- there is a FREE version to use.. Another option other than the microsoft SBS or CC is SME Server http://wiki.contribs.org/SME_Server:About

There is really is little need to resort to using XP boxes as your file server when there are FREE options that don't have such limits of how many window users can access your file shares at the same time, etc.

To be honest any linux distro running SAMBA can provide file shares to windows boxes or printers without any limit connections. But SME and CC are designed for the novice to linux user, with simple to setup interfaces and specifically designed linux distros to replace a many aspects of a windows Active Directory Domain without the MS price tag ;) Don't get me wrong its not a true 100% replacement for AD -- but for the soho business its quite often a perfect solution. And more than likely will far exceed your feature requirements -- especially if you are use to use a XP box as your "server" ;)

Edited by BudMan

Today I have been going wild i connected my laptop to the network and one of the people here could not connect because there was already 10 people connected. So i disconnected my laptop and it let them connect after 30 min. Money is not an issue as long as it fixes this issue im getting tired of it. How does Clark Connect work? How would I set it up? I dont want to mess anything up with the current set up. Thanks again BudMan.

No there is no way to raise the limit - which why you don't use XP as a file/print server if you have more than a couple of users ;)

There are CHEAP/FREE alternatives to windows based OSes -- You could run something like Clark Connect, which can act as Domain.. Central userbase, file server, print server, email server, etc. etc. etc..

http://www.clarkconnect.com/

Or for soho setups - you could take a look at Microsofts SBS.. Cheapest way to setup a Active Directory with tools to make it easier to manage from microsoft, etc. You will have to purchase the number of cals to support the number of users you have, etc. It maxes out around 75 users I do believe - atleast the older 2k3 versions did.

http://www.microsoft.com/sbs/en/us/default.aspx

If your on a budget, I would really suggest you look at the clarkconnect option -- there is a FREE version to use.. Another option other than the microsoft SBS or CC is SME Server http://wiki.contribs.org/SME_Server:About

There is really is little need to resort to using XP boxes as your file server when there are FREE options that don't have such limits of how many window users can access your file shares at the same time, etc.

To be honest any linux distro running SAMBA can provide file shares to windows boxes or printers without any limit connections. But SME and CC are designed for the novice to linux user, with simple to setup interfaces and specifically designed linux distros to replace a many aspects of a windows Active Directory Domain without the MS price tag ;) Don't get me wrong its not a true 100% replacement for AD -- but for the soho business its quite often a perfect solution. And more than likely will far exceed your feature requirements -- especially if you are use to use a XP box as your "server" ;)

If your a MS shop - and what you understand more is windows.. Then yeah I would agree the SBS route might be better for you.. But linux is a very nice option as well.. ClarkConnect has a supported version for very little dollars.. And the management interfaces are very novice friendly, etc.

So its up to you -- either way you go.. Your going to want to get a new machine for your server most likely - so that you can leave your current setup in place and just bring the new server online in parallel.

I would suggest you look into a entry level server piece of hardware vs PC type. But if you have a spare PC you could use that as a test for either option. Both CC (enterprise edition) and SBS have free trials.

But in a nutshell -- bring the new server online. Copy all the files from the current XP server to the new one.. Create the shares - create your users on the new server and then join your computers to the new domain you will create.

Worse case -- is since your not changing anything on the current server is you could always go back to how your setup now for access.

If you need help -- neowin is always here ;) No matter which option you go with, and if you need help picking out a entry level server hardware to use -- again just ask.. Lots of people here to help.

edit: Just my 2 cents is since you can try both for FREE.. Do that -- and then go with the one you like better!

Im pretty sure you will love it -- its a great distro for the soho, and you can not beat the price ;) Get yourself a nice entry level server, with a backup power supply, setup your disks in a raid and you would be rockin compared to what you have now.

This topic is now closed to further replies.
  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Posts

    • Google reportedly set to lose two key Gemini and DeepMind researchers to Anthropic by Karthik Mudaliar Google is reportedly preparing to lose two more prominent artificial intelligence researchers, with Gemini contributors Jonas Adler and Alexander Pritzel planning to join rival AI developer Anthropic. According to a report from Bloomberg, both researchers are viewed internally as important contributors to Google’s flagship Gemini model family. Adler worked on Google’s AI coding efforts, while Pritzel was involved in the process used to train AI systems. Neither company has publicly confirmed the moves. The report also does not say when the researchers will formally leave Google or what positions they will hold at Anthropic. Training a large AI model requires decisions covering its architecture, data preparation, distributed computing infrastructure, and post-training methods that shape how the finished system behaves. Researchers with experience operating at the scale of Gemini are consequently difficult to replace quickly. Both Adler and Pritzel have previously contributed to Google DeepMind’s scientific research as well. They are listed among the authors of the company’s work on expanding AlphaFold protein-structure predictions across entire proteomes, alongside AlphaFold researchers including John Jumper. The reported departures arrive shortly after another important change within Google’s Gemini organization. Gemini co-lead Noam Shazeer is leaving Google for OpenAI, after returning to the search company in 2024 through its deal with Character.AI. Shazeer is particularly well known as one of the authors of the Transformer paper, whose architecture became the foundation for most modern large language models. Anthropic, meanwhile, has been recruiting recognizable figures from other leading laboratories. OpenAI co-founder and former Tesla AI director Andrej Karpathy joined Anthropic’s pre-training team in May. His move, followed by the reported recruitment of several Google researchers, suggests Anthropic is strengthening the research teams responsible for the core capabilities of future Claude models rather than concentrating solely on product and enterprise sales. The competition is complicated by the companies’ extensive commercial relationships. Anthropic competes directly with Google’s Gemini models, but it also relies on Google as an infrastructure partner. In April, Anthropic announced an expanded agreement with Google and Broadcom covering multiple gigawatts of next-generation Tensor Processing Unit capacity. TPUs are Google-designed accelerators used to train and run large AI models. via Bloomberg
    • This article makes my head hurt. Lots of confusing words
    • Google adds built-in computer control to Gemini 3.5 flash by Karthik Mudaliar Google has added Computer Use as a built-in tool in Gemini 3.5 Flash, giving developers a single model that can reason about a task and operate graphical interfaces across browsers, mobile devices, and desktop environments. The feature is available through the Gemini API and Google’s Gemini Enterprise Agent Platform, although it remains a preview feature for now. Computer Use enables an AI agent to examine screenshots and return actions such as mouse clicks, scrolling, and keyboard input. A developer’s application must execute those actions, capture the resulting screen, and send it back to Gemini, creating a continuous loop until the task is completed. Google says the integration can be used for activities including repetitive form filling, application testing, research across multiple websites, and longer enterprise workflows. Gemini 3.5 Flash can work with browser, mobile, and desktop environments, whereas Google’s earlier standalone Computer Use model was primarily positioned around browser interaction. The main change is consolidation. Computer control was previously offered through the separate Gemini 2.5 Computer Use preview model. As Neowin reported when that model was introduced, it was designed to interpret a visual interface and generate actions without requiring a website-specific API. Google later brought Computer Use to preview versions of Gemini 3 Pro and Gemini 3 Flash in January 2026. The latest release now incorporates the tool into the stable Gemini 3.5 Flash model rather than requiring developers to select a specialized model solely for interface automation. Gemini 3.5 Flash itself was announced in May as Google’s latest fast model for coding and multi-step agent workflows. It supports a one-million-token input context window and up to 65,000 output tokens, along with adjustable thinking levels that let developers trade additional reasoning for lower latency and cost. Google also added that Gemini 3.5 Flash received targeted adversarial training for computer-use scenarios. The company is also offering safeguards that can require user confirmation before sensitive or irreversible actions and automatically stop a workflow when suspected prompt injection is detected. Its developer documentation describes configurable protections for areas such as financial transactions and changes to sensitive records. Google isn't the first to bring Computer Use to its platform. Anthropic has made computer control available through Claude, while OpenAI has continued improving computer-use performance in its recent models. Microsoft has also applied the concept to business workflows, including a Computer Use capability for the Researcher agent in Microsoft 365 Copilot.
    • After I installed KB5095093, the volume on my ARM laptop won't go above 20%. It's stuck on the hearing protection level, which is pretty much useless if you want to listen to anything. I rolled back.
    • Amazon Prime Day slashes Samsung's newest Galaxy Watch Ultra by 45 percent by Karthik Mudaliar Samsung’s flagship Android smartwatch has received one of its steepest Prime Day cuts. Amazon has dropped the 2025 Samsung Galaxy Watch Ultra in Titanium Blue to $357.24, saving buyers around $292 from its $649.99 list price. That's a 45 percent discount (purchase link below). The 47mm Galaxy Watch Ultra uses a titanium casing and a 1.5-inch Super AMOLED display with a resolution of 480 x 480 and peak brightness of 3,000 nits. It includes LTE connectivity, Bluetooth 5.3, Wi-Fi, NFC, and dual-frequency L1+L5 GPS for more accurate outdoor route tracking. The 2025 model has 64GB of storage, a 590mAh battery, sapphire crystal glass, 10ATM water resistance, IP68 protection, and MIL-STD-810H durability testing. Its health and fitness tools include heart rate monitoring, sleep coaching, Energy Score, Running Coach, body composition analysis, temperature sensing, and ECG support, where available. This model is best suited to Android users who regularly run, hike, cycle, or train outdoors and want cellular access without carrying a phone. The larger battery, rugged construction, bright display, and dedicated Quick Button also make it a stronger option than Samsung’s regular Galaxy Watch models for extended workouts and demanding environments. Grab the Titanium Blue Galaxy Watch Ultra before the Prime Day price resets: Samsung Galaxy Watch Ultra (2025) [Sold and Shipped by Amazon] Good to know This Amazon deal is U.S. specific, and not available in other regions unless specified. We only use first-party seller links (at the time of article publishing); ensure that you purchase from a first-party seller link only. Check out Today's Deals on Amazon | or our recent tech deals. Become a Prime member (for Students or SNAP) via Neowin Get Prime Access - Prime for half price (for qualifying Medicaid, EBT, SNAP) Subscribe to Prime Video, Audible Plus, Music Unlimited or Kindle Unlimited via Neowin As an Amazon Associate, we earn from qualifying purchases.
  • Recent Achievements

    • Dedicated
      Scoobystu earned a badge
      Dedicated
    • First Post
      Tom Schmidt earned a badge
      First Post
    • One Month Later
      D0nn13 earned a badge
      One Month Later
    • Rookie
      +ChiefOfNeo went up a rank
      Rookie
    • One Year In
      Tom Schmidt earned a badge
      One Year In
  • Popular Contributors

    1. 1
      +primortal
      463
    2. 2
      +Edouard
      177
    3. 3
      PsYcHoKiLLa
      124
    4. 4
      Michael Scrip
      79
    5. 5
      Xenon
      76
  • Tell a friend

    Love Neowin? Tell a friend!