Disney Employee Attacks Handicapped Child


Recommended Posts

Well my first impression is that the parent(s) are over sensationalizing this incident by stating that he has to take more medication and suffers from nightmares. That could simply be coincidences, not related to him be 'assaulted'. However, regardless, the employee most certainly should not have shoved the kid, he (the employee) should be fired at the very least, and since there is photographic evidence that this happened there could be legal action taken against this employee for at least assault. Now the parent in me says if that had been my kid being shoved, I would have kicked his ass! My friend has a boy who is non verbal autistic and he is very sweet and loving, but also misunderstood at the same time, so I could see something like this happening to him.

Well my first impression is that the parent(s) are over sensationalizing this incident by stating that he has to take more medication and suffers from nightmares. That could simply be coincidences, not related to him be 'assaulted'. However, regardless, the employee most certainly should not have shoved the kid, he (the employee) should be fired at the very least, and since there is photographic evidence that this happened there could be legal action taken against this employee for at least assault. Now the parent in me says if that had been my kid being shoved, I would have kicked his ass! My friend has a boy who is non verbal autistic and he is very sweet and loving, but also misunderstood at the same time, so I could see something like this happening to him.

I agree with you. The employee should have been a bit more professional and handle the situation better than that, however the parents are at fault too because once a parade starts, guests are not allowed to cross the lines and interfere with the cast members in any way, shape or form, so I blame the parents for the incident.

The employee was in character and took it so far to be meaner he wantd to scare the child. He should never have touched the child end of story. He was a tad aggressive in his approach but thats darth maul.... fear the sith and ****. But all in all nothing happened. The deserve free passes and a refund. The employee should be fired. Justice

I agree with you. The employee should have been a bit more professional and handle the situation better than that, however the parents are at fault too because once a parade starts, guests are not allowed to cross the lines and interfere with the cast members in any way, shape or form, so I blame the parents for the incident.

But the kid had already hi-fived another "character" (1:38), so everyone (including the parents) most likely figure it's okay as long as he doesn't run out in the middle.

Yeah, I get Darth Maul being in character, but he went too far even if the kid wasn't special needs (which he has no idea about in that encounter). Give the kid a "mean-mug" and move on.

But if it was my kid, I would've gone Obi-Wan on his ass.

But if it was my kid, I would've gone Obi-Wan on his ass.

I would hope you would do that whether your kid were disabled or not. Disabled people are not super special snowflakes, and I guarantee you that they don't WAN'T to be, either. They want to be treated exactly the same as everyone else.

Really gets up my nose when people play the disabled card on behalf of the disabled. Article title should be "Disney employee attacks child", that's it.

I would hope you would do that whether your kid were disabled or not. Disabled people are not super special snowflakes, and I guarantee you that they don't WAN'T to be, either. They want to be treated exactly the same as everyone else.

Really gets up my nose when people play the disabled card on behalf of the disabled. Article title should be "Disney employee attacks child", that's it.

three part answer

1) yes, I would do that regardless of if my child was disabled or not. in fact, from the brief encounter, it's easy to say that the Disney guy had no idea the kid was disabled at all.

2) my child is actually disabled, to the point that he can't walk and wouldn't react enough to want to high-five him anyway. he'd just sit in his stroller eating. so in that case, even more reason to club the **** out of Darth Maul if he pushed my kid.

3) as far as playing the disabled card, the fact that the kid is autistic makes it that much more damaging. it's hard for those kids to even come out of their shells enough to get that excited at a parade -- usually they would be running away from that much noise and pomp. I'm not shocked that he has nightmares now.

3) as far as playing the disabled card, the fact that the kid is autistic makes it that much more damaging. it's hard for those kids to even come out of their shells enough to get that excited at a parade -- usually they would be running away from that much noise and pomp. I'm not shocked that he has nightmares now.

I have an aspie son. I wouldn't take him anywhere NEAR a Disney parade... I'd be dealing with the fallout from it for months. Parents are idiots, tbh. (And yes, the Disney employee should be severely reprimanded/fired for shoving the kid, ANY kid. The disability part is irrelevant.)

Actually... Looks to me more like the performer was just being in character...

Anyway. 2009? This is just coming up now?!

Did you not read my post? It says:

"This is a little old but wow...Amazing what people will do to get money. Check it out and post your opinion"

  • 4 weeks later...

That kid shouldn't have been jumping into the parade like he was. Terrible parents.

Are you kidding me? How dare you refer to these people as "terrible parents." Have you ever had a child with autism? As the previous post said, he was high-fiving all the other characters and no one said anything or even discouraged him. This child was living one of the best moments of his life. I applaud his parents for providing this opportunity for him. They know what their child can and cannot handle. It wasn't their child that had the temper tantrum, it was the Disney employee. This employee should have been reprimanded. If that had been my child, I would have been at the administrative office making an official complaint. Don't judge anyone unless you have walked a mile in their shoes...

OK... I'd like to offer my feelings on this, as I have seen this video a number of times. Moreover, a girl I am seeing works for the National Autistic Society and is very VERY caring in her views. I showed this to her as she also loves Disney just to see what she thought. To sum it up:

* A lot of people use the "My son is autistic" card. Yes, your son is autistic (or rather: has autism) - but you chose to take them to Disneyworld, somewhere that they will be very much over-stimulated. And you chose to not supervise them correctly. A parent should supervise any child, and at least be "more aware" if you chose to take an autistic child somewhere like this.

* The kid ran out into the area they are NOT ALLOWED once a parade starts. I know that children are about as controllable as spinning tops, and suffering from autism will increase this. And again, the parent should have made sure this didn't happen. The kid was already at the front, and already past the boundary for quite a long time - so it shows his parents were not taking care.

* "Darth Maul" does not seem to be doing anything other than keeping in character. He DOES NOT strike the kid, that is a video angle, he is simply pushing him back. Maybe not the "best" reaction, but it was far from the situation the video makes it out to be.

* It's hugely unlikely the child would have needed further medication. He may have needed to discuss this a few times with his therapist/carer, but medication would not have solved any problem this created.

So yeah, those are her views as an appointed and qualified carer and moreover as a very kind and caring person...

But if it was my kid, I would've gone Obi-Wan on his ass.

The "attack" was nothing more than a push and was in character; that's not to say it was acceptable but that's what the complaints procedure is for. To advocate going "Obi-Wan on his ass" is immature and shows complete contempt for society and common decency. It's one thing for your emotions to take over in the heat of the moment but it's another entirely to say - when calm - that you would assault somebody that did this to your child. That's a calculated criminal offence and much, much worse that the act that precipitated it.

I highly doubt that you would actually do such a thing - I imagine you were just trying to act tough on the internet - but if you would that's very sad.

The "attack" was nothing more than a push and was in character; that's not to say it was acceptable but that's what the complaints procedure is for. To advocate going "Obi-Wan on his ass" is immature and shows complete contempt for society and common decency. It's one thing for your emotions to take over in the heat of the moment but it's another entirely to say - when calm - that you would assault somebody that did this to your child. That's a calculated criminal offence and much, much worse that the act that precipitated it.

I highly doubt that you would actually do such a thing - I imagine you were just trying to act tough on the internet - but if you would that's very sad.

I don't give a **** what you think, I would have stepped up right in his face if he pushed my kid while he was simply trying to give him a high-five (that he had just done to another "actor" less than 2 minutes before with no issues from any Disney employee telling him to stay back).

Because god forbid a Star Wars "actor" break character at a Disney event

Seriously, how over the top is this video. And the end part of it about him taking more medication etc is bull**** IMO. Yes the employee shouldn't of pushed him like that but it was not malicious and the stills make it look worse than what it is.

I knew before I even saw the video, that this involved a boy, by the use of "child" instead of a gender reference in the title. If it had been a girl, the headline would have shouted, "Disney Employees Attack Handicapped Girl", and there would be less question about the culpability of Disney or the claims of the child's family. However, you know, since boys are like, considered more disposable and stuff...

This topic is now closed to further replies.
  • Posts

    • Sihoo Doro C300 Pro V2 Ergonomic Office Chair review: The Ikea of chairs by Steven Parker I've reviewed a few gaming chairs over the past three years or so and generally found them to score well in our reviews. SIHOO reached out asking if I was interested in taking a look at their flagship chair, the Doro C300 Pro V2. I never got the chance to check out its predecessor, but the V2 is described as an "Adaptive Ergonomic Chair." It became available to buy in April of this year. Let's get things rolling with a closer look at the specifications and features. Specifications Doro C300 Pro V2 Model Ergonomic Materials Mesh Back and Seat; Soft PU Coated Armrests Height adjustability 45.5 - 53 cm / 17.5" - 20.9" Seat (w+d) 52 x 43 - 47 cm / 20.5" x 16.9" - 18.5" (adjustable) Backrest 52 – 60 cm / 20.5" - 23.6" (adjustable) Lumbar support Mesh built-in (adjustable) Armrest adjustability 8D Bionic Armrests Rocking angle 105°, 120°, 135° (fixed) Neck support Mesh built-in (adjustable) Net weight 27.3 kg / 59.64 lbs Weight support 150 kg / 330 lbs Colors Black, White Warranty 5 years (upon registering) Price $499.99, $539.99 Introduction At first glance, it looks like a chair that in another life wants to be a Herman Miller; It certainly looks like my Aeron Remastered, but the Doro C300 Pro V2 has quite a few more features and costs quite a bit less. SIHOO says that it is made up of a "DynaCore" system that tracks your movement and synchronizes the headrest, backrest, lumbar support, and armrests as you shift, twist, or recline. They also say that the "SyncroFlex Backrest" molds to your spine, which kind of describes how the mesh fabric works in most ergonomic chairs, but anyway. Below are the meat and potatoes measurements for the chair. Here is the same tech sheet, but in inches. Durability I would be remiss to not talk about the various durability testing this chair underwent before coming to market, as this is claimed on the product page. First of all, the chair is BIFMA-, SGS-, and TÜV-certified. As for durability, the tests undergone were: 100,000 Castor cycles tested 120,000 Armrest cycles tested 120,000 Recline cycles tested 120,000 Gas lift cycles tested 60,000 Armrest durability cycles tested 120,000 Rotation cycles tested Nothing about weights testing, though. Now that's all disclosed, now onto my own personal findings. Assembly The Doro C300 Pro V2 came in two large boxes (1) (2), and everything was packed very well, protecting the different parts of the chair. In the box, there is a folded sheet that explains the 12 steps to assemble it; they are: Remove the bottom cover on the aluminum base; Insert the five legs into the aluminum base and use ten screws to fasten them; Insert the castors into the legs; Replace the bottom cover on the bottom of the aluminum base; Place the Class 4 Hydraulics gas cylinder into the aluminum base; Screw the bottom part of the arm rests, taking care of the orientation using two screws on each side; Use three torx screws to fasten the footrest to the bottom of the seat; Fasten the backrest to the seat using four torx bolts; Fasten the armrests to the backrest using four Torx bolts (two on each side), taking care to note the orientation; Place the chair onto the Class 4 Hydraulics gas cylinder; Insert the headrest into the top of the backrest; Use two torx screws to fasten the headrest to the backrest. There's also an online guide you can refer to. Carefully unpacking the two boxes took around 15 minutes because almost everything is wrapped in plastic and protective foam; the chair assembly itself took around an hour. I say in the above assembly steps to take note of the orientation, because it's not obvious which way around the bottom portion of the armrests go, and although there is an L and R on the bottom of the armrests, it also wasn't clear from the instructions which was actually left or right, facing the chair, or in the seated down orientation? Anyway, I ended up putting the bottom portions on the wrong sides, and after securing one of the armrests, I discovered that although it was on the correct side, the armrest base could rotate a full 360°, but not when bolted to the chair, so I had to remove it, rotate it, and then bolt it back on. Truly an Ikea experience! Also, to complicate things further, although all the parts are labeled from A to X (yes, that's 24 parts) unhelpfully, these letters do not appear on the parts themselves or the package with the bolts, screws, and washers. There's also a pair of protective gloves in the box, but I think they were made for much smaller hands than I have. Even my friend, who is 5.1, had difficulty putting them on. Once assembled, I needed to sit down. Anyway, as I said, it looks quite similar to my Herman Miller. And here is the back of it. If you look at the product page and on Amazon, it seems like a lot of thought has gone into the chair itself and what it's capable of, but there is no mention at all about the castors, and this is an area where I think the chair trips up quite quickly. I found it difficult to move the chair in any direction. I asked a friend who came to visit me earlier this week to test my findings, and she said that the wheels were "no good," so it definitely isn't just me. I am 6'2 myself and a big guy, I work from home and gained a few pounds from mostly staying in and the hell away from other people. However, the Doro C300 Pro V2 is rated for up to 150kg (330lbs), which in my case is used well within its max rating. Ergonomics The number of adjustments you can make, right up to setting it in nap mode — which I haven't fully tested yet — is what you'd expect from a premium chair. Yes, you can go up and down (max 7.5 cm adjustment), rock back and forth (with tilt adjustment), and lock the chair between three stages of 105°, 120°, 135°, which is not quite as flat as the AndaSeat I tested at 160°. Some thought has also gone into the "8D" armrests, too, which are cushioned but quite firm; you'll only know it if you press hard into the PU-covered tops, which give about half a centimeter, but it's enough to ensure your skin won't get awkwardly stuck to it in warmer (or sweatier) conditions. It almost feels like plastic and is very easy to keep clean. However, the armrest positions move far too easily, and I am not sure what that "elbow" function is. Maybe it is good for a short person with short arms, anyway, I never used it and kept it flat at all times. There are eight levels of adjustment for the armrests, they are: backwards, forwards, swing left/right, height up and down, tilt, and 360° rotation, which can be handy for desk clearance. As I said, the armrest pads shift far too easily, which could give off an ergonomic vibe, but who wants the armrest sliding when you are shifting weight? The height adjustability does lock into place when lifting and adjusting. Comfort This is ultimately what it boils down to at the end of the day, right? Quite a lot of reviews praise the comfort of this chair, and I don't disagree that the mesh seating is quite comfortable. I am used to the material from my daily Herman Miller. However, the backrest cannot be locked into place, and this is actually a feature; as you shift or recline yourself on the chair, the backrest moves with your body. It took some getting used to. The lumbar gives ample support, but I would have preferred an adjustable one built into the seat base, as this causes the backrest to move up and down at will. Again, as with my previous chair review, this chair is also rated for tall people, but nowhere in the product documentation does it say how tall. Being 6'2 myself, I'm happy to say that the backrest is tall and wide enough, and thought has been given to being able to adjust the neck rest, but as others have mentioned in their reviews, people as tall as 6.2ft is about the limit for the neckrest. Conclusion What I didn't like The footrest is rated for 15kg (33 lbs), which to me seems a bit light, and after looking online, it seems like a chair footrest for adults must be at least twice that rating. In all honesty, they are just hollow metal tubes, so it is not recommended to let a kid sit on them. I also feel like it doesn't really go out far enough for my height, so that kind of puts the dampener on me being able to use it regularly. I'll just have to continue to use my subwoofer as a footrest! I do not like the armrests being able to shift around as easily as they can, and they are a little too forward-positioned in the chair to comfortably sit close to my desk, because even in the lowest height position, they don't allow me to go under the desk like is possible with my Herman Miller. I also feel like this chair could have been delivered partially constructed, especially the armrests on the seat, and why the aluminum base wasn't already pre-constructed (without the castors) is baffling, considering it would have fit in one of the two boxes that way. The instructions also need to be clearer. On the pamphlet, there's an A to X listing (which is also used in the steps), but none of the physical parts use this lettering system! What I did like I'll be honest, I haven't used it for very long, just one week, and seating comfort is subjective after all! Any spills wiped straight off it, the stitching, and the lines look great, not a fray to be seen or stitch out of place. It looks kind of cool, too. My favorite feature of these seats is the nap mode. While you're not lying completely flat, it leans far back enough to make you easily doze off after a heavy gaming or working session. Overall, this chair offers plenty of comfort features. The MSRP does vary quite a bit depending on the region, at £549.99 in the UK, and €580 in Europe, and $599 before tax in the U.S. However, shipping is free, which is a bonus for such a heavy item. Is it worth it, though? At three years' warranty, I think it's a decent deal. Another firm out of Germany sent me a free replacement hydraulic gas spring for a chair that failed after almost four years, so it was well outside its two-year warranty. My advice is to always try, as you might have the same luck I did. If I could fault it at all, it would be the constant shifting of the armrests and backrest. Where to buy Although the footrest variant normally costs $539.99, it has been discounted to $469.99 on the official website in Black or White. In fact, the non-footrest variant is only $40 cheaper. On Amazon, it currently costs more at $499.99 links below. Sihoo Doro C300 Pro V2 for $469.99 (official website) Sihoo Doro C300 Pro V2 for $499.99 at Amazon US SIHOO provided a free sample without any review or pre-approval. Good to know This Amazon link is U.S. specific, and not available in other regions unless specified. We only use first-party seller links (at the time of article publishing); ensure that you purchase from a first-party seller link only. Check out Today's Deals on Amazon | or our recent tech deals. Become a Prime member (for Students or SNAP) via Neowin Get Prime Access - Prime for half price (for qualifying Medicaid, EBT, SNAP) Subscribe to Prime Video, Audible Plus, Music Unlimited or Kindle Unlimited via Neowin As an Amazon Associate, we earn from qualifying purchases.
    • Making US citizens pay is a prominent tool? Joke of the week…
    • Price Drop: Save 86% on Microsoft Office 2021 Professional Plus lifetime digital license by Steven Parker Today's highlighted deal comes via our Apps + Software section of the Neowin Deals store, where you can save 86% on a lifetime license to Microsoft Office 2021 for Windows. This bundle is for families and small businesses who want classic Office apps and email. It includes Word, Excel, PowerPoint, Outlook, Teams, and OneNote. A one-time purchase installed on 1 Windows PC for use at home or work. Lifetime license for MS Word, Excel, PowerPoint, Outlook, Teams, & OneNote One-time purchase installed on 1 Windows PC for use at home or work Instant Delivery & Download – access your software license keys and download links instantly Free customer service – only the best support! Microsoft Office Professional 2021 (for Windows) includes: Microsoft Office Word Microsoft Office Excel Microsoft Office PowerPoint Microsoft Office Outlook Microsoft Office Teams Microsoft Office OneNote Microsoft Office Publisher Microsoft Office Access No faffing about with subscriptions, just classic apps that don't expire. Good to Know ONE-TIME PURCHASE INSTALLED ON 1 DEVICE Redemption deadline: redeem your code within 30 days of purchase Access options: desktop Full versions No subscriptions – no monthly/annual fees Version: 2021 Updates included* *Support for this version of Office ends on Oct 13, 2026 A lifetime subscription to Microsoft Office 2021 Professional normally costs $219.99, but this deal can be yours for just $29.97, that's a saving of $190. For full terms, specifications, and license info, click the link below. Get Microsoft Office Professional 2021 for just $29.97, or learn more Although priced in U.S. dollars, this deal is available for digital purchase worldwide. Support queries If you have queries or need support for any of the Neowin Deals, please use the contact form here. Neowin Deals are managed and sold by StackCommerce who represent Neowin on an affiliate basis. Why we post these deals We post these because we earn commission on each sale so as not to rely solely on advertising, which many of our readers block. It all helps toward paying staff reporters, servers and hosting costs. So for those that keep moaning and complaining, be thankful we're still online for you to even do that. Other ways to support Neowin Whitelist Neowin by not blocking our ads Create a free member account to see fewer ads Make a donation to support our day to day running costs Subscribe to Neowin - for $14 a year, or $28 a year for an ad-free experience Disclosure: Neowin benefits from revenue of each sale made through our branded deals site powered by StackCommerce.
    • The only reason I want to know where you from is because if you are not from the U.K, then why should you care what we in the U.K do or don't do? Racist I am not, I am fed up with the amount coming over here and feel they can come over here and think we need to support them. Do you know how much it costs this country to support these people coming over here? Even when we give them a place to live it is not good enough. We had a barge that was being used to house immigrants, oh but that was not good enough. A mate said to me at the time, when he was homeless, he would have been happy to live on the barge, instead of ending up sleeping on a bench on the beach. I am not scared to say what my family heritage is, unlike you who is scared to say where they are from or where they live. Father side U.S, mother side Wales, still have family living in the U.S. A mate who sadly died a few years ago, had a load of people from different races recording in his studio, I got on with all of them. Skin colour don't bother me, where they are from don't bother me. Religion don't bother me as long as they don't push it onto me and it is not crazy stuff. I am not religious. But if you are not living in the U.K, then why should you care if we are in the E.U or not? This the problem, too many people poking their noses into where it don't belong. But you believe what you believe, if you think I am racist, then be it, I really do not care. Just grow a pair
  • Recent Achievements

    • Conversation Starter
      jessse3334 earned a badge
      Conversation Starter
    • Reacting Well
      JuvenileDelinquent earned a badge
      Reacting Well
    • One Month Later
      Excellence2025 earned a badge
      One Month Later
    • Week One Done
      Excellence2025 earned a badge
      Week One Done
    • Week One Done
      flexorcist earned a badge
      Week One Done
  • Popular Contributors

    1. 1
      +primortal
      506
    2. 2
      +Edouard
      206
    3. 3
      PsYcHoKiLLa
      151
    4. 4
      Steven P.
      73
    5. 5
      macoman
      62
  • Tell a friend

    Love Neowin? Tell a friend!