Networked visited by University of Michigan


Recommended Posts

Nuked the router. I'm setting up everything slowly. 

 

Did a reset to default settings. Within about 5 minutes from doing it "DNS_PROBE_FAILED" popped up in Google.

 

So far this is what I've done.

 

- Disabled IPv6

- Reset Router to Default settings

- Changed DNS Servers

 

Also, BudMan asked me in PM, if I could ping my gateway when it was happening, answer is no. It failed. I'm assuming the router is going up in flames.

 

Also, I figured this out because Netflix died, mobile devices suffered from it. So, it's looking like my router is dying.

when you say you can not ping your gateway do you mean your router???  192.168.1.1 or your ISP??  you need to try and ping both... if you can ping your router but not your isp it could be your isp just down..  If you can not ping your router then pretty much its toast..   Or you have something wrong with your machine.  Can you ping other stuff on your network - if so then your machine is fine..

 

its a tp-link right... You could put dd-wrt on it most likely.  That firmware is way better than the native ######...

5 hours ago, BudMan said:

when you say you can not ping your gateway do you mean your router???  192.168.1.1 or your ISP??  you need to try and ping both... if you can ping your router but not your isp it could be your isp just down..  If you can not ping your router then pretty much its toast..   Or you have something wrong with your machine.  Can you ping other stuff on your network - if so then your machine is fine..

 

its a tp-link right... You could put dd-wrt on it most likely.  That firmware is way better than the native ######...

Well.. I probably will, but I do need to change the gear anyways. I'm giving this router to my mom for her new apartment. 

 

I did what you suggested in your PM, Ping my DG and a website. This is the results;

 

C:\Users\BinaryData>ping 192.168.1.1

Pinging 192.168.1.1 with 32 bytes of data:
Request timed out.
Request timed out.
Reply from 192.168.1.100: Destination host unreachable.
Request timed out.

Ping statistics for 192.168.1.1:
    Packets: Sent = 4, Received = 1, Lost = 3 (75% loss),

 

C:\Users\BinaryData>ping www.cnn.com
Ping request could not find host www.cnn.com. Please check the name and try again.

 

When I ping my ISPs DG for my IP, it fails 3x then 4th one it responds.

well here is the thing if you can not talk to your gateway, your not going to be able to find the IP for www.cnn.com so that test just shows that yeah you can not talk to your gateway.

 

When you can not talk to your router IP, can you ping other devices on your network?  which also could be just an issue with that router still if your all connected into its lan ports for your switching.

 

So, its really like a 10 min fix to just upgrade the router to dd-wrt and see if this makes this problem go away.  you can always still give it away once you get in the new setup.

1 hour ago, BudMan said:

well here is the thing if you can not talk to your gateway, your not going to be able to find the IP for www.cnn.com so that test just shows that yeah you can not talk to your gateway.

 

When you can not talk to your router IP, can you ping other devices on your network?  which also could be just an issue with that router still if your all connected into its lan ports for your switching.

 

So, its really like a 10 min fix to just upgrade the router to dd-wrt and see if this makes this problem go away.  you can always still give it away once you get in the new setup.

So, dd-wrt it is. What are the chances of screwing it up to the point of it no longer working? :p

Normal person pretty freaking low like 1 in a 1000... You prob more like 1 in 10 ;) heheheh j/k its pretty freaking straight forward... Most devices it just simple upload of the new firmware using the current firmwares upgrade web ui..  What is the exact model of this tp-link and will look up the dd-wrt instructions.

 

here you go

http://www.dd-wrt.com/wiki/index.php/TP-Link_TL-WDR4300#How_to_Flash

 

How to Flash

    Download factory-to-ddwrt.bin and tl-wdr4300-webflash.bin from the router database.
    Optional: Download tl-wdr4300v1-webrevert.rar in case you need to restore to stock firmware.
    Remove Ethernet cable from the WAN port on the router.
    Perform a 30/30/30 reset.
    Using Internet Explorer and a PC connected via Ethernet, flash factory_to_dd-wrt.bin using the web interface.
    Confirm the router has rebooted by visiting http://192.168.1.1
    Perform a 30/30/30 reset.
    Visit http://192.168.1.1 and flash the tl-wdr4300-webflash.bin file.
    After the router has finished rebooting, do another 30/30/30 reset.
    Plug the Ethernet cable into the WAN port, and visit http://192.168.1.1 to setup your preferences.

 

Any monkey could do that in like 5 minutes with ZERO change of FU...

 

Then here are links to the lastest and greatest versions

ftp://ftp.dd-wrt.com/betas/2016/02-15-2016-r29085/tplink_tl-wdr4300v1/

2 hours ago, Circaflex said:

Ahhh... That makes sense. Though I'm a bit nervous doing it now, haha.

 

Edit:

 

My router doesn't default to 192.168.1.1, it defaults to 192.168.0.1, I suppose that doesn't make a difference, correct?

Edited by BinaryData

Dude I have done this hundreds of times...  Only an issue once when I had too many beers ;)  And flashed the wrong version to the router... But was able to recover it..

 

But clearly its spelled out for you the correct files to grab... If it didn't work pretty sure there would be comments all over that wiki article, etc.

 

And you don't really have to do the 30/30/30 I rarely did that and didn't have any issues.. Doesn't matter what your router defaults too, once its on dd-wrt it will default to 192.168.1.1

 

edit: you flashing a tp-link reminds I should prob update the one I have sitting on my junk pile that I bring with me when might need a router, etc..

yeah the official stance is full reset, upgrade to dd-wrt, full reset... Any time you update to newer version of dd-wrt, full reset before and after..  I have never once done it so many times, sometimes never and have not had issues.

 

But it sure doesn't hurt to do it that way.  And that your sure its clean install with nothing hanging over in nvram, etc.

 

This really is a 5 min process, you should of done it long ago when it was first suggested in the beginning of this thread.  In all the times I have done this I have never seen a router be less stable after going to dd-wrt than the native..  i have a tp-link 3600.. And the native firmware was on it all of 5 minutes... Booted it, checked it out - could tell it was crap... Loaded dd-wrt before ever got put into actual use.

 

You have to really F it up to brick the things.. Even if you install the wrong version, you can quite often recover them...  When I did it when I was drunk, just used the paperclip trick to short 2 pins on a cheap and got the correct firmware loaded.. Common mistake made even when doing native firmware upgrades is users try and upgrade via wireless - that is ALWAYS bad idea!!!  Connect with a wire to the router and your fine.

Keep in mind Circaflex, we are talking about BD... If anyone can mess it up - he can ;)  But like I said even when I was 13 sheets to the wind and installed the WRONG firmware...  I was able to recover it, while even more booze in me..  So it really quite difficult to brick them...

 

So are you done yet? You stated you were going to do it 3 hours ago ;)

Wait what? If you are still on the stock firmware, do the hard reset to clear any crud that was setup during this mess. Plug ethernet cable into a laptop and into the router, login, flash the ddwrt firmware. Thats all. You can definitely connect to a router via hardwire without the router having a wan cable plugged in, that is how i did the archer c7. I dont see why you couldnt leave the wan cable connected, shouldnt be a problem, but I am sure @BudMancan chime in for that.

6 minutes ago, Circaflex said:

Wait what? If you are still on the stock firmware, do the hard reset to clear any crud that was setup during this mess. Plug ethernet cable into a laptop and into the router, login, flash the ddwrt firmware. Thats all. You can definitely connect to a router via hardwire without the router having a wan cable plugged in, that is how i did the archer c7.

Except it doesnt. I've done it before but it won't let me. Now I can't get Internet back. Ffs....

 

I'm done screwing around with this. I did the hard reset like it said too. Apparently i bought a pos router. I'll stick with this junk until Friday and buy my firewall, switch, and wap then.  This is more than a 5 minute process, BudMan. I don't screw around with modding things or doing things like this. I've never installed ddwrt before, and clearly I'm about as useful as USB1 is fast.

You can't be afraid to break stuff.  That is all part of learning in this field.  If I were afraid to break stuff, I would never leave the house. 

 

broken snow shovel, check...shoes fell apart, check....lost a few lugnuts, check....borked a rds server gateway, check....

 

crap happens, sometimes it happens all at once.  When it does happen, regardless of how much it cost you, you work through it.    If you give up or don't want to play with it until it works, this is not the field for you. 

 

Patience and being able to work through the issue (no matter how major or small it is) is what is needed in this field. 

 

Do you think I give up when a server decides that it doesn't want to power on...and the entire multimillion dollar company is relying on this server to be up to be able to cash checks (banking check processing server, there was only one), did you think I said f it, it is broke?  No I worked through the issue, regardless of how stupid the "fix" was  (powering on and off the system for about 7 hours, and yes it did eventually power on with me just hitting the power button until 4 am).  I never gave up on that crap box. 

 

Rule one: take your time.  It takes as long as it does to get it right. 

Rule two: don't get frustrated.  Leave and come back if you are burnt out.  It may come to you in 30 seconds after you have had some sleep.

 

 

 

 

 

I'm not afraid to break things, not at all. But if this does break, I'm without internet for the next week, I don't have the cash to replace it right now, spent a little too much on my new TV, lol. I'd prefer to have a back up in case this didn't work.

 

What I did was..

 

1. Unplugged wan.

2. Performed 30/30/30

3. Attempted to go to 192.168.0.1 (didn't work)

4. Set my IP to 192.168.0.100 (defaults to 100 - 199)

5. Set my subnet to 255.255.255.0 (default)

6. Set my dg to 192.168.0.1

7. Set my dg to nothing

 

Still didn't work. Tried everything I knew, even went back to the manual to try and figure it out. Googled a bunch of different things, and nothing. None of my PCs could access it, I was getting a 169 Address..

 

Edit:

 

Do I absolutely HAVE to remove the WAN connection?

you can go to the store and pick up a router for 20 bux if needed.  I know I have a staples, walmart, target, etc that I can pickup a cheapy router if needed (besides I do have a few laying around, but if I didn't there are options)

 

192.168.1.1?

don't forget to set your pc to 192.168.1.100 or something in that range.

 

 

just an example of said cheap router

http://www.staples.com/Comtrend-WR-5881-Wireless-4-Port-Router-10-100-MbPS-WL-N-RTR/product_IM1QM6706

5 minutes ago, sc302 said:

you can go to the store and pick up a router for 20 bux if needed.  I know I have a staples, walmart, target, etc that I can pickup a cheapy router if needed (besides I do have a few laying around, but if I didn't there are options)

 

192.168.1.1?

don't forget to set your pc to 192.168.1.100 or something in that range.

 

 

just an example of said cheap router

http://www.staples.com/Comtrend-WR-5881-Wireless-4-Port-Router-10-100-MbPS-WL-N-RTR/product_IM1QM6706

My router defaults to 192.168.0.1. I don't know why but apparently TP-Link wants to be special, and annoy people.

 

I set my IP to 192.168.0.100, and nothing. The connection wasn't made. I had no "internet".

Something sounds way off. Hard reset the router using the paperclip method (poke the reset button), plug into router via ethernet. At this point, you arent getting internet so just unplug the WAN cable just in case it was causing a problem, and profit. You dont need to set any ips, mess with the subnet, none of that. Just connect via a physical cable to the router and flash away.

This topic is now closed to further replies.
  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Posts

    • Micron reveals AI companies are spending billions to lock up its memory years in advance by Karthik Mudaliar The demand for more memory is far from over, and Micron is turning the AI-driven memory shortage into a much more predictable business. The company has revealed that it has signed 16 strategic supply agreements backed by roughly $22 billion in customer deposits and other financial commitments. The contracts cover DRAM and NAND deliveries over several years, with some running through 2030. With the AI boom, demand for high-bandwidth memory (HBM) has grown so quickly that large customers are now prepared to help finance future production in exchange for a guaranteed supply. According to Micron’s latest financial results, the company received commitments worth about $22 billion across its new agreements. Around $18 billion is expected to arrive as cash deposits, while the rest will come through other financial arrangements. Micron says the agreements could generate approximately $100 billion in future contracted obligations. They cover around 20% of its expected DRAM shipments and one-third of its NAND shipments during their respective terms. It should be noted that although AI infrastructure is the main force behind the current shortage, not all 16 agreements with Micron involve AI companies. Micron said the customers also include consumer electronics and automotive businesses, two sectors that increasingly compete with data centers for the same manufacturing capacity. HBM is consuming an increasing share of that supply. Unlike conventional desktop or server RAM, HBM stacks multiple memory dies vertically and places them close to an AI accelerator. This gives GPUs and other AI chips access to data at much higher speeds, but it also requires more complicated manufacturing and packaging. Micron says its 12-layer HBM4 memory is now shipping in high volume for a lead customer, with samples also supplied to other companies. The chipmaker has already generated more than $1 billion in HBM4 revenue and says the product is ramping twice as quickly as its earlier HBM3E generation. Samsung has similarly warned that the memory shortage could continue into 2027 and beyond. Consumer memory companies have also had to address sharp increases in DDR5 pricing, suggesting the effects are already reaching beyond the data center. For consumers, that could mean the AI memory crunch lasts longer than expected, even as manufacturers invest heavily in new production.
    • XnConvert 1.112 by Razvan Serea  XnConvert is a cross-platform batch image-converter and resizer with a powerful and ease of use experience. All common picture and graphics formats are supported (i.e. JPG, PNG, TIFF, GIF, Camera RAW, JPEG2000, WebP, OpenEXR) as well as supporting over 500 other image formats. Also available within the batch operations include rotating, adding of watermarks, adding of text along with many image-adjustment features such as brightness, shadows and more. Among the features included are: Batch adding of files and folders Support for drag and drop of files Batch rotating, cropping, resizing and more Adding of photo masks Preserving or removing image metadata in conversions Multipage image file support (i.e animated GIF, APNG, TIFF) Command line integration via NConvert Filters - such as 'Blur', 'Gaussian Blur', 'Emboss', "Sharpen' and much more Effects - such as 'Old camera' and much more Download: XnConvert 64-bit | Standalone | ~30.0 MB (Freeware) Download: XnConvert 32-bit | Standalone Links: XnConvert Website | Screenshot | Release Announcement Get alerted to all of our Software updates on Twitter at @NeowinSoftware
    • Microsoft updates Visual Studio Code with chat cost tracking and multi-agent chats by Paul Hill Microsoft has just launched Visual Studio Code 1.126, its latest weekly release. This time, the company has focused on letting you see the total cost of chat sessions to spot expensive conversations; enabling multiple chats per session that run side-by-side in one agent host Copilot session; and letting you browse new folders safely in restricted mode. We have now reached the stage where free AI in IDEs is coming to an end. To help you keep track of your costs, VS Code now lets you see the entire cost of a chat session, rather than just individual turns. This should give you more transparency about which sessions consume the most credits, so you can better manage your usage over time and spend less. For those of you using the Agents window, you know it is possible to run and manage multiple agent sessions at once. In this update, a Copilot session started from an agent host can hold several chats at once. Explaining how this feature works, Microsoft writes: Finally, from this update forward, Microsoft will remove the pop-up when opening an untrusted folder. When you open a new folder now, it will automatically open in Restricted Mode. You will see a banner that lets you manage the trust level of the folder. Microsoft has made this change so that it’s easier to start inspecting code without giving it trust right away. If you have VS Code, you can check for updates within the app now to get this new version. Otherwise, you can download it from the Visual Studio Code website.
    • Anthropic accuses Alibaba of using 25,000 fake accounts to copy Claude's capabilities by Karthik Mudaliar Anthropic has accused Alibaba of using nearly 25,000 fraudulent accounts to extract capabilities from Claude on a huge scale. According to a report from Reuters, Anthropic told US lawmakers that operators linked to Alibaba and the company’s Qwen AI team generated 28.8 million exchanges with Claude between April 22 and June 5, 2026. That is a lot of Claude conversations, but Anthropic says this was not ordinary chatbot use. The company believes the accounts were part of a coordinated effort to collect answers that could help train or improve rival AI systems. The alleged campaign reportedly focused on some of Claude’s most valuable skills, including software development, multi-step reasoning, and agentic tasks. In practical terms, that means getting an AI model to plan and complete work across several stages rather than simply answering a single question. This is called 'distillation,' where AI companies use outputs from a larger model to train a smaller and cheaper one. The smaller model learns to imitate useful parts of the more capable system without needing the same amount of computing power. The distillation process isn't automatically suspicious, but the problem comes when one company gathers another provider's outputs without permission and at an industrial scale. Also, this does not mean Alibaba obtained Claude’s source code, model weights, or original training data. Instead, Anthropic claims the accounts repeatedly asked Claude carefully designed questions and collected the answers. Those answers could then be used as training material for another model. Anthropic has made similar accusations against DeepSeek, Moonshot AI, and MiniMax earlier this year. As Neowin previously reported, Anthropic said those three companies collectively generated more than 16 million Claude exchanges through roughly 24,000 accounts. Anthropic says the new campaign produced almost twice as many exchanges in a matter of weeks. Anthropic reportedly told lawmakers that the campaign could help Chinese AI developers approach the capabilities of its Mythos Preview model. Mythos is focused on advanced cybersecurity work, including finding and exploiting complex software vulnerabilities. via Reuters | Photo via DepositPhotos.com
  • Recent Achievements

    • Rookie
      krychek57 went up a rank
      Rookie
    • Grand Master
      Jaybonaut went up a rank
      Grand Master
    • One Year In
      Philsl earned a badge
      One Year In
    • Dedicated
      Scoobystu earned a badge
      Dedicated
    • First Post
      Tom Schmidt earned a badge
      First Post
  • Popular Contributors

    1. 1
      +primortal
      441
    2. 2
      +Edouard
      175
    3. 3
      PsYcHoKiLLa
      134
    4. 4
      Michael Scrip
      79
    5. 5
      Xenon
      77
  • Tell a friend

    Love Neowin? Tell a friend!